Manuel d'utilisation / d'entretien du produit TECRA M5 du fabricant Toshiba
Aller à la page of 288
TECRA M5 TO S H I B A TECRA M5 P or table P er sonal Computer User’ s Manual.
ii User ’s Manual User ’ s Manual Copyright © 2006 by TOSHIBA Corporation. All ri ghts reserved. Under the copyright laws, this manual cannot be repr oduced in any form without the prior written permission of TOSHIBA. No pat ent liability is assumed, with respect to the use of the information contained herein.
User ’ s Manual iii User ’ s Manual FCC infor mation Product Name: TECRA M5 Model number: PTM 51 FCC notice "Dec laration of Confor mity Infor mat ion" This equipment has been tested and fo und to comply with th e limits for a Class B digital device, pursuant to part 15 of the FCC rules.
iv User ’s Manual User ’ s Manual EU Dec lar ation of Conf or mity TOSHIBA declares, that the product: P TM51* conforms to the following S tandards: This product is carrying the CE-Mark in accordance with the rela ted European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany .
User ’ s Manual v User ’ s Manual Network Compatibility Sta t ement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the add itional requirements conditional in EG 201 121.
vi User ’s Manual User ’ s Manual One of th e labels is locate d on the module. Pur suant to FCC CFR 47, Par t 68: When you are ready to install or use the modem, call your local telephone company.
User ’ s Manual vii User ’ s Manual Type of ser vice Y our modem is desi gned to be used on standard-device telephone lines. Connection to telep hone company-provided coin service (cen tral office implemented systems) is pr ohibited. Connection to pa rty lines service is subject to state tarif fs.
viii User ’ s Manual User ’ s Manual Instr uctions for IC CS -03 cer tified equipment 1. The Industry Canada l abel identif ies certified equipment.
User ’ s Manual ix User ’ s Manual Notes for Users in Austr alia and New Zealand Modem war ning notice for A ustr alia Modems connected to the Australian te lecoms network must have a valid Austel permit.
x User ’s Manual User ’ s Manual ■ Some parameters required for compliance with T elecom’s PT C S pecifications are dependent on the e quipment (PC) associated with this modem.
User ’ s Manual xi User ’ s Manual ■ The transmit level from this device is set at a fixe d level and because of this there may be circumstances where the performance is less than optimal.
xii User ’s Manual User ’ s Manual Description on Laser specification The optical drive such a s CD-ROM drive, DVD-ROM drive, DVD- ROM&CD-R/RW drive and DVD Super Multi drive that is used in this computer is equipped w ith laser . The classification l abel with the following sentence is affixed to the surface of the drive.
TECRA M5 User ’ s Manual xiii T able of Contents Preface Manual content s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xiv User ’s Manual T able of Contents USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 Optical disk d rives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15 Region codes for DVD drives and media .
User ’ s Manual xv T able of Contents Using the Fingerp rint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Points to note about the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . 4-3 How to Delete the Fingerprint Dat a .
xvi User ’s Manual T able of Contents Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Region selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 Properties menu .
User ’ s Manual xvii T able of Contents Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Battery indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 DC IN indicator .
xviii User ’s Manual T able of Contents SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Formatting an SD memor y card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Inserting an SD card .
User ’ s Manual xix T able of Contents Hardware and system checkl i st . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 System start- up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Self test .
xx User ’s Manual T able of Contents Copy Protection*9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Images*10 .
User ’ s Manual xxi TECRA M5 Pr eface Congratulations on your purchase of the TECRA M5 computer . This powerful notebook computer provides excellent expansion capability , including multimedia devices, and it is designed to provid e years of reliable, high-performance computing.
xxii User ’s Manual Preface Chapter 6, Power and Power-Up Modes , gives details on the computer ’ s power resources and battery save modes and how to set a p assword. Chapter 7, HW Setup , explains how to configure the computer using the HW Setup program and TPM.
User ’ s Manual xxiii Preface K ey oper a tion Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C .
xxiv User ’s Manual Preface.
TECRA M5 User ’ s Manual xxv Gener al Pr ecautions TOSHIBA computers are designed to optimize safety , minimize strain and withstand the rigors of portability . Ho wever, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer .
xxvi User ’ s Manual General Precautions PC car d o v erheating Some PC cards can become hot with prolonge d use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time.
User ’ s Manual 1-1 TECRA M5 Cha pter 1 Intr oduction This chapter provides an equipment checkli st, and it identifies the computer ’s features, options and accessories. Equipment chec klist Carefully unpack your computer . Save the box and p acking materials for future use.
1-2 User ’s Manual Introduction Software Microsoft ® Windows XP Professional ■ The following software is preinstalled: ■ Microsoft ® Windows XP Professional ■ Microsoft Internet Explorer ■.
User ’ s Manual 1-3 Introduction Processor Memory ■ Built-in The computer is equipped with one of the following Intel ® processors. ■ Intel ® Core TM Duo Processor , which incorporat es a 2MB leve l2 cache memory . It also supports Enhanced Intel ® S peedS tep ® T echnology .
1-4 User ’s Manual Introduction Power Disks Battery p ack The computer is powered by one rechargeable lithium-ion battery pack. Legal Footnote (Battery Life) *3 For more info rmation on the Legal F ootnote regarding Battery Life, pl ease refer to the Legal Footnote s section in Chapter 10.
User ’ s Manual 1-5 Introduction Optical disk drive Computers in this series can be configured with an optical disk drive installed in the Slim Select Bay . The available optical disk drives are described below . CD-ROM drive Some models are equi pped with a full-size, CD- ROM drive module that lets you run CD without using an adaptor .
1-6 User ’s Manual Introduction DVD-ROM&CD-R/RW drive Some models are equip ped with a full-siz e, DVD- ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor . It reads DVD-ROMs at maximum 8 speed a nd CD-ROMs at maximum 24 speed.
User ’ s Manual 1-7 Introduction Display The computer ’ LCD displ ay panel supports high-resolution video gra phics. The LCD screen can be set at a wide range of viewi ng angles for maximum comfort and readability . Keyboard TOSHIBA Dual Pointing Device Built-in 14.
1-8 User ’s Manual Introduction Ports Slots Multimedia Serial RS-232C compatible port (16 550UART compatible). External monitor Analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus (USB 2.0) The computer has Universal Serial Bu s ports that comply with the USB 2.
User ’ s Manual 1-9 Introduction Communications Modem An internal modem provides capability for data and fax communication. It suppo rts V .90 (V .9 2). Refer to V. 9 0 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions.
1-10 User ’s Manual Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other LAN systems based on Direct Sequence S pread S pectrum/Orthogonal Fre quency Division Multiplexing radio technology that comp lies with the IEEE 802.
User ’ s Manual 1-1 1 Introduction Security Wireless communication switch This switch turns the Wireless LAN and Bluetooth functions on and off. All models are provide d with Wireless Communication switch. S ome models are equipped with both Wireless LA N and Bluetooth functions.
1-12 User ’s Manual Introduction Special f eatures The following features are either un ique to TOSHIBA computers or are advanced features, which make the computer more conveni ent to use. TOSHIBA Assist button Press this button to launch an application automatically .
User ’ s Manual 1-13 Introduction Intelligent power supply A microprocessor in the computer ’ s intel ligent power supply detects the battery’s charge and calculates the remaining battery capacity . It also protects electronic components from abnormal conditions, such as voltage overload from an AC adaptor .
1-14 User ’s Manual Introduction Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. The HDD Protection function d oes not guarantee that the hard disk drive will not be damaged.
