FR
Topcom logo
Notice d'utilisation officielle

Topcom 101

23 pages·1.5 MB·Thermomètre·PDF·ENITJA
Topcom 101
Table des matières 11 sections 1 INSTALLATION 14 · 2 BUTTONS 14 · 3 OPERATION TELEPHONE 15 · 4 SETTINGS 15 · … AfficherMasquer
Page 1 of the Topcom 101 user manual — 6 WARRANTY 17
Page 1 · cliquer pour agrandir
Page 1

1 INSTALLATION 14

2 BUTTONS 14

3 OPERATION TELEPHONE 15

3.1 Setting the ring volume 15

3.2 Flash (R) 15

3.3 Last number redial 15

3.4 Memory numbers 15

3.4.1 Programming a memory number 15

3.4.2 Calling a memory number 15

4 SETTINGS 15

4.2 Setting a language 15

4.1 Setting the clock 16

4.3 Setting the LCD contrast 16

5 OPERATION CALLER-ID 16

5.1 Receiving and saving calls 16

5.2 Message indications 16

5.3 Checking and erasing calls 17

5.3.1 Checking a call 17

5.3.2 Erasing a call 17

5.3.3 Erasing all calls from the call list 17

5.4 Recalling a memory number 17

5.5 Caller-ID 2nd call (Call Waiting) 17

5.6 Voice Mail indication (Message Waiting) 17

6 WARRANTY 17

Page 2 of the Topcom 101 user manual — 2 BUTTONS
Page 2 · cliquer pour agrandir
Page 2

1 INSTALLATION

You can use batteries or an AC adaptor to activate the telephone display. When you install the batteries, the telephone lines at the back of the phone have to be disconnected.

  • To insert the batteries, take the following steps :
  • Use a screwdriver or any other flat tool to open the battery compartment.
  • Put four 1,5V (AAA) batteries inside the battery compartment.
  • Close the battery compartment carefully.
  • To install the phone, you have to do the following :
  • Connect one end of the telephone cable to the Clip Phone 101 and the other end to the receiver.
  • Connect one end of the telephone line to the back of the phone “LINE” and the other end to the telephone line wall socket.

2 BUTTONS

Topcom 101 — 2 BUTTONS diagram (page 2)
Fig. 1
Topcom 101 — 2 BUTTONS diagram (page 2)
Fig. 2

1 Numerical buttons 2 Memory button 3 Memo button 4 Recall button 5 Erase button 6 Down button 7 Up button 8 Pause button 9 Mute button 10 Flash button 11 Redial button 12 Direct Memory button M1 13 Direct Memory button M2 14 Direct Memory button M3 15 Direct Memory button M4 16 Direct Memory button M5 17 Ring volume switch 18 Volume switch

Page 3 of the Topcom 101 user manual — 4 SETTINGS
Page 3 · cliquer pour agrandir
Page 3

3 OPERATION TELEPHONE

3.1 Setting the ring volume The ring volume switch is located on the right side of the phone. You can choose either high , low or OFF . Switch to the desired volume level. When you choose OFF the phone will not ring when a call comes in.

3.2 Flash (R) Press the Flash button to activate certain services, e.g. ‘Call Waiting’ (this service is only available if provided by your telephone provider), or to transfer phone calls when you are using a telephone exchange (PABX).

3.3 Last number redial When you want to call back the last dialled telephone number, press the Redial button as soon as you have picked up the receiver. The number will be dialled automatically.

3.4 Memory numbers You can program 15 telephone numbers (of max. 16 digits) in the memory under the memory locations 0..9 or M1..M5.

  • 3.4.1 Programming a memory number
  • Press the Memory button.
  • Enter the telephone number.
  • Press the Memory button again.
  • Press the memory location 0..9 (numerical buttons) or M1..M5.
  • 3.4.2 Calling a memory number
  • Pick up the receiver and press M1, M2, M3, M4 or M5; or press the Memo button first, followed by the memory location 0..9.
  • The programmed number will be dialled automatically.

