Manuel d'utilisation / d'entretien du produit W-704C du fabricant Toshiba
Aller à la page of 48
Video Cassette Recorder W -704C OWNER’S MANUAL This publication is printed on recycled paper 70971857 PLAY STOP PROG.TV POWER EJECT PAUSE/STILL REC REV FF.
2 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
3 INTRODUCTION IMPORT ANT PRECAUTIONS Save Original Packing Materials The original shipping carton and packing materials will come in handy if you ever have to ship your VCR. For maximum protection, repack the set as it was originally packed at the factory.
4 1. Read owner’s manual After unpacking this product, read the owner’s manual carefully, and follow all the operating and other instructions. 2. Power Sources This product should be operated only from the type of power source indicated on the marking label.
5 INTRODUCTION 6. Water and Moisture Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and the like. 7. Cleaning Unplug this product from the wall outlet before cleaning.
6 16. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen into the product.
7 INTRODUCTION INTRODUCTION Provides important notes and general explanation of the VCR, including names of the buttons, jacks, etc. SAFETY PRECAUTIONS .................... 2 IMPORT ANT PRECAUTIONS .............. 3 IMPORT ANT SAFETY INSTRUCTIONS .....
8 Front Panel Remote Control * These buttons are used to control the cursor on the screen. INTRODUCTION Identification of Controls See the page in for details. This manual shows the names of buttons in italics. To operate this VCR. 78 0 100 9 6 5 23 4 1 STOP PLAY/x2 FF REW SLOW PAUSE/STILL CANCEL A.
9 INTRODUCTION Rear Panel LINE IN 1 AUDIO (Rear), 2 (Front) jacks If the connected equipment is monaural (has one audio output jack), connect the L (MONO) side, the same sound is recorded on both L and R on the Hi-Fi track.
10 Setting up the Remote Control 1 Open the batter y compar tment lid on the rear panel. 2 Install 2 batteries (“AAA” size) f ollowing the polarity diagrams. 3 Close the batter y compar tment lid. 4 P oint the remote control at the VCR and press the buttons within the operating r ange.
11 PREP ARA TION Antenna/VCR/TV Connection 1 Disconnect the antenna cab le from y our TV and connect it to the RF IN terminal on the VCR. 2 Connect the RF OUT terminal to the TV . AUDIO/VIDEO Connections The A UDIO/VIDEO jac ks are also av ailable to connect your TV .
12 Cable Connection Choose one of the below according to y our usage of the cable bo x. This set-up will enable you to: – record an unscramb led channel. – watch an unscramb led channel while recording it. – record an unscramb led channel while watching another (only when y ou connect a cab le- compatible TV).
13 PREP ARA TION This set-up will enable you to: – watch an unscramb led or scrambled channel while recording it. – record any channels through the cab le box.
14 Auto Set Up 1 Connect the antenna cable to the VCR (see page 11). Then connect the VCR’ s pow er plug to an A C outlet. “A uto” flashes in the VCR display as the VCR automatically tunes in all activ e stations . When A uto Set Up is completed successfully , the current time will be display ed.
15 PREP ARA TION SET UP PROGRAM PRESET PROG H 120 0 16 80 1 OF F O OF F O U AT O U A M EG R FA S P E TA P E L E SAP S E T SI M U L C A S T GT AN T E A LA n nn n n n OF F O n n GUA G X DS I n O F E n ED : n Optional settings on the SET UP screen Other optional settings can be made .
16 Initial Settings Using On-Screen Display (continued) 8 Press ENTER to star t the “A UT O” clock set f eature. After a while, the VCR automatically updates the clock using the data broadcast b y the local TV stations. The f ollowing screen will appear on TV depending on the broadcast at y our location.
17 PREP ARA TION Incoming Antenna/Cable (CATV) Signals The VCR scans through all receivab le TV and CA TV channels and stores only the active ones in your area into the memory . Once the storing is finished, y ou can select a desired channel using CH/TRK .
18 To add channels To erase channels Adding or erasing channels Adding channels If a desired channel cannot be scanned automatically because of a weak signal, it can be added to the memor y . Erasing channels Y ou can erase a stored channel from the memory if it is unnecessar y .