User ’ s Manual 1-15 Introduction Fingerprint utility This product has a fingerprint utility installed for the purpose of enrolling and recogn izing fingerprints. By enrolling the ID and password to the fingerprint authentica tion device, it is no longer necessary to input the password from the keyboard.
1-16 User ’s Manual Introduction TOSHIBA SD Memory Boot Utility The TOSHIBA SD memory boot utility allows you to create a bootable SD memory card to start the system.
User ’ s Manual 1-17 Introduction TOSHIBA Dual Pointing Device utility This utility has the following functions: T o disable/enable TOSHIBA Dual Pointing Device with Fn + F9 keys.
1-18 User ’s Manual Introduction Options Y ou can add a number of option s to make your computer even more powerful and convenient to use. The following options are available: TOSHIBA SD Memory Ca rd Format This utility allow s you to format an SD memory card by the SD standard format.
User ’ s Manual 1-19 Introduction Slim Select Bay options The following modules can be in st alled in the Slim Select Bay . All other modules are options.
1-20 User ’s Manual Introduction.
User ’ s Manual 2-1 TECRA M5 Cha pter 2 T he Gr and T our This chapter identifies the vari ous components of your computer . Become familiar with each component before you ope rate the computer . F ront with the display closed Figure 2-1 shows the computer ’s front with it s LCD display panel in the closed position.
2-2 User ’s Manual The Grand T our ■ T urn W iFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pa cemaker or medical device operation, possibly resulting in serio u s injury .
User ’ s Manual 2-3 The Grand T our Left side Figure 2-2 show s the computer ’s l e f t side . Figure 2-2 The left side of the computer Cooling vents Security lock slot PC card slot SD card slot PC card eject button ExpressCard slot ExpressCard eject button i.
2-4 User ’s Manual The Grand T our Keep foreign objects out of the ExpressCard slot and PC card slot. Never allow metal objects, such as screws, st aples and paper cl ips, to enter t he PC or keyboard. Foreign metal objects can create a short circuit, which can cause PC damage and fire, possibly resulting in serious injury .
User ’ s Manual 2-5 The Grand T our Right side Figure 2-3 show s the computer’s right side. Figure 2-3 The right side of the computer Slim Select Bay USB ports V olume control Serial port Microphone jack Headphone j ack Vo l u m e c o n t r o l Use this dial to adjust the volume of the stere o speakers and the stereo headphones.
2-6 User ’s Manual The Grand T our Back side Figure 2-4 shows the computer ’s back side. Figure 2-4 The back side of the computer DC IN 15V jack Link indicator (green) Video- out jack Modem jack LAN jack LAN active indicator (orange) Video- out jack Plug an S-Video cable into this jack for video-out.
User ’ s Manual 2-7 The Grand T our Under side Figure 2-5 shows the underside of the computer . Make su re the display is closed before turning o ver your computer . Figure 2-5 The underside of the computer LAN jack This jack lets you connect to a LAN.
2-8 User ’s Manual The Grand T our Battery lock Slide the battery lock to release the battery pack for removal. Battery p ack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes .
User ’ s Manual 2-9 The Grand T our F ront with the display open This section shows the computer with the LC D display panel open. Refer to the appropriate illustration fo r details. T o open the display , slide the display latch on the front of the LCD displa y panel and lift up.
2-10 User ’s Manual The Grand T our Display hinge The display h inge holds the LCD display panel at easy-to-view angles. Fingerprint Sens or Just by swiping the finger against the fingerprint sensor , the following functions will be enabled: ■ Logon to Windows and access a security- enabled homepage through IE (Internet Explorer).
User ’ s Manual 2-1 1 The Grand T our To u c h P a d A T ouch Pad located in the center of t he pal m rest is used to control the on-screen pointer .
2-12 User ’s Manual The Grand T our System indicators LEDs beneath icons, light when various computer operations are in progress. Figure 2-7 System indicators Do not put a magnetic obje ct clos e to the switch. The computer will automatically enter Hi bernation Mode and shut down even if the Panel Power Off features is disabled.
User ’ s Manual 2-13 The Grand T our K eyboar d indicators The figures below show the positi ons of the keypad overlay indicators and the Caps Lock indicator . When the Arrow mode indicator glows the keypad overlay lets you control the cursor . When the Numeric mode i ndicator glows the keypad overlay l et s you enter numbers.
2-14 User ’s Manual The Grand T our USB floppy disk driv e The USB floppy d isk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port.
User ’ s Manual 2-15 The Grand T our Optical disk driv es One of the followin g Optical disk drives is installed in the computer: CD- ROM, DVD-ROM, DVD-ROM&CD-R/RW and DVD Super Multi drives. An A T API inte rface controller is used for CD/DVD-ROM operation.
2-16 User ’s Manual The Grand T our D VDs ■ DVD-R, DVD+R, DVD-R DL and DV D+R DL discs can be written only once. The recorded data cannot be erased or change d.
User ’ s Manual 2-17 The Grand T our D VD-ROM&CD-R/RW drive The full-size DVD-ROM dri ve module lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs witho ut using an adaptor . D VD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CDs as well as run either 12 cm (4.
2-18 User ’s Manual The Grand T our AC ada ptor The AC adaptor can automatically adj ust to any voltage ranging from 100 to 240 volts and to a frequency of eithe r 50 or 60 hertz, enabling you to use this computer in almost any country /region. Th e adaptor converts AC power to DC power and reduces the voltage supplied to this comp uter .
User ’ s Manual 2-19 The Grand T our Always use the T oshiba AC adaptor that was provided with your PC and the T osh iba Battery Charger (that may ha ve been provided with your PC), or use T oshiba recommended alte rnate mo dels to avoid any risk of fi re or other damage to the PC.
2-20 User ’s Manual The Grand T our.
User ’ s Manual 3-1 TECRA M5 Cha pter 3 Getting Star ted This chapter provides basic information to get you started using your computer . It covers the follo wing topics: ■ Setting up your work sp.
3-2 User ’s Manual Getting S tarted General conditions In general, if you are comfortable, so is your compu ter , but read the following to make sure yo ur work site provides a proper environment.
User ’ s Manual 3-3 Getting S tarted ■ Leave ample venti lation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately . Such interference c ould cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.
3-4 User ’s Manual Getting S tarted Seating and posture Maintain a comfortable working post ure when using your PC where your body joints are naturally aligned to reduce stress on different p arts of your body .
User ’ s Manual 3-5 Getting S tarted Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or hea daches.
3-6 User ’s Manual Getting S tarted Strate gic R est Br eaks T ake short, strategically spaced rest breaks to avoid eye strain and body discomforts. For more specific recommendations on the safety a.
User ’ s Manual 3-7 Getting S tarted 1. Connect the power cord to the AC adaptor . Figure 3-2 Connecting the power cord to the AC adap tor (2-pin plug) ■ Always use the T oshiba AC adaptor th at w.
3-8 User ’s Manual Getting S tarted Figure 3-3 Connecting the power cord to the AC adaptor (3-pin plug) 2. Connect the AC adaptor ’s DC output plug to the DC IN 15V jack on th e back of the computer . Figure 3-4 Connecting the adaptor to the computer 3.
User ’ s Manual 3-9 Getting S tarted 2. While holding down the p alm re st with one hand so that the main body is not raised, lift the panel slowly . Adjust the angle of the panel to provide optimal clarity . Figure 3-5 Opening the LCD display panel T ur ning on the power This section describes how to turn on the power .
