Manuel d'utilisation / d'entretien du produit WBS510 du fabricant TP-Link
Aller à la page of 21
I nstallation Guide Outdoor Wireless Base Station WBS210 / WBS510 C OPY RIGHT & TRADEMARKS is a register ed trademark of TP -LINK TECHNOLOGIES C O., L TD . Other brands and product names are trademarks or register ed trademarks of their respective holders.
C ontents Overview . Package Contents . Panel Layout Hardwar e Installation Connect cables Mount Antenna Power On Lightning and ESD Pr otection Specification FA Q 1 1 2 3 4 5 7 8 15 16 9 Config uration with P harOS Log in to the PharOS Configure the Base Station .
Overview TP-LINK's Outdoor Wireless Base Stations of the Phar os series products are designed f or outdoor wireless network solutions, aiming at long-distance transmission and large coverage of wireless network .
The panel of Base Station: Panel Layout RESET Shielded Ethernet Port LAN1 Shielded Ethernet Port LAN0(POE IN) Grounding Terminal 2 AP/AP Router mode: All four LEDs remain solid . Client/Bridge/Repeater/AP Client Router mode: The more lit LEDs indicate the better wireless sig nal strength.
Passive PoE Adapter Hardw are Installation 3 The Outdoor Wireless Base Stations require external antenna that corresponds to your network environment; a dish antenna for Point-to-Point (PtP) bridge environment, a sector antenna for Point-to-MultiPoint (PtMP) environment, or a columnar antenna for Hotspot environment.
4 Affix the waterproof rubber insert to the underside of the device for waterproofing and replace the cover until it firmly locks into place. Use an adequate Ethernet cable (Lenth up to 60m) to connect the LAN0 (POE IN) port. Shielded CAT5e (or above) cable with an integrated ground wire is recommended.
Attach the protective cap. Push and slide the protective cap down over the Base Station until it firmly locks into place. Align the mounting tabs on the back of the Base Station with the four slots of the mounting bracket. Push and slide the Base Station downward until it locks into place.
6 Loosen and completely remove the end of the metal strap by turning the captive screw counterclockwise with a flathead screwdriver. Position the Base Station and wrap the metal strap around the pole.
7 Connect the Ethernet cable from the Base Station to the POE port of the PoE adapter. Connect an Ethernet cable from your LAN device (a computer, router or switch) to the LAN port on the PoE adapter. Connect the power cord to the power port on the PoE adapter and plug it into an electrical outlet.
Lightning and ESD P rotection Use a shielded CAT5e (or above) cable with an integrated grounding wire for connection. If you have the standard CAT5e cable for the connection, use a separate grounding cable to connect the grounding Terminal (GND) to earth ground.
Open a web browser, type http://192.168.0.254 into the address field and press Enter (Windows) or return (Mac). It is recommended to use the latest version of Google Chrome, Firefox or Safari. C onfiguration with PharOS Log in to the PharOS Before accessing the PharOS Web Interface, you need to assign a static IP address 192.
Enter admin for both User Name and Password , then select your Region from the drop-down list. Read and agree the terms of use, then click Login . Change the default User Name and Password to protect your Base Station. Let’s start configuring the Base Staion.
1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Click Next . 4. Wireless AP Settings: a. Create a new SSID (Network name) for your wireless network. b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP.
Point to MultiPoint (PtMP) Configure the Client 12 AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP AP Client Router LAN:192.168.0.254 WAN:Dynamic IP 1. Log in to PharOS and go to the Quick Setup page.
13 Configure the Access Point Configure the AP Client Router (CPEs) 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next . 3. LAN Settings: Set the IP Address to the same subnet with the root AP or router that you want to connect to, and click Next.
14 Hotspot Configure the Access Point Smartphone Laptop Tablet Access Point Hotspot is used to provide Internet access to wireless devices such as smartphones, tablets and laptops. Typically, columnar antennas are used in this environment. 1. Log in to PharOS and go to the Quick Setup page.
Specification H ardware features Wireless features Interface Dimensions Models Maximum Transmit Power 2 Operating Frequency 2 802.11 Standards Power Supply ESD Protection 1 Lightning Protection 1 Oper.
FA Q How to restore the Base Station to its factory default settings? With the Base Station powered on, press and hold the RESET button on the Base Station or the Remote Reset button on the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash.
2. Click Start , the PharOS will begin to analyze the power of frequency . Observe the curves for a period of time, and then click stop. Note that the relatively low and continuous part of the average curve indicates less radio noise. Here, we use the figure below as an example.
FC C ST A TEMENT CE M ark W arnin g IC ST A TEMENT Safety Information This equipment has been tested and found to comply with the limits f or a Class A digital device, pursuant to part 15 of the FCC Rules.
NC C Notice & BSMI Notic e 注意！ 安全諮詢及注意事項 依據 低功率電波輻射性電機管理辦法 第十二 條 經型式認證合格之低功率射頻電 機 ，非經許 可 ，.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TP-Link WBS510 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TP-Link WBS510 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TP-Link WBS510, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TP-Link WBS510 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TP-Link WBS510, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TP-Link WBS510.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TP-Link WBS510. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TP-Link WBS510 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
