Manuel d'utilisation / d'entretien du produit 6100 du fabricant Texas Instruments
Aller à la page of 113
T ravelMate ® 6100 Series User ’ s Guide Notebook Computers frcvr.frm Page 1 Wednesday, January 22, 1997 3:34 PM Black Process Plate.
Copyright Copyright © 1997 Texas Instruments All Rights Reserved T ravelMate 6100 Series Notebook Computers User's Guide TI Part No. 9814483-0001 Original Issue: January 1997 Changes may be made periodically to the infor mation in this publication.
Notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pr otection against harmful inter ference in a residential installation.
Notice Use Conditions This part complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) this device may not cause har mful inter ference, and (2) this device must accept any inter ference received, including inter ference that may cause undesired operation.
Notice This equipment complies with Part 68 of the FCC rules. The following regulations apply to modems used within the United States and Canada: For USA Users: FCC Regulations An FCC compliant telephone cord and modular plug are provided with this equipment.
Notice the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most (but not all) areas, the sum of RENs should not exceed five.
Notice For Canadian Modem Users: The Industry Canada (IC) label identifies certified equipment. This certification means the equipment meets certain telecommunications network protective, operational, and safety requir ements. The department does not guarantee the equipment will operate to the user’s satisfaction.
notice.frm Page 8 Wednesday, January 22, 1997 3:57 PM.
Contents ix Contents Notice 5 Chapter 1: Using Documentation 1- 1 Printed Manuals. . . . . . . . . . . . . . . . . . . . . 1-2 Online Manuals . . . . . . . . . . . . . . . . . . . . . 1-3 Using the TravelMate Online Manual . . . . . 1-5 Deleting the TravelMate Online Manual .
Contents x Contents Chapter 6: Battery Operation 6-1 General Information about Batteries . . . . . 6-2 Charging Batteries . . . . . . . . . . . . . . . . . . . 6-4 Prolonging Battery Life . . . . . . . . . . . . . . . . 6-6 Responding to a Low Battery Condition .
Using Documentation 1-1 1 Using Documentation This chapter describes this manual and the other documentation that ships with your computer . It tells you how to use the T ravelMate ® Online Manual and how to delete those files from your hard disk drive if you are running short of space.
Printed Manuals 1-2 Using Documentation Printed Manuals Contents of the User ’ s Guide This manual provides the infor mation you need while the computer is tur ned off.
Online Manuals Using Documentation 1-3 Online Manuals Advantages of online documentation Online documentation has the following advantages. T ravelMate Online Manual The T ravelMate Online Manual provides you the infor mation you need while the computer is tur ned on.
Online Manuals 1-4 Using Documentation Other online documentation The following manuals are also available online. Manual Information Microsoft online manuals Full user information for the operating system Demo program Multimedia presentation of the features of your computer .
Using the TravelMate Online Manual Using Documentation 1-5 Using the TravelMate Online Manual Starting from Windows 95 Follow these steps to start the T ravelMate Online Manual from Windows 95. 1. Click on Start . 2. Point to T ravelMate Notebook Center .
Using the TravelMate Online Manual 1-6 Using Documentation browser loads the file containing the topic you have selected. To r eturn to the index fr om a topic, select the Back or Previous page function from your W eb browser . Printing current page or range of pages To print a page, select Print fr om the File menu.
Deleting the TravelMate Online Manual Using Documentation 1-7 Deleting the TravelMate Online Manual If you delete Although you can delete the online documentation, it is not recommended that you do so for the following reasons: • Most documentation for your computer is only available online.
Deleting the TravelMate Online Manual 1-8 Using Documentation How to delete in Windows NT To delete the T ravelMate Online Manual in Windows NT , follow these steps. 1. Click on Start . 2. Move to Settings and click on Taskbar . 3. Click on Start Menu Options tab.
Getting Started 2-1 2 Getting Started This chapter supplements the Installation Poster to help you install the computer for the first time. The chapter contains infor mation to help you make decisions during the setup process, details of the Windows 95 setup program, and a description of the multimedia demo program.
Getting Started 2-2 Getting Started Running the Demo Program 15 Contents of the demo program . . . . . . . . . 2-15 Running the demo . . . . . . . . . . . . . . . . . . 2-15 In Windows 95 . . . . . . . . . . . . . . . . . . 2-15 In Windows for Workgroups .
What You Need Before Starting Getting Started 2-3 What You Need Before Starting Read Safety Instructions The Safety Instructions for your computer are in printed for m so you can read them carefully before tur ning on your computer for the first time.
Running the Setup Program 2-4 Getting Started Running the Setup Program Which operating system to load The T ravelMate 6100 Series is available for use with several operating systems including: • W indows 95 • W indows for W orkgr oups and MS-DOS ® • W indows NT Note: There are two models of the T ravelMate 6100.