3-10 User ’s Manual Getting S tarted Star ting up for the first time When you first turn on the power , the computer ’s initial screen is the Microsoft Windows XP S tartup Sc reen Logo. Follow the on-screen directions for each screen. During setup, you can click the B ack button to return to the previous screen.
User ’ s Manual 3-1 1 Getting S tarted Benefits of standby The standby feature provides the following benefits: ■ Restores the previous working environment more rapidly than does hibernation. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System S tandby feature.
3-12 User ’s Manual Getting S tarted 3. Press the power button. This feat ure must be enabled. Refer to the Setup Actions tab in TO SHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver .
User ’ s Manual 3-13 Getting S tarted Benefits of Hibernation Mode The Hiberna tion Mode feat ure provides the followin g benefits: ■ Saves data to the hard disk when the computer automatically shuts down because of a low battery . ■ Y ou can return to your previo us working environment immediately when you turn on the computer .
3-14 User ’s Manual Getting S tarted Data save in Hibernation Mode When you turn off the power in Hib ernation Mode, the computer takes a moment to save current memory data to the hard disk.
User ’ s Manual 3-15 Getting S tarted R estoring the pr einstalled software fr om the Re c ove r y H D D About 2.5GB of hard d isk sp ace is reserved for recovery partition. When re-setting up your hard disk, do n ot change, delete or add partitions in a manner other than specified in the manual.
3-16 User ’s Manual Getting S tarted 4. A menu appears, follow the on-screen instructions..
User ’ s Manual 4-1 TECRA M5 Chap ter 4 Oper a ting Basics This chapter descri bes the basic operations of your computer a nd precautions when usin g it, as we ll as the handling of CD/DVD. T OSHIBA Dual P ointing De vice The computer is equipped with a dual point system: a T ouch Pad and an AccuPoint pointing stick.
4-2 User ’s Manual Operating Basics Using the AccuP oint T o use the AccuPoint, simply p ush it with your finger tip in the di rection you want to move the on-screen pointer . T wo buttons above the T ouch Pad work in the same way with the AccuPoint as they do wi th the T ouch Pad.
User ’ s Manual 4-3 Operating Basics 2. Position a new cap on the peg and press it into place. Using the Finger print Sensor This product has a fingerp rint utility inst alled for the purpose of enrolling and recognizing fingerprints.
4-4 User ’s Manual Operating Basics ■ Clean the sensor with a lint-free cloth. Do not use detergent to clean the sensor . ■ Avoid the following finger conditions for enrollment or recognitio n as they may result in fin gerprint en rollment errors or a drop in the fingerprint recognition success ra te ■ Soaked or swollen finger (e.
User ’ s Manual 4-5 Operating Basics Fingerprint Sensor Limitations ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. ■ A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration.
4-6 User ’s Manual Operating Basics Set Up Procedur e Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required au thentication data using the "User Enrollment" Wizard . 1.
User ’ s Manual 4-7 Operating Basics Fingerprint Authentication Procedure 1. S tart up the computer . 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe th e fingerprint on the sensor . If authentication is successful, the user will be logge d on to Windows.
4-8 User ’s Manual Operating Basics How to Enable Fingerprint Power-on Security Settings I t is necessary to first enroll your fingerprint with the Protector Suite QL application prior to enabling an d configuring the Fingerprint Power-on Security System.
User ’ s Manual 4-9 Operating Basics Fingerprint utili ty limitations TOSHIBA does not guarantee that the Fi ngerprint utility technology will be completely secure or error-free. TOSHIBA does not guarantee that the Fingerprint utility will accu rately screen out unauthori zed users at all times.
4-10 User ’s Manual Operating Basics Using the USB flopp y disk drive The USB floppy d isk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand To u r , for more information. It is supp lied as standard with some models and as an option with others.
User ’ s Manual 4-1 1 Operating Basics Changing Slim Select Bay modules This section explains how to change m odules in the Slim Se lect Bay . The illustrations show replacem ent of the optical disk drive with the Slim Select Bay HDD adaptor . Therefore, the text refers to those mo dules.
4-12 User ’s Manual Operating Basics Inser ting a module Insert the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the comp uter as shown below and press unti l the ejector clicks.
User ’ s Manual 4-13 Operating Basics Loading discs T o load CD/DVDs, follow the steps below and refer to figures 4-6 to 4-9. 1. When the computer ’s power is on, press the eject button to open the disc tray slightly . Figure 4-6 Pressing the eject button 2.
4-14 User ’s Manual Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray . Figure 4-8 Inserting a CD/DVD 4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base.
User ’ s Manual 4-15 Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. Figure 4-9 Closing the CD/DVD disc tray Re moving discs T o remove the CD/DVD, follow the steps below and refer to fi gure 4-10.
4-16 User ’s Manual Operating Basics 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remo ve CD/D VD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
User ’ s Manual 4-17 Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite the data. ■ We recommend the following manufacturers of CD-R and CD-R W media. Media quality can affect write or rewrite success rates.
4-18 User ’s Manual Operating Basics W hen writing or rewriting Note the following when yo u write or rewrite a CD-R or CD-R W . ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste as the original data wi ll be lost if the re is a write error .
User ’ s Manual 4-19 Operating Basics Impor tant messa ge Before you write or rewrite to CD-R /RW or DVD-R/-R DL/-RW/+R/+R DL/ +RW/-RAM discs, read and follow all setup and operating in structions in this section.
4-20 User ’s Manual Operating Basics ■ If the disc is poor in quality , dirty or damaged, writing or rewriting erro rs may occur . Be careful to check the disc for dirt or damage before you use it. ■ The actual number of rewrites to CD-RW , DVD-RW , DVD+RW or DVD- RAM is affected by the quality of the disc and the way it is used.
User ’ s Manual 4-21 Operating Basics ■ There are two types of DVD-R dis cs: authoring and ge neral use discs. Do not use authori ng discs. Only general use di scs can be written to by a computer drive. ■ Y ou can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed wi thout a cartridge.
4-22 User ’s Manual Operating Basics W hen writing or rewriting Please observe/consider the follo wing when you write or rewrite to a CD-R/ -RW , DVD-R/-R DL/-R W /-RAM or DVD+R/+R DL/+RW disc. ■ Do not perform any of the following actions when writi ng or rewriting: ■ Change users in the Wind ows XP operating system.
User ’ s Manual 4-23 Operating Basics ■ Y ou canno t back up DVD-ROM, DVD- Video, DVD-R/-R DL/-RW or DVD+R/+R DL/+RW to CD-R/R W usi ng the “Exact Copy” function of RecordNow!.
4-24 User ’s Manual Operating Basics DLA for T OSHIBA Note the following limitations when you use DLA: ■ This software supports only re writable discs (DVD+R W , DVD-RW , and CD-RW). It does not support DVD+R/+R DL, DVD-R/-R DL, and CD-R discs that are not rewritable.
User ’ s Manual 4-25 Operating Basics How to mak e a D VD-V ideo Simplified steps for making a DVD-V i deo from video data captured from a DV -Camcorder: 1. Click [S tart]-[All Programs] - [Inter Video WinDVD Creator2] - [InterVideo WinDVD Creator] to launch WinDVD Creator .
4-26 User ’s Manual Operating Basics ■ While recording video to DVD or tape, please close all other programs. ■ Do not run software like a screen saver because it can put a heavy load on the CPU. ■ Do not run communication applications like a mode m or a LAN.