19 PREP ARA TION Video Cassette Use Loading a cassette Push the cassette into the cassette compar tment with the window side f acing up and the label side tow ards the front. The VCR is automatically turned on. The indicator will appear in the VCR displa y .
20 Adjusting the tracking When pla yback star ts, the VCR automatically adjusts the trac king for clear pictures and sound (Digital A uto T rac king). The “DT” indicator b links dur ing the adjusting. If the VCR cannot locate the best possib le trac king point, hold down one of CH/TRK to adjust the trac king manually .
21 PLA YBACK PLA YBACK V ariable Speed Playback You can play back a tape at various tape speeds. Picture Search A tape runs at 5 times or 7 times the nor mal playbac k speed so that you can quic kly locate a par ticular scene. 1 Press FF or REW dur ing pla yback.
22 Frame Advance A picture adv ances frame by frame . 1 Press PLA Y/x2 during still playbac k. Each time you press PLA Y/x2 , the picture advances one fr ame. If y ou press and hold PLA Y/x2 , the tape runs at 1/30th the normal playback speed. To resume normal playback Press P AUSE/STILL .
23 PLA YBACK Counter Function Y ou can view the cloc k, linear time counter or tape remaining time in the VCR displa y or on the TV screen. 1 Each time y ou press REMAIN/COUNTER , the VCR displa y changes in sequence as f ollows: The indication abov e will also appear on the TV screen by pressing DISPLA Y .
24 Index Search Function The VCR can find a point where a registered index signal is on a tape and pla y back f or about 5 seconds. Y ou can easily locate the desired prog ram by inputting the inde x signal. Registering index signals Each time a recording star ts, an inde x signal is automatically registered.
25 RECORDING Watching a TV program while recording another 1) While recording, press TV/VCR to tur n off “VCR” indicator . 2) Choose another channel using the channel selector on the TV . Skipping unnecessary scenes while recording Press P AUSE/STILL to stop recording momentarily .
26 Timer Programming Procedure Example : T o record cab le channel 25 in the SP tape speed from 9:30 p .m. until 10:00 p.m. on A ugust 30. T oday is A ugust 25. 1 Load a cassette with the saf ety tab attached. 2 Press PROG. to displa y the MENU screen.
27 RECORDING Auto Speed Select If you are not sure the tape is long enough f or timer program recording in the SP tape speed, set the recording tape speed to “A UT O”. Recording star ts in the SP tape speed and the VCR automatically selects the tape speed to record the program to the end.
28 If a power failure occurs during the timer program recording (including VCR Plus+ C 3 ® system recording (page 31)) • When a pow er f ailure has occurred, “- -:- -” appears in the VCR displa y . Since the progr ammed contents ha ve been cleared, reset the clock and timer prog ramming.
29 RECORDING The flow char t below will giv e y ou an idea as to what must be done to use the VCR Plus+ C 3 ® system feature. Setting the Clock (page 16) ↓ Cable Box Set-up (page 33) ↓ Storing Ch.
30 Guide Channel Setting 1 Press PROG. . 2 Select “PRESET” using FF or REW , and press ENTER . 3 Select “CH MEMOR Y” using PLA Y/x2 or ST OP , and press ENTER . 4 Set “TV/CA TV” to “TV” or “CA TV” using FF or REW . 5 Press PROG. to return to the PRESET screen.
31 RECORDING VCR Plus+ C 3 ® system Programming 1 Press VCR Plus+ . The VCR Plus+ screen appears. 2 Enter a PlusCode ® prog ramming number . Example : T o record a program with the PlusCode ® programming number 36295 (fictitious code). Press number button 3, 6, 2, 9 and 5 .
32 Confirming the VCR Plus+ C 3 ® system timer programs Before the VCR enters the timer standby mode (TIMER indicator not lit) 1) Press PROG. to display the MENU screen. 2) Press ENTER to select “PROGRAM”. Chec k the programmed data. 3) Press PROG.
33 RECORDING Cable Box Set-up The VCR can directly control channel selecting of the connected cable box. RECORDING Cable Box Control This VCR needs to be connected to a cab le bo x equipped with an infrared wireless remote control. Y ou can select cable channels from the cab le box b y operating this VCR.