Running the Setup Program Getting Started 2-5 Windows 95. Check with your network administrator to deter mine whether Windows 95 is compatible. • Some software is incompatible with Windows 95.
Backing Up System Files 2-6 Getting Started Backing Up System Files After setting up the operating system, you should back up the operating system onto floppy disks. Y ou can make your backups immediately following setup or later . When you choose to back up your operating system on floppy disks, you will need several dozen floppy disks.
Backing Up System Files Getting Started 2-7 Maker screen. 3. Click on the program you want to back up. The disk maker prompts you to insert a floppy disk into the floppy disk drive. 4. Follow the prompts to back up the program. 5. Repeat steps 3 and 4 for each program in the list.
Loading Windows for Workgroups 2-8 Getting Started Loading Windows for Workgroups If you have decided to load DOS and Windows for W orkgroups, follow these steps. If you have decided to load Windows 95, skip this section. Loading PHDISK Loading PHDISK creates an area on your hard disk drive which stores infor mation upon disk shutdown.
Loading Windows for Workgroups Getting Started 2-9 Y ou are prompted to remove all disks fr om the floppy disk drives. 6. Remove any floppy disks from the floppy disk drive and select OK . Y our computer restarts. Creating Recovery Disk Y ou are prompted to create a r ecovery disk.
Loading Windows 95 2-10 Getting Started Loading Windows 95 If you have decided to load Windows 95, follow these steps: Loading PHDISK Loading PHDISK creates an area on your hard disk drive which stores infor mation upon disk shutdown. This partition is created automatically when you startup your computer for the first time.
Loading Windows 95 Getting Started 2-11 Y ou are prompted to remove all disks fr om the floppy disk drives. 8. Click OK to restart your computer . Configuring your system Since this is the first time Windows 95 has been started, the computer will advance through some initial file setup as it loads.
Loading Windows 95 2-12 Getting Started Y ou will be asked to reboot your computer for settings to take ef fect. 9. Select Ok . Y our computer is rebooted and Wi ndows 95 setup continues.
Loading Windows NT Getting Started 2-13 Loading Windows NT Windows NT Setup After gathering infor mation, you are ready to run the setup program. The first time you tur n on your computer , your system automatically runs the Windows NT Setup. The following steps help you through the Windows NT Setup.
Loading Windows NT 2-14 Getting Started 7. Type the password in the spaces next to both Password and Confir m Password, and click on Next . Y ou are given an opportunity to make changes before continuing. 8. Click Back to review what you have entered and make changes.
Running the Demo Program Getting Started 2-15 Running the Demo Program Note: The demo program does not run under Wi ndows NT . Contents of the demo program After completing setup, you can run a multimedia demo program. This program is entertaining and infor mative and includes the following infor mation.
Running the Demo Program 2-16 Getting Started 3. Move the cursor away from the boxes and click the primary mouse button once. An Exit button appears. 4. Click on the Exit button and select Ye s to exit. A window with software credits appears. 5. Select Click Here to exit.
Installing Internal Accessories 3-1 3 Installing Internal Accessories This chapter describes how to install the accessories that reside inside the computer . Preventing Damage from Static Electricity 2 If possible, use a grounding strap . . . . . . . .
Preventing Damage from Static Electricity 3-2 Installing Internal Accessories Preventing Damage from Static Electricity If possible, use a grounding strap Inter nal accessories, especially memory, are vulnerable to damage from static electricity while they are out of the computer .
Installing Memory Modules Installing Internal Accessories 3-3 Installing Memory Modules T ools required • Small, flat-blade screwdriver • W rist grounding straps ( recommended ) Maximum memory Y our computer has three slots for memory modules and comes with a 32-MB module standard in slot 2.
Installing Memory Modules 3-4 Installing Internal Accessories . eug-3.frm Page 4 Thursday, January 23, 1997 3:26 PM.
Installing Memory Modules Installing Internal Accessories 3-5 Removing the keyboard Follow these steps to remove the keyboard. 1. Insert a small, flat-blade screwdriver into the depression between the back of the keyboard and the base of the computer at the leftmost latch.
Installing Memory Modules 3-6 Installing Internal Accessories Inserting the memory module The system board has three slots for memory modules, one of which is already occupied by the factory-installed memory. Y ou can insert a 8-MB or 32-MB module in any of the slots.
Installing Memory Modules Installing Internal Accessories 3-7 Replacing the keyboard Follow these steps to put the keyboard back in place. 1. Insert the keyboard support. 2. Insert the four tabs on the bottom of the keyboard into the corresponding slots on the top cover .