User ’ s Manual 4-27 Operating Basics ■ If you use an over-used rewritable disc, the full fo rmatting might be locked. Please use a brand new disc. Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care.
4-28 User ’s Manual Operating Basics 7. Do not place heavy objects on your floppy disks. 8. Do not eat, smoke, or use eraser s near your floppy disks. Foreign particles inside the floppy disk’ s jacket can damage the magnetic surface. 9. Magnetic energy can destroy the data on your floppy disks.
User ’ s Manual 4-29 Operating Basics T o hear the voice from a microphone or the analog sound from the line input, disable the Mute bu tton in the Input Monitor , and then disable the Audio power management function descri bed below . Audio power management The audio controller can be powered down when the audio function is not used.
4-30 User ’s Manual Operating Basics R e gion selection T elecommunication regulations vary from one region to another , so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. T o select a region, follow the steps below .
User ’ s Manual 4-31 Operating Basics Open dialog box, if the modem and T elephony Current Location region code do not match. A warning dialog box is displayed if current settings for region code and telephony location are in correct. Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed.
4-32 User ’s Manual Operating Basics 2. Plug the other end of the modular cable into a telephone jack. Figure 4-12 Connecting the internal modem Disconnecting T o disconnect the internal modular cable , follow the step s bel ow . 1. Pinch the lever on the connector in the telephone jack and pull out the connector .
User ’ s Manual 4-33 Operating Basics W ireless LAN The Wireless LAN is compatible wit h other LAN systems based on Direct Sequence S pread S pectrum /Orthogonal Frequency Divisio n Multiplexing radio technology th at complies with IEEE802.1 1 Wireless LAN standard (Revision A, B or G).
4-34 User ’s Manual Operating Basics Bluetooth wireless technology Bluetooth™ wireless tech nology elimin ates the n eed for cables between electronic devices such as desktop co mputers, printers and mobile pho nes. Y ou cannot u se the built-in Bluetooth fu nctions and an optional Bluetooth SD card 3 simultaneously .
User ’ s Manual 4-35 Operating Basics 3. Multi User: On Windows XP , the use of Bluetooth is not supported in a multi-user environment. This mea ns that, when you use Bluetooth, other users logged onto th e same computer will no t be able to us e its Bluetooth functionality .
4-36 User ’s Manual Operating Basics LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). This section describes how to connect/disconnect to a LAN.
User ’ s Manual 4-37 Operating Basics 2. Plug one end of the cable into t he LAN jack. Press gently until you hear the latch click into place. Figure 4-13 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub co nnector . Check with your LAN administrator before connecting to a hub.
4-38 User ’s Manual Operating Basics Mo ving the computer The computer is d esigned for rugged durabil ity . Howe ver , a few simp le precautions taken when moving the computer will help ensu re trouble-free operation. ■ Before moving the computer , it recommends changing the function of HDD Protection.
User ’ s Manual 4-39 Operating Basics When vibration is detected, the follo wing messa ge is displayed, and the icon in the notifi cation area of the taskbar is changed to the protection state. This message is displayed until the OK button i s pressed or 30 seconds pass.
4-40 User ’s Manual Operating Basics T OSHIBA HDD Protection Proper ties Y ou can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window . T o open the window , click st art , point to All Programs , point to TOSH IB A , point to Utilities and click HDD Protection setting .
User ’ s Manual 4-41 Operating Basics Details T o open the Details window , click the Setup Detail button in the TOSHIBA HDD Protection Properties window .
4-42 User ’s Manual Operating Basics Hea t dispersal T o protect from overheating, the CPU has an internal temperature se nsor . If the computer ’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered.
User ’ s Manual 5-1 TECRA M5 Cha pter 5 T he K eyboar d The computer ’s keyboard layouts ar e compatible with a 101/102 -key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer .
5-2 User ’s Manual The Keyboard Function k eys: F1 … F12 The function keys (not to be confused with Fn ) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F1 2 are called function keys because they execute programmed functions when pressed.
User ’ s Manual 5-3 The Keyboard Press Fn + F10 or Fn + F1 1 to access the integrated keypad. When activated, the keys wi th gray markings on the b ottom edge become numeric keyp ad keys ( Fn + F1 1 ) or cursor control keys ( Fn + F10 ). Refer to the Keypa d overlay section in this chapter for more information on how to operate these keys.
5-4 User ’s Manual The Keyboard Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. T o restore the screen and original settings, press any key or press the Dual Pointing Device. If a screensaver passw ord is registered, a dialog box will appear .
User ’ s Manual 5-5 The Keyboard Display selection: Press Fn + F5 to change the acti ve display device. When you press these hot keys, a dialog box appears. On ly selectable devices will be displaye d. Hold down Fn and press F5 again to change th e device.
5-6 User ’s Manual The Keyboard Dual Pointing Device: Pressing Fn + F9 in a windows environment enables or disables the Dual Pointing Device function. When you press these hot keys, the current setting wil l change and be displayed as an icon. LCD screen resolution selection: Press Fn + Spac e keys to change the display resolution.
User ’ s Manual 5-7 The Keyboard W indows special k eys The keyboard p rovides two keys that have special functions in Windows: Windows logo key activates the sta rt menu and the other , the application key , has the same function as the secondary mouse button.
5-8 User ’s Manual The Keyboard Numeric mode T o turn on the Numeric mode, press Fn + F1 1 . The Numeri c mode indicator lights. Now try numeric data entry using the keys in figure 5-2.
User ’ s Manual 5-9 The Keyboard T emporarily changing modes If the computer is in Numeric mode , you can switch temporarily to Arrow mode by pressing a shift key . If the computer is in Arrow mode , you can switch temporarily to Numeric mode by pressing a shift key .
5-10 User ’s Manual The Keyboard.
User ’ s Manual 6-1 TECRA M5 Cha pter 6 P o wer and P o wer-Up Modes The computer ’s power resources incl ude the AC adaptor , batte ry p a ck and internal batteries. This ch apter gives details on making the most effective use of these resources including charging and changi ng batteries, tips for saving battery power , an d power up modes.
6-2 User ’s Manual Power and Power-Up Modes T able 6-1 Power conditions continued Power on Power off (no operatio n) AC adaptor connected 2nd battery fully charged • Operates • No char ge • LE.
User ’ s Manual 6-3 Power and Power-Up Modes T able 6-1 Pow er conditions continued *1 When the 2nd batte ry is not charging. *2 When the main battery is not charging.
6-4 User ’s Manual Power and Power-Up Modes Batter y indicator Check the Battery indicator to determine the status of the battery pack. The follo wing indicator light s indicate the battery status: .
User ’ s Manual 6-5 Power and Power-Up Modes Ba tter y types The computer has five types of batteries: ■ Battery pack ■ 2nd battery pack (option) ■ Extended capacity battery pack (option) ■ .
6-6 User ’s Manual Power and Power-Up Modes T o ensure that the battery pack maintains it s maximum capacity , operate the computer on battery power at leas t once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures.
User ’ s Manual 6-7 Power and Power-Up Modes High capacity batter y pack (option ) An optional High capacity battery pack is installable instead of a main battery pack. The connection method of High capacity battery p ack is the same as that of main battery pack.
6-8 User ’s Manual Power and Power-Up Modes Safety precautions Mishandling of battery packs can cause death, serious injury or property damage. Carefully obse rve the following advisories: Wa rn i n g : Indicates a potentially hazardous situation, which could result in death or serious injury , if you do not follow instructions.
