Manuel d'utilisation / d'entretien du produit Venice 49cc du fabricant TN'G
Aller à la page of 33
V enice 49cc Owner ’ s Manual rev05-02.
T able of Contents Safety Notes .......................................................................... Page 2 Description ............................................................................ Page 3 Specifications ..........................
3 DESCRIPTION Seat Headlight Rear V iew Mirr o r 2 Cycle Mixing Oil Cover Muffler Throttle Rear Brake Lever Kick S tarter VIN Number Fr ont Brake Lever Speedometer Instrument Cluster Ignition Switch F.
4 Opening the Seat Insert the ignition key into the seat lock & turn to the right. Raise the rear of the seat to the upright position. Remove the ignition key . Closing the Seat Press the seat down to its normal position. Check the seat to make sure that it is locked in position.
5 T ransmission CVT Fuel Capacity 5.5 Liters / 1.5 Gals Rear Drive Oil T ype SAE20W -40 Rear Drive Oil Capacity Gear Box (100 cc) Fuel Mixing Oil Amsoil (Synthetic 2-stroke) Fuel Mixing Oil Capacity 4.
6 OPERA TING CONTROLS Ignition Switch (OFF) Power not applied to the lighting & ignition circuit. (ON) Power applied to the lighting & ignition circuit. Key cannot be removed from switch in this position. (LOCK) Steering mechanism locked into place.
7 Stop Switch Run Position Starter Button Stop Position S top Switch The Stop switch has two positions: Stop- Engine stops running. Run- Engine can run. S t art Button T urn the key in the ignition switch to on, hold the rear brake lever lightly , press the starter button & the starter motor will crank the engine.
8 Adding Fuel Note: T urn the engine off when refuelling Remove all source of flame from the area when refuelling. Unlock fuel cap, remove cap and add fuel. Capacity is approximately 1.5 gallons. No need to pre-mix oil with fuel. Oil will be added automatically during operation.
9 Adjusting the Brakes Rear Brake Adjustment Park the scooter on its center stand on a flat surface. Check the rear brake free play by measuring how far the tip of the brake lever will move until it begins to resist further movement. (See Figs 1 1 & 12) Brake lever at rest.
10 When turning the brake adjustment nut, make sure that the nut rests in the correct position when you remove the wrench. The concave surface of the nut must rest flush against the pivot pin. (See Fig 14) Make sure that the brake adjustment nut does not look like Fig 15! This brake has been adjusted incorrectly .
11 T ires T ire pressure should be checked frequently . The cold tire pressures are as follows: Front 25 PSI Rear 30 PSI T ires should be regularly checked for damage to the rim as well as damage to the tire itself. Look for any cuts, embedded nails, or other sharp objects.
12 OPERA TING THE SCOOTER S t arting the Engine (cold) T urn the ignition switch to the “ON” position. Hold the rear brake lever to apply rear brake. Set the stop switch to the “run” position (page 8). Do not open the throttle with your right hand.
13 Controlling the Speed The scooter ’ s speed is adjusted by the throttle control. Rotate the control counterclockwise slowly to increase the speed, and rotate the control clockwise to decrease the scooter ’ s speed. Using the Brakes The brakes work best when the front and rear brakes are applied at the same time.
14 S teering Mechanism Examine the front fork to be sure it is not bent or damaged. Raise & lower the front of the scooter and rock it from side to side while listening for any unusual sounds caused by bent front forks. Also turn the front steering axle to make sure that it is not binding or too loose.
15 Fig. 17 Once the 5 screws have been removed, the cover can be carefully opened to reveal the filter element located within. (See Fig 17) Fig. 18 Gently remove the filter element for inspection & possible cleaning. (See Fig 18) The air filter can be cleaned using compressed air and returned to service.
16 Battery The battery is a “maintenance free” type. It should not require electrolyte replacement. T o maintain a full char ge on the battery , it is best to use the kick starter for short trips. Always char ge the battery before storing the scooter for long periods of time.