34 Cable Box Set-up (continued) Cable Box Set-up 1 Press PROG. to displa y the MENU screen. 2 Select “PRESET” using FF or REW , and press ENTER . 3 Select “CABLE BO X/DSS” using PLA Y/x2 or ST OP , and press ENTER . 4 Select “NO” or “C .
35 RECORDING VCR display Cable box display Cable channel number 7 Select “BRAND TYPE” using ST OP , and enter a brand code of y our cable bo x using number buttons . Ref er to the tab le on the ne xt page. Example : F or a T OSHIBA cab le box, identified b y number 36.
36 Table of cable box brand codes Toshiba 36 Anvision 13, 20, 21, 22, 23, 24, 25, 26, 58, 62, 84 Archer 1, 20, 21, 29, 42, 44, 63, 88, 91 Cablestar 13, 20, 21, 22, 23, 24, 25, 26, 58, 62, 84 Cableview.
37 RECORDING DSS ® Satellite Receiver Set-up The VCR can directly control channel selecting of the connected DSS ® satellite receiver. RECORDING DSS ® Satellite Receiver Control This VCR needs to be connected to a DSS ® satellite receiv er equipped with an infrared wireless remote control.
38 DSS ® Satellite Receiver Set-up (continued) DSS ® Satellite Receiver Set-up 1 Press PROG. to displa y the MENU screen. 2 Select “PRESET” using FF or REW , and press ENTER . 3 Select “CABLE BO X/DSS” using PLA Y/x2 or STOP , and press ENTER .
39 RECORDING VCR display 6 Select “CONTR OL ” using PLA Y/x2 or STOP , and set to “ON” or “OFF” using FF or REW . ON : if y our DSS ® satellite receiv er is remote-controllab le. • Satellite channels will be selected b y CH (CABLE BO X) on the remote control.
40 Buttons to control a remote- controllable DSS ® satellite receiver Once you complete the set-up f or a remote controllable DSS ® satellite receiv er , your DSS ® satellite receiv er can be controlled by the follo wing b uttons on the remote control of the VCR.
41 RECORDING MTS Broadcast Compatibility This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to your stereo system or stereo TV, you will experience the SAP or stereo sound. Preparation Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR.
42 Simulcast Recording When TV program such as MTV, HBO or MAX is being simulcast in FM stereo in your area, the VCR can also record the simulcast sound from an FM stereo tuner or receiver onto the Hi-Fi track and normal track. Preparation • Connect the TV and stereo system to the VCR as below.
43 ADDITIONAL INFORMA TION Setting Control Codes 1 Press TV to set the remote control operating y our TV . 2 While holding do wn PROG. , enter the two digits of y our TV’ s brand code (listed on page 44) using number buttons .
44 Toshiba 01 Bell & Howell 09 Carver 10 Celebrity 03 Citizen 12 Curtis Mathes 09, 12 Dumont 14 Electro band 03 Emerson 09, 11 Fisher 09 GE 02, 07, 11 Gibralter 14 Goldstar 11 Hallmark 11 Hitachi .
45 ADDITIONAL INFORMA TION No power. • The power cord is not plugged in. – Plug the power cord into the outlet firmly . Although the power is on, the VCR will not work. • There is no cassette. – Load a cassette. (page 19) The clock does not work.
46 The remote control does not work properly. • The batteries are exhausted. – Replace all batteries. (page 10) • The remote control is operated beyond the operating range. – Make sure the remote control is within 30 ° of the remote sensor on the VCR.
47 ADDITIONAL INFORMA TION Specifications Power supply: 120 V AC, 60 Hz Power consumption: 19 W External dimensions: 430 × 96.5 × 281 mm (W.H.D.) Mass: 3.
48 CANADIAN WARRANTY TOSHIBA VIDEO CASSETTE RECORDER To obtain a “CANADIAN WARRANTY”, the consumer must complete and forward the attached “CANADIAN WARRANTY REGISTRATION FORM” to Toshiba of Ca.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Toshiba W-704C c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Toshiba W-704C - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Toshiba W-704C, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Toshiba W-704C va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Toshiba W-704C, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Toshiba W-704C.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Toshiba W-704C. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Toshiba W-704C ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