User ’ s Manual 6-9 Power and Power-Up Modes 10. Ne ver subject a battery p ack to heat, and never store it or use it near a heat source. The battery pack could ignite or explode when heated or burned, possibly resulting in death or serious injury .
6-10 User ’s Manual Power and Power-Up Modes Caution 1. Use only battery packs recommended by T O SHIBA as replacements. 2. When installing a battery pack or before moving the PC, always make sure the battery pack is inserted co rrectly and securely .
User ’ s Manual 6-1 1 Power and Power-Up Modes Procedures T o recharge a battery pack while it is inst alled in the computer , connect the AC adaptor to the DC IN 15V jack and plug the other end into a working outlet. The Battery indicato r glows orange when the battery is being charged .
6-12 User ’s Manual Power and Power-Up Modes In such case, follo w the step s below . 1. Fully discharge the battery by leavin g it in the computer with th e power on until the power automatically shuts off. 2. Connect the AC adaptor to the DC IN 15V jack of the computer , and the AC adaptor into power outlet.
User ’ s Manual 6-13 Power and Power-Up Modes ■ How often and how long you use t he hard disk, optical disc and the floppy disk drive. ■ How much charge the battery contained to begin with. ■ How you use optional devices, such as a PC card, to which the battery supplies power .
6-14 User ’s Manual Power and Power-Up Modes Extending batter y life T o maximize the life of your battery p ack: ■ At least once a month, disconne ct the computer from a power source and operate it on battery power until the battery pack fully discharges.
User ’ s Manual 6-15 Power and Power-Up Modes 1. Save your work. 2. T urn the computer ’s power off. Make sure the Power indicator is off. 3. Remove all cabl es connected to the computer . 4. Close the LCD display panel and turn the computer upside down.
6-16 User ’s Manual Power and Power-Up Modes T o install a battery p ack, follow the steps below . 7. Insert the battery pack all the way to the end ( ➀ ). 8. Make sure that the battery p ack is securely in pl ace and the battery safety lock ( ➁ ) is in the lock position ( ).
User ’ s Manual 6-17 Power and Power-Up Modes ■ Delete (button) Click this button to delete a reg istered password. Before you can delete a password, you must first enter the current p a ssword correctly or insert a proper token. Please use BIOS Setup to change or delete the HDD Pa sswords or to set the HDD Master Password.
6-18 User ’s Manual Power and Power-Up Modes User T oken field ■ Create (button) Y ou can use an SD card token, instea d of entering the password. Af te r you have registered a password, insert an SD card in SD card slot and click Create . Y ou can use an SD card of any capacity , but it must be formatted correctly .
User ’ s Manual 6-19 Power and Power-Up Modes Star ting the computer by passw or d If you have already registered a password, there are three ways to start the computer: ■ Insert an SD card token before you turn on the computer . The computer will start normally , withou t displaying a password prompt.
6-20 User ’s Manual Power and Power-Up Modes W indo ws utilities Y ou can configure various setti ngs asso ciated with both S tandby Mode and Hibernation Mode within TOSHIBA Power Saver . Hot k eys Y ou can use hot keys Fn + F3 to e nter S tandby Mode and Fn + F4 to enter Hibernation.
User ’ s Manual 7-1 TECRA M5 Cha pter 7 HW Setup This chapter explains how to us e TOSHIBA HW Setup program to configure your computer , and prov ide s information on setting up the Execute-Disable Bit Capability and TPM.
7-2 User ’s Manual HW Setup General This window displays the BIOS version and co ntains two buttons: Default and About . Setup This field displays BIOS Version and date. Display This tab lets you customize your comput er’s display settings for either the internal LCD screen or for an extern al monitor .
User ’ s Manual 7-3 HW Setu p Boot Priority Boot Priority O ptions This option sets the priority for boo ting the computer . Select from the following settings: Y ou can o verride the settings and m.
7-4 User ’s Manual HW Setup T o change the boot drive, follow the steps below . 1. Hold down F12 and boot the computer . 2. The following menu will be di splayed with the following icons: Built-in HDD, Slim Select Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.
User ’ s Manual 7-5 HW Setu p HDD Priority Optio ns If more than one HDD is installed in the computer , this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. USB Memory BIOS Support T ype Set the type of the U SB memory as a startup device.
7-6 User ’s Manual HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an extern al keyboard to emulate the Fn key on the computer ’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set comb ination instead of the Fn key (PS/2 keyboard only).
User ’ s Manual 7-7 HW Setu p CPU This function lets you set the CPU ope rating mode. Dynamic CPU Frequency Mode This option lets you choose from the following settings: LAN Wake-up on LAN This feature lets the computer ’s power be turned on when it receives a wake-up signal from the LAN.
7-8 User ’s Manual HW Setup Device Config Device Configuration This option lets you set the device configuration. Parallel/Printer Some models are equipped with Paral lel/P rinter tab. This t ab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port.
User ’ s Manual 7-9 HW Setu p Configuring the Execute-Di sable Bit Capa bility and TPM The configurations for the Execute- Disable Bit Capability and TPM are carried out in the BIOS setup program. Star ting and Ending the BIOS Setup Pr ogr am S t arting the BIOS Setup Program 1.
7-10 User ’s Manual HW Setup Ending the BIOS Setup Program Save the changes and end the program. 1. Press the End Key . The “ Are you sure? (Y/N) The changes you made w ill cause the system to reboot .” message is displayed. 2. Press the Y key .
User ’ s Manual 7-1 1 HW Setu p Security controller The security controller settings are availabl e in SYSTEM SETUP (2/2) . TPM This setting enables or disables th e security controller known as TPM (T rusted Platform Module).
7-12 User ’s Manual HW Setup.
User ’ s Manual 8-1 TECRA M5 Cha pter 8 Optional De vices Optional devices can expand the computer ’s capabilities and it s versatili ty . This chapter describ es connection or installation of the.
8-2 User ’s Manual Optional Devices PC car d The computer is equipped with a PC card slot that can accommodate a T ype II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multif unction card and CardBus PC cards.
User ’ s Manual 8-3 Optional Devices Re moving a PC card T o remove the PC card , follow the steps below . 1. Open the Safely Remove Ha rdware icon on the T ask Bar . 2. Point to PC card and click. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly .
8-4 User ’s Manual Optional Devices 2. Press gently to ensure a firm connection. Figure 8-3 Inserting the ExpressCard 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configura tion in Windows to make sure it is appropriate for your ExpressCard.
User ’ s Manual 8-5 Optional Devices SD car d The computer is equi pped with an SD card slot that can accommodate Secure Digital flash memory cards wi th various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants that use SD card flash-memory .
8-6 User ’s Manual Optional Devices R emoving an SD card T o remove an SD card, follow the steps below . 1. Open the Safely Remove Hardware ic on on the T ask Bar . 2. Point to SD ca rd and click. 3. Push in the SD card and release it to pop the card out slightly .
User ’ s Manual 8-7 Optional Devices SD card car e ■ Do not write to a n SD card if the battery powe r is low . Low power could affect writing accuracy . ■ Do not remove an SD card while read/write is in progress. ■ The SD card is designed so that it can be inserted on ly one way .
8-8 User ’s Manual Optional Devices If you install a memory module that is not compatible with the computer , a beep will sound when you turn on the power. If the incompatible module is installed in slot A, there will be a long beep (1 second) followed by one short beep (0.
User ’ s Manual 8-9 Optional Devices 5. Slide your fingernail or a thin object under the cover and lif t it off. Figure 8-7 Removing the memory module cover 6.