17 3) After the fluid has stopped draining, replace the drain plug in the drain hole and tighten the plug with a wrench until it is snug. (Do not over- tighten the plug!) 4) Unscrew the rear drive oil filler cap located on top of the rear drive assembly beside the rear wheel.
18 Spark Plug Locate the spark plug by parking the scooter on it’ s side stand and looking underneath the chassis from the right side of the scooter . (See Fig 23) Pull off the spark plug cap, and remove the spark plug with the spark plug wrench provided in the tool kit.
19 Carburetor Adjustment Start the engine and let it idle for 5 minutes. Adjust the idle adjustment screw until the engine idles at 1500 +/- 100 RPM. (See Fig 25) Fig. 25 Idle Adjustment Screw Better access to the carburetor is obtained by raising the seat and remov- ing the screws which hold the luggage box in place.
20 3) Is the stop switch in the run position? Review the Start Switch section on page 8. 4) Is there a spark at the spark plug? Review the Spark Plug section on page 21 . 5) Is gas flowing to the carburetor? Raise the seat and remove the screws which hold the luggage box in place.
21 5) Are the fuses OK? After making sure the ignition is turned off, expose the battery wiring. (Review the opening the battery compartment procedure on page 8) Locate the fuse block (See Fig 27) Slide the spare fuse holder over the end of the fuse block and open the fuse block.
25 22 IGNITION MODULE REPLACEMENT If the ignition module must be changed, then use the following procedure. 1) Park the scooter on it’ s side stand and look underneath the scooter floorboard just behind the front wheel. Locate and remove the front screw which holds the cover unit in place.
23.
24 ROUTINE MAINTENANCE SCHEDULE SCOOTER STORAGE If your scooter will not be used for two months or more, you should store it properly to ensure that it will run reliably when you take it out of storage. It is also advisable to make any repairs to the scooter that it may need prior to storage.
W arranty CMSI, Inc., warrants to the first retail purchaser of all TN’G scooters from an Authorized CMSI Dealer and each subsequent owner that the vehicle is free from defects in materials and workmanship for the period stated in this warranty section.
T o perform warranty repairs on any T N’G product that qualifies for such repairs. The selling dealer shall sign the Acceptance Certificate and a Card of Delivery upon delivery of the vehicle.
W arranty T ime Period for 49cc scooter models Coverage Begins The date the motorcycle is delivered to the first retail purchaser . W arranty CMSI shall repair or replace, at its option, any part (including parts of the emission control system) that is found defective in material or workmanship under normal use for the applicable time period.
Y our Legal Rights These warranties give you specific legal rights. Y ou may also have other rights which vary from state to state. It is the responsibility of the owner to be aware of state laws which pertain to this issue in your particular state.
DISTRIBUT ORS LIMITED W ARRANTY – NEW MOTORCYCLE T N’G warrants to the first retail purchaser and subsequent purchasers of this vehicle that the motorcycle is free from defects in materials ands work- manship for the period stated in “W arranty T ime Period”.
DISTRIBUT OR’S LIMITED W ARRANTY - MOT OR- CYCLE TIRES W arranty T ime Period 90 days, or until the center tread is worn to a depth of 3/32" , whichever occurs first.
This W arranty Does Not Cover • T ires installed on non-CMSI Inc vehicles • T ires worn beyond the service limit specified in the appropriate Owners” Manual. • T ires rendered unserviceable by road hazard damage, such as impact breaks, punctures, cuts, or snags.
Parts installed by an Authorized CMSI/TN’G Dealer: Parts & Labor : No charge. Parts not installed by an Authorized CMSI/T N’G Dealer: Parts : No charge Labor : Y ou pay for removal/installatio.
CMSI Inc. 8146 304th Ave SE Preston, W A 98050 www .cmsiinc.com Rev05-2.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté TN'G Venice 49cc c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du TN'G Venice 49cc - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation TN'G Venice 49cc, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le TN'G Venice 49cc va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le TN'G Venice 49cc, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du TN'G Venice 49cc.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le TN'G Venice 49cc. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei TN'G Venice 49cc ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