Installing Memory Modules 3-8 Installing Internal Accessories 1. From the T askbar , select Start then Shut Down . 2. Select Restart the Computer in MS-DOS mode . 3. Click on Ye s . 4. Type PHDISK /D /F at the DOS prompt and press Enter . The Save to Disk partition is deleted.
Installing Memory Modules Installing Internal Accessories 3-9 4. When the Startup menu appears, select option 3, MS-DOS prompt with PC card support and press Enter . 5. Type PHDISK /C /F and press Enter . The Save to Disk file and partition are created.
Installing Modular Bay Accessories 3-10 Installing Internal Accessories Installing Modular Bay Accessories Using the modular bay By using the modular bay on your computer , you can modify your computer as your needs change. The modular bay can accept the following accessories.
Installing Modular Bay Accessories Installing Internal Accessories 3-11 Changing modules Follow these steps to change modules. 1. Tur n off the computer . 2. Press the release latch on the right side of the computer . 3. Lift the front of the computer slightly and pull out the accessory currently in the modular bay.
Installing Modular Bay Accessories 3-12 Installing Internal Accessories Note: Do not insert a cellular battery into the bay while a notebook battery is installed in the computer .
Installing PC Cards Installing Internal Accessories 3-13 Installing PC Cards Using PC cards The computer can accept two PCMCIA Type I or II cards or one Type III card. The following PC cards are available fr om Texas Instruments. Note: Use of the inter nal modem is recommended in units designed for U.
Installing PC Cards 3-14 Installing Internal Accessories 2. Insert the connector end of the PC card label-side up into the slot. 3. Gently push the PC card in as far as it can go. 4. Save the filler card for later use. Removing a PC card For ease of access your computer does not cover the slots for the PC cards.
Installing PC Cards Installing Internal Accessories 3-15 card. Refer to the T ravelMate Online Manual for instructions. Note : Computers running Windows NT , Windows for W orkgroups, and Unix ® , could require that you disable Plug and Play functionality to recognize new cards installed.
eug-3.frm Page 16 Thursday, January 23, 1997 3:26 PM.
Setting Up Your Desktop 4-1 4 Setting Up Y our Desktop Although your computer gives you high per for mance wherever you are, you can make your computer more usable as a workstation by setting up your desktop properly. This chapter describes your options while preparing your computer to function like a per manent workstation.
Setting Up Your Desktop 4-2 Setting Up Your Desktop Connecting an External Floppy Disk Drive 14 Required cables/connectors . . . . . . . . . . . 4-14 Connecting directly to computer . . . . . . . . 4-14 Connecting a Printer 15 Required cables/connectors .
Preparing To Install External Accessories Setting Up Your Desktop 4-3 Preparing To Install External Accessories Adding external accessories There are several re asons to add external accessorie s to y our computer .
Preparing To Install External Accessories 4-4 Setting Up Your Desktop A vailable accessories The following exter nal accessories are available for your computer .
Installing a DockMate Docking Solution Setting Up Your Desktop 4-5 Installing a DockMate Docking Solution Advantages of a DockMate Docking Solution A DockMate Docking Solution connects to the back of your computer and replicates the various ports on the computer .
Installing a DockMate Docking Solution 4-6 Setting Up Your Desktop adapters to fit the connectors on the DockMate. • Serial cables with 25-pin connectors require an adapter to fit a 9-pin connector • Older keyboards require an adapter to fit a PS/2 port Many connectors have screws attached to secure the connection.
Installing a DockMate Docking Solution Setting Up Your Desktop 4-7 Configuring the computer for a DockMate Follow these steps to configure the computer to work with a DockMate docking solution. 1. Tur n on the computer or restart the computer if it is already on.
Connecting a Keyboard 4-8 Setting Up Your Desktop Connecting a Keyboard Required cables/ connectors Keyboards almost always have a built-in cable. Most keyboards today have a PS/2 connector and can connect directly to the PS/2 port on the DockMate or on the computer .
Connecting a Pointing Device Setting Up Your Desktop 4-9 Connecting a Pointing Device Required cables/ connectors A mouse, glidepad, trackball, or other pointing device comes with a built-in cable. Most pointing devices have a PS/2 connector , although some may have a serial connector .
Connecting a Monitor 4-10 Setting Up Your Desktop Connecting a Monitor Required cables/ connectors Exter nal monitors usually have a built-in cable. Monitor cables use a standard connector , so an adapter is probably not required. Connecting to a DockMate Connect the cable to the video out port on the rear of the DockMate.
Connecting a Monitor Setting Up Your Desktop 4-11 Supported monitors Y our computer has built-in support for the following resolutions and colors. If your monitor has special requirements, follow the directions provided by the manufacturer of your monitor to install the correct driver .