8-10 User ’s Manual Optional Devices 7. Seat the memory module cover and secure it with one screw . Figure 8-9 Seating the memory module cove r 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.
User ’ s Manual 8-1 1 Optional Devices 7. Grasp the module by the sides and pull it ou t. Figure 8-10 Removing the memory module 8. Seat the memory module cover and secure it with one scre w . 9. Install the battery pa ck. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.
8-12 User ’s Manual Optional Devices Batter y char ger The battery charger provides a conv enient way to charge battery packs without requiring the use of your comput er .
User ’ s Manual 8-13 Optional Devices 8. With the hard disk drive i n a vertical position, lift it straight up and away from the connector . Figure 8-12 Removing the hard disk drive pack Installing the hard disk drive pac k T o install the hard disk drive pack, follow the steps below .
8-14 User ’s Manual Optional Devices Slim Select Bay HDD adaptor Y ou can increase your computer ’s data storage capacity by installing an additional hard disk drive in the Slim Select Bay . T o install an hard disk drive in the Slim Select Bay HDD adaptor follow the steps below .
User ’ s Manual 8-15 Optional Devices 3. Close the lid and slide the lock to the lock position. Figure 8-16 Closing the lid For details on inserting the Slim Select Bay HDD ada ptor in the computer ’s Slim Select Bay slot, refer to Chapter 4, Operating Basics .
8-16 User ’s Manual Optional Devices 3. T urn the monitor ’s power on. 4. T urn the computer ’s power on. When you turn on the power , the computer automatically recog nizes the monitor and determines whethe r it is color or monochrome.
User ’ s Manual 8-17 Optional Devices Changing the resolution If you want to change the resolution , follow the steps below . 1. Open Display properties and select the Settings tab . 2. Select Advanced . 3. Select the Adapter tab, then select List all mod e s .
8-18 User ’s Manual Optional Devices d. Click OK . e. Click OK in the Display Properties screen. i.LINK (IEEE1394) i.LINK (IEEE1394) is used for hig h -speed data transfer for a range of compatible .
User ’ s Manual 8-19 Optional Devices Connecting 1. Make sure the connectors are pr operly aligned and pl ug the i.LINK (IEEE1394) cable into the computer . Figure 8-19 Connecting the i.LINK (I EEE1394) cable into the computer 2. Plug the other end of the cable into the de vice.
8-20 User ’s Manual Optional Devices Advanced P or t R eplica t or III Plus In addition to the ports available on the comp uter , the Advanced Port Replicator III Plus provides serial port and separate ports for PS/2 mouse and PS/2 keyboard.
User ’ s Manual 8-21 Optional Devices Serial por t The serial connector can be used to connect to RS-232C comp ati ble devices. RS-232C compatible devices include the following: ■ Modem ■ Mouse T o connect a serial port, follow the steps below .
8-22 User ’s Manual Optional Devices.
User ’ s Manual 9-1 TECRA M5 Cha pter 9 T r oubleshooting TOSHIBA designed the computer for dur ability . Howe ver , should problems occur , following the procedures in this cha pter can help to determine th e cause. All readers should become familiar with this chapter .
9-2 User ’s Manual T r oubleshooting Preliminar y chec klist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious probl em. ■ Make sure you turn on all peripheral devices before you turn on the computer .
User ’ s Manual 9-3 T roubleshooting Har dware and system chec klist This section discusses problems ca used by your computer ’ s ha rdware or attached peripherals.
9-4 User ’s Manual T r oubleshooting Self test When the computer starts up, the self test will be run automati cally , and the following will be displayed : This message remains on the screen for a few seconds.
User ’ s Manual 9-5 T roubleshooting AC power If you have trou ble turning on the co mputer with the AC a daptor connected, check the DC IN indicator . Refer to Chap ter 6, Power and Power-Up Modes for more information. Battery If you suspect a problem with the battery , check the DC IN indicator as well as the Battery indicato r .
9-6 User ’s Manual T r oubleshooting Battery doesn’t charge when the AC adaptor is attach ed ( Battery or Slim Select Bay indicator does not glow orange.) If the battery is completely discharged, it will not begin charging immediately . W ait a fe w minutes.
User ’ s Manual 9-7 T roubleshooting Real Time Clock Passwor d K eyboar d Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard . Problem Pro cedure The following message is Displayed on the LCD screen: RTC battery is low or CMOS checksum is inconsistent.
9-8 User ’s Manual T r oubleshooting Inter nal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup , for more information. Har d disk driv e Problem Procedure No display Press hotkeys Fn + F5 to change the display priority , to make sure it is not set for an external monitor .
User ’ s Manual 9-9 T roubleshooting CD-ROM driv e Problem Procedure Y ou cannot access a CD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check wh ether the drive power is on. I f the power is off, click on the opt ical disk drive icon i n the task tray and turn on the power .
9-10 User ’s Manual T r oubleshooting D VD-ROM drive Problem Procedure Y ou can not access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently unt il it clicks into place. Check whether the drive power is on. If the power is off, click on the optical disk drive icon in the task tray and turn on the power.
User ’ s Manual 9-1 1 T roubleshooting D VD-ROM&CD-R/RW drive For more inform ation, refer to Chapter 4, Operating Basics . Problem Procedure Y ou cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place.
9-12 User ’s Manual T r oubleshooting D VD Super Multi drive For more information, refer to Chapter 4, Operating Basics . Cannot write correctly If you have tr ouble writing, ma ke sure you are observing the following precauti ons: ■ Use only media recommended by TOSHIBA.
User ’ s Manual 9-13 T roubleshooting USB floppy disk driv e For more inform ation, refer to Chapter 4, Operating Basics . SD card Refer also to Chapter 8, Optional Devices .
9-14 User ’s Manual T r oubleshooting PC car d Refer also to Chapter 8, Optional Devices . ExpressCar d Refer also to Chapter 8, Optional Devices . Dual P ointing De vice If you are using a USB mouse, also refer to the USB device section in this chapter and to your mouse documentation.
User ’ s Manual 9-15 T roubleshooting USB mouse The mouse poi nter moves too fast or too slow T ry cha nging the speed setting i n the mouse control utility . 1. Click start , click Control Panel , click Printers and Other Hardware and select Mouse icon.
9-16 User ’s Manual T r oubleshooting Finger print Sensor USB de vice Refer also to your USB device’s documentation. The mouse pointer moves erratically The mouse m ight be dirty . R efer to your mouse documentation for instructions on cl eaning. If problems persist, co ntact your dealer .
User ’ s Manual 9-17 T roubleshooting Memor y expansion Refer also to Chapter 8, Optional Devices , for information on installing memory modules. Sound system Refer also to documentation fo r your audio devices. Problem Procedure Beep sounds. (T wo beep s, a dash and a dot, for a defective memory module in slot A.
9-18 User ’s Manual T r oubleshooting Exter nal monitor Refer also to Chapter 8, Optional Devices , and to you r monitor ’ s documentation. i.LINK (IEEE1394) de vice Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on.
User ’ s Manual 9-19 T roubleshooting Modem Refer to Appendix C, A T Commands and Appendix D , S-registers . Problem Procedure Communication software can’t initialize modem Make sure the computer ’s internal modem settings are correct. Refer to Phone and Mo dem Properties in the Contro l Panel.
9-20 User ’s Manual T r oubleshooting LAN W ireless LAN If the following procedures do not restore LAN access, consult your LAN administrator . For more information on wireless communica tion, refer to Chapter 4, Operating Basics . Bluetooth For more information on wireless co mmunication, refer to Chapter 4, Operating Basics .