4 SETTINGS

  • 4.1 Setting a language This phone can show the display text in 5 different languages. To set the desired language, take the following steps:
  • Press and hold the Erase and Up button simultaneously.
  • Release both buttons and press the Up button to scroll through the menu until “SET LANGUAGE” appears on the display.
  • Press the Erase button to confirm.
  • Use the Up or Down button to set the correct language.
  • Press the Erase button to confirm your choice.
Page 4 of the Topcom 101 user manual — 5 OPERATION CALLER-ID
Page 4 · cliquer pour agrandir
Page 4
  • 4.2 Setting the clock
  • Press and hold the Erase and Up button simultaneously.
  • Release both buttons and press the Up button to scroll through the menu.
  • Press the Erase button when “SET CLOCK” appears on the display.
  • Press the Erase button to confirm.
  • Use the Up or Down button to set the correct month, day, hour and minutes.
  • Press the Erase button each time to confirm.
  • 4.3 Setting the LCD contrast You can change the LCD contrast of this phone by :
  • Pressing and holding the Erase and Up button simultaneously.
  • Release both buttons and press the Up button until “SET CONTRAST” appears on the display.
  • Press the Erase button to confirm.
  • Press the Up button to go through the different possibilities.
  • Press the Erase button to confirm.

5 OPERATION CALLER-ID

5.1 Receiving and saving calls The Clip Phone 101 receives a call and shows the information sent by the local telephone provider. This information can consist of either the caller’s telephone number, the date and time; or the caller’s name, his telephone number, the date and time (Consult your telephone provider for the activation). The Clip Phone 101 can save 60 calls which can be reviewed later. It never saves the same call twice. When the memory is full, the oldest calls will be replaced by the new ones in the memory.

5.2 Message indications The following messages show the telephone status : NO CALLS There are no calls in the memory. UNKNOWN CALL The incoming call has been sent through by a telephone provider that doesn’t offer the Caller-ID service or their Caller-ID service is not connected to yours. PRIVATE CALL The caller has a private number, therefore the clip information is not visible on the display. LINE ERROR The clip information was interrupted during transmission of the data. END OF LIST There are no more calls. NO DATA SENT The number of the caller was interrupted during transmission. The number of identical calls received. The battery is almost empty. You have received a new call. The NEW/MSG LED blinks. You have received a message. The phone number has been called back.

Page 5 of the Topcom 101 user manual — 5 OPERATION CALLER-ID
Page 5 · cliquer pour agrandir
Page 5

5.3 Checking and erasing calls As soon as you have received new calls, the number will appear on the display and the ‘NEW/MSG’ LED blinks until all messages have been checked.

  • 5.3.1 Checking a call
  • Press the Up button to go to the next call. When you have gone through all calls, ‘END OF LIST’ appears on the display.
  • Press the Down button to look at the previous call.
  • 5.3.2 Erasing a call
  • P ress the Up button to go to the desired call.
  • P ress the Erase button briefly until ‘DELETE?” appears on the display.
  • P ress the Erase button again to erase the call shown on the display.
  • 5.3.3 Erasing all calls from the call list
  • P ress the Up button until a call from the call list is shown on the display.
  • P ress and hold the Erase button for 6 seconds until ‘DELETE ALL?’ appears on the display.
  • P ress the Erase button again and all calls will be erased.
  • 5.4 Recalling a memory number
  • Press the Up button to look up the desired number in the memory.
  • Pick up the receiver.
  • Press the Redial button and the selected number will be dialled automatically.

5.5 Caller-ID 2nd call (Call Waiting) When you’ve obtained a special service from your telephone provider that supports the function ‘Caller-ID 2nd Call’ and you receive a second call when you’re already on the phone, the telephone number of the second caller appears on the display. Consult your telephone provider on how to receive a 2nd call.

5.6 Voice Mail Indication (Message Waiting) When you obtained the Voice Mail system from your telephone provider that supports the function ‘Message Indication’, the text ‘MESSAGE WAITING’ appears on the display when a caller has left a message in your personal mailbox. As soon as you have received the message the display text disappears.

Remark : This function is only possible when you have a subscription to this service.

6 WARRANTY Warranty : 1 year. Contact your dealer. Attention : Do not forget to include your purchase invoice when you return the defect device.

Poser une question sur : Topcom 101

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Topcom 101

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Topcom 101 manuel PDF

23 pages·1.5 MB·Thermomètre·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…