User ’ s Manual 9-21 T roubleshooting Printer Refer also to the Serial port sections in Chapter 8, Optional Devices , and to the troubleshooting and other rel evant se ctions in your printer and software documentation. An Advanced Port Replicator III Plus is equipped with a parallel port.
9-22 User ’s Manual T r oubleshooting Disposing of PC and PC batteries ■ Discard this PC in accordance with ordinances or rules of local regulations. For further information, contact your local government. ■ This PC contains rechargeabl e batteries.
User ’ s Manual 9-23 T roubleshooting ■ Consult the deale r you purchased your computer and/or so f tware from. They are your best sources for current information and support.
9-24 User ’s Manual T r oubleshooting United St ates of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA United Kingdom TOSHIBA Information Systems (U.K.) Ltd. TOSHIBA Court Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Eur ope (I.
User ’ s Manual 10-1 TECRA M5 Cha pter 10 Le gal F ootnotes This chapter states the Legal Footnote information applicable to T OSHIBA computers. In the text in this manu al, *XX is used to show which Legal Footnote description is rela ted to T OSHIBA computers.
10-2 User ’s Manual Legal Footnotes CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shut- down. This is a normal p rotective featur e designed to reduce the risk of lost data or damage to the product when used outside recommended conditions.
User ’ s Manual 10-3 Legal Footnotes LCD *5 Over a period of time, and depending on the usage of the computer , the brightness of the LCD scree n will de teriorate. This is an intrinsic characteristic of LCD technology . Maximum brightness is only available when operating in AC power mode.
10-4 User ’s Manual Legal Footnotes.
User ’ s Manual A-1 TECRA M5 A ppendix A Specifica tions This appendix summarizes the computer ’s technical specification s. Physical Dimensions En vironmental Requirements Weight (typical) 2.37 kilograms, co nfi gured with: 14.1” XGA, 512MB RAM, 40GB HDD, CD-ROM, Wireless LAN.
A-2 User ’s Manual S pecifications Power Requirements Built-in Modem AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.
User ’ s Manual A-3 S pecifications T ransmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedanc e 600 ohms ±30% Error correcting MNP class 4 and ITU-T V .
A-4 User ’s Manual S pecifications.
User ’ s Manual B-1 TECRA M5 A ppendix B Display Contr oller and Modes Display controller The display controller in terprets soft ware commands into hardware commands that turn particular parts on the screen on or of f. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel.
B-2 User ’s Manual Display Controller and Modes T able1 Vi deo modes (VGA) Video mode T ype Reso lution Character matrix (pels) Colors Scanni ng frequency V ertical ( H z ) 0, 1 VGA Te x t 40 × 25 .
User ’ s Manual B-3 Display Controller and Modes T able1 V ideo modes (VGA) continued Vide o mode Ty p e Resolution Character matrix (pels) Colors Scanning frequency V ertical (Hz) D VGA Grph 320 ×.
B-4 User ’s Manual Display Controller and Modes T able 2 V i deo modes (XGA mod el) * Only External Monitor ca n perform change of V ertical freq uency (Hz).
User ’ s Manual B-5 Display Controller and Modes T able 2 V ideo modes (XGA model) continued * Only External Monitor can perform change of V ertical frequen cy (Hz).
B-6 User ’s Manual Display Controller and Modes T able 2 V ideo modes (XGA model) continued * Only External Monitor ca n perform change of V ertical freq uency (Hz).
User ’ s Manual B-7 Display Controller and Modes T able 3 Vi deo modes (SXGA+ model) * Only External Monitor can perform change of V ertical frequen cy (Hz).
B-8 User ’s Manual Display Controller and Modes T able 3 V ideo modes (SXGA+ model) continued * Only External Monitor ca n perform change of V ertical freq uency (Hz).
User ’ s Manual B-9 Display Controller and Modes T able 3 V i deo modes (SXG A+ model) continued * Only External Monitor can perform change of V ertical frequen cy (Hz).
B-10 User ’s Manual Display Controller and Modes Pow er M i z e r PowerMizer is a graphics processor installed on this computer . The performance of PowerMizer can be config u red in three ways.
User ’ s Manual C-1 TECRA M5 A ppendix C A T Commands In most cases, you will not need to type A T commands manua lly . However , there might be some occasions when you will need to do so. This chapter describes A T comman ds for data mode. Fax and voice commands are taken care of by application software.
C-2 User ’s Manual A T Commands Bn Co mmunication standar d setting This command determines the communicati on st andard CCITT or Bell. B0 Selects CCITT V .22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default).
User ’ s Manual C-3 A T Commands Result Codes: OK n=0,1 ERROR Otherwise Hn Hook contr ol This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy . H0 Modem goes on-hook (default). H1 Modem goes off-hook.
C-4 User ’s Manual A T Commands Nn Modulation handshak e This command controls whether or not the local modem perfo rms a negotiated handshake at connection ti me with the remote modem when the communica tion speed of the two modems is dif ferent.
User ’ s Manual C-5 A T Commands T Select tone dialing This command instructs the modem to send DTMF ton es while dialing. Dialed digi ts are tone dialed un til a P command or dial modif i er is received.
C-6 User ’s Manual A T Commands Dial tone detect Disabled: The modem dials a call regard less of whether it detect s a dial tone. Enabled: T he modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
User ’ s Manual C-7 A T Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: OK n=0,1,2,3 ERROR Otherwise &F Load f actor y settings This command loads the configuratio n stored and programmed at the factory .
C-8 User ’s Manual A T Commands &Tn Self-test commands These tests can help to isolate probl ems if you experience periodic data loss or random errors. &T0 Abort. S tops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between th e modem and computer .
User ’ s Manual C-9 A T Commands N3 V .42, MNP , or buffered (default). The modem attempts to connect in V .42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V .
C-10 User ’s Manual A T Commands Result Codes: OK n=0,3 ERROR Otherwise.
User ’ s Manual D-1 TECRA M5 A ppendix D S-r e gister s S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answer s and how long to wait before it hangs up if a connection fails.
D-2 User ’s Manual S-registers S1 Ring counter This register is read only . T he value of S1 is incre mented with each ring. If no ring occurs over a si x-second interval, this reg ister is cleared. Range: 0-225 Default: 0 Units: rings S2 A T escape character (user defined) This register determines the ASCII values used for an escape sequence.
User ’ s Manual D-3 S-registers S5 Command line editing c har acter (user defined) This register sets the character recogniz ed as a backspace and pertains to asynchronous only . The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
D-4 User ’s Manual S-registers S8 Comma pause time This register sets the time, in seconds, that the modem mus t pause when it encounters a comma (,) in the dial command stri ng. In some countries/regions, S8 will set both wait before dialing and comma pause time.
User ’ s Manual D-5 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 =.
D-6 User ’s Manual S-registers A T command set r esult codes The following table shows the result codes. The result code summary Result Code Numeric Descr iption OK 0 Command exe cuted CONNECT 1 Mod.
User ’ s Manual D-7 S-registers *1: EC only appe ars when the Extended Result Codes configuration optio n is enabled. EC is replaced by one of the followi ng symbols, depending upon the error control meth od used: V .42bis - V .42 error control and V .
D-8 User ’s Manual S-registers.
User ’ s Manual E-1 TECRA M5 A ppendix E V. 9 0 The TOSHIBA internal modem uses V .90 technology . The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service prov ider that su pports V .
E-2 User ’s Manual V. 9 0 T able E-1 Result codes for a V .90 connection No. Result code Description 70 CONNECT 32000 EC* Connection at 32000 bps 72 CONNECT 36000 EC* Connection at 36000 bps 74 CONN.
User ’ s Manual E-3 V. 9 0 * EC stands for the Error Contro l method, which appears only when the extended result codes conf iguration option is ena bled. EC is replaced by one of the following symbols, dep endi ng on the error control method used. A T Command V42bis V .
E-4 User ’s Manual V. 9 0.
TECRA M5 User ’ s Manual F-1 A ppendix F Wi r e l e s s L A N Car d Specifica tions Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purcha sed ■ T ype of product Wireless communication is often subject to local radio regulations.
F-2 User ’s Manual Wireless LAN The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel la rger dist ances. ■ The range of your wi reless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
User ’ s Manual F-3 Wireless LAN *1 Factory-set default channels *2 Refer to the sheet Approved Countries/R egions for use for the countries/ regions that in which these chann el s can be used.
F-4 User ’s Manual Wireless LAN 108 5540 11 2 556 0 11 6 558 0 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825.
User ’ s Manual G-1 TECRA M5 A ppendix G Bluetooth wir eless tec hnolog y Inter oper ability Bluetooth TM Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless.
G-2 User ’s Manual Bluetooth wireless tec hnology Interoperability ■ Bluetooth wireless technol ogy is a new innovative technology , and TOSH IBA has not confirmed com p atibility of its Bluetooth TM products with all computers and/or equipment using Blueto oth wireless technology other than TOSHIBA portable computers.
User ’ s Manual G-3 Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless te chnology , like other radio devices, emit radio frequency electromagnetic energy .
G-4 User ’s Manual Bluetooth wireless tec hnology Interoperability L ‘ utilisation de ce dispositif est autorisée seulement aux cond itions suivantes: (1) il ne doit pas produire de brouillage et.
User ’ s Manual G-5 Bluetooth wireless technology Interoperability Caution: Exposure to Radio F r equency Radia tion The radiated output pow er of the Bluetoo th TM Card from T OSHIBA is far below the FCC radio frequen cy exposure limits.
G-6 User ’s Manual Bluetooth wireless tec hnology Interoperability 2. Indication The indicati on shown below appea rs on this equipment. (1) 2.4 : This equip ment uses a frequency of 2.4 GHz. (2) FH : This equipment uses FH-SS modulation. (3) 1: The interference range of this equipment is less than 10 m.
User ’ s Manual G-7 Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday: 10:00-17:00 T oll Free T el : 0120-15-1048 Direct Dial : 03-3457-4850 F AX : 03-3457-4868 De .
G-8 User ’s Manual Bluetooth wireless tec hnology Interoperability.
TECRA M5 User ’ s Manual H-1 A ppendix H A C P o wer Cor d and Connector s The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used.
H-2 User ’s Manual AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power co rd must be VDE type, H05VV -F .
TECRA M5 User ’ s Manual I-1 A ppendix I T OSHIBA Anti-theft Protection Timer This function sets the limit for the number of days during which you are able to bypass authentication for the BIOS, Hard Disk Drive and Fingerprint.
I-2 User ’s Manual TOSHIBA Anti-theft Protection T imer.
User ’ s Manual Glossary-1 TECRA M5 Glossar y The terms in this glossary cover topics related to this manual. Alternate naming is included for re ference.
Glossary-2 User ’s Manual Glossary IrDA : Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megab y.
User ’ s Manual Glossa ry-3 Glossary analog signal: A signal whose characteristics such a s amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. V oice communications are analog signals. ANSI: American National S tandards Instit ute.
Glossary-4 User ’s Manual Glossary bus: An interface for transmis sion of signals, data or electric power . byte: The re presentation of a single character . A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system.
User ’ s Manual Glossa ry-5 Glossary comp atibility: 1) The ability of one computer to accept and process da ta in the same manner as another com puter without modi fying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Glossary-6 User ’s Manual Glossary delete: T o remove data from a disk or other data storage device. Synonymous with erase. device driver: A pro gram that controls communication between a specific peripheral device and the computer . The CONF IG .SYS file contains device drivers that MS-DOS loads when you turn the computer on.
User ’ s Manual Glossa ry-7 Glossary escape: 1) A code (ASCII code 27), signalin g the computer that what follows are commands; used with periphe ral devices such as printers and modems.
Glossary-8 User ’s Manual Glossary hard disk drive (HDD): An electromechan ical device that reads and writes a hard disk. See also hard disk. hardware: The physical electronic and mechanical components of a computer system: typically , the comput er itself, external disk drives, etc.
User ’ s Manual Glossa ry-9 Glossary J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: T aken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power .
Glossary-10 User ’s Manual Glossary mode: A method of operation, for exam ple, the boot mode, S tandby Mode or the Hibernation Mode. modem: Derived from modulator/demodulator , a device that converts (modulates) digital data for transmission over tele phone lines and then converts modulated data (demodulates) to digital format where received.
User ’ s Manual Glossary-1 1 Glossary P p a rallel in terface: Refers to a type of information exchange that tran smits information one byte (8 bits) at a time. See also serial interfac e. pa ri t y: 1) The symmetrical relationship between two parameter val ues (integers) both of which are either o n or of f; odd or even; 0 or 1.
Glossary-12 User ’s Manual Glossary rest art: Rese tting a computer without tu rning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue . A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
User ’ s Manual Glossary-13 Glossary T terminal: A typewriter-like keyboard and CR T disp lay screen connected to the computer for data input/ou tput. TFT display : A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix tech nology with thin film transistor (TFT) to drive each ce ll.
Glossary-14 User ’s Manual Glossary.
User ’ s Manual Index-1 TECRA M5 Inde x A AC adaptor, 1-4 additional, 1-18, 8-11 connecting, 3-6 Advanced Port Replicator III Plus, 1-19, 8-20 ASCII characters, 5-9 B Battery charging, 6-10 extendin.
Index-2 User ’s Manual Index writing, 4-18 DVD-ROM, 2-5 DVD-ROM drive, 1-6, 9-10 DVD-ROM&CD-R/RW drive, 1-5, 1-6 location, 2-5 problems, 9-10, 9-11 using, 4-12 writing, 4-16 E Environment, 3-1 E.
User ’ s Manual Index-3 Index accessing, 7-1 Boot priority, 7-3 CPU, 7-7 device config, 7-8 display, 7-2 general, 7-2 keyboard, 7-6 LAN, 7-7 Parallel/Prin ter, 7-8 USB, 7-8 window, 7-1 I i.
Index-4 User ’s Manual Index USB, 1-8 Power button location, 2-9 conditions, 6-1 hibernation mo de, 3-12 indicators, 6-3 panel on/off, 1-13, 6-20 shut down m ode (boot mode), 3-10 standby mo de, 3-1.
User ’ s Manual Index-5 Index Sound system, 4-28 headphone jack, 1-9, 2-5 microphone, 2-2 microphone jack, 1-9, 2-5 mute hot keys, 5-3 problems, 9-17 Stereo speakers, 2-10 volume control, 2-5 Standb.
Index-6 User ’s Manual Index.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Toshiba TECRA M5 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Toshiba TECRA M5 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Toshiba TECRA M5, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Toshiba TECRA M5 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Toshiba TECRA M5, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Toshiba TECRA M5.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Toshiba TECRA M5. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Toshiba TECRA M5 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