Connecting a Monitor 4-12 Setting Up Your Desktop Refer to the T ravelMate Online Manual for instructions on using these utilities. Note: Exter nal monitors can use many resolutions that are incompatible with the screen on the computer . When this is the case, you cannot view both the computer screen and the monitor at the same time.
Connecting a Numeric Keypad Accessory Setting Up Your Desktop 4-13 Connecting a Numeric Keypad Accessory Required cables/ connectors The numeric keypad accessory comes with an integrated cable and is designed to connect to the keyboard PS/2 port. Y ou cannot use the numeric keypad accessory and an exter nal keyboard at the same time.
Connecting an External Floppy Disk Drive 4-14 Setting Up Your Desktop Connecting an External Floppy Disk Drive Required cables/ connectors With the addition of a special cable, you can connect the floppy disk drive module to the parallel port. This enables you to have another device in the modular bay and still use floppy disks.
Connecting a Printer Setting Up Your Desktop 4-15 Connecting a Printer Required cables/ connectors Most printers do not ship with a cable, so you may need to buy one. Most printers connect through the parallel port on the computer using a standard, Centronics™-type parallel cable.
Connecting Sound Equipment 4-16 Setting Up Your Desktop Connecting Sound Equipment T ypes of sound equipment Y our computer has a 16-bit sound card, stereo speakers, and a built-in microphone. By adding exter nal sound equipment, you can improve the quality of sound production and increase convenience.
Connecting Sound Equipment Setting Up Your Desktop 4-17 microphone audio in headphones/speakers eug-4.frm Page 17 Saturday, January 25, 1997 10:32 AM.
Connecting the Modem 4-18 Setting Up Your Desktop Connecting the Modem T ravelMate 6100 models developed for the U.S. and Canada contain an inter nal modem. Inter national customers use the PCMCIA card and port for modem connection. Description The inter nal modem supports the U.
Securing the Computer Setting Up Your Desktop 4-19 Securing the Computer Securing your computer The possibility of computer theft always exists. While the computer itself can be replaced, the data it contains may be irreplaceable. An investment of a few dollars and a few moments can prevent a disaster .
Feature Port 4-20 Setting Up Your Desktop Feature Port A feature port exists on your system. This port is provides the capability to expand your unit as further enhancements become available.
Installing Software 5-1 5 Installing Software Installing software on your computer is not much dif ferent than installing software on any computer . This chapter provides some guidance to help you select and install software. Selecting Software for the Computer Purchasing new software .
Selecting Software for the Computer 5-2 Installing Software Selecting Software for the Computer Purchasing new software When purchasing new software for your computer , check the carton and make sure .
Selecting Software for the Computer Installing Software 5-3 • If it works without any problems, you do not need to do anything else. • If it fails to work, you may be able to order an upgrade to the package that does work at only a fraction of the cost of a full software package.
Loading Software 5-4 Installing Software Loading Software Loading software from floppy disks Y our computer has a standard 3.5-inch floppy disk drive. If you are loading software fr om floppy disks, insert disk 1 into the floppy disk drive (Drive A) and follow the directions for installing the software.
Special Considerations Installing Software 5-5 Special Considerations Screen resolution Some software packages require a specific screen resolution (usually VGA) for optimal per for mance. If you have selected a different resolution, you may need to adjust the screen resolution before running the software.
eug-5.frm Page 6 Thursday, January 23, 1997 4:16 PM.
Battery Operation 6-1 6 Battery Operation When you are using your computer away from your desktop, you are usually running on battery power . This chapter shows you how to maximize your battery life. General Information about Batteries Battery characteristics .
General Information about Batteries 6-2 Battery Operation General Information about Batteries Battery characteristics The battery pack fits into either the primary battery slot on the left of the computer or in the modular bay on the right of the computer .
General Information about Batteries Battery Operation 6-3 Disposing of used battery Always dispose of used batteries in accordance with local regulations. Battery recycling is available in some areas. Ordering a spare battery The computer ships with a single battery.
Charging Batteries 6-4 Battery Operation Charging Batteries Determining current charge The battery has four green indicators that light, when the computer is on, to show the charge remaining in the battery. The following table shows how to interpret the indicators.
Charging Batteries Battery Operation 6-5 Note: If you have both batteries installed in the computer , it will take longer to charge the batteries, since the batteries charge in parallel.
Prolonging Battery Life 6-6 Battery Operation Prolonging Battery Life There are a number of actions you can take to r educe the rate at which your computer depletes the battery. By taking some or all of these actions, you can substantially increase the time you can operate on battery power before recharging the battery.
Prolonging Battery Life Battery Operation 6-7 Lowering inactivity timeouts Inactivity timeouts tur n off devices in the computer when you are not using them. Lowering the inactivity timeouts shortens the period of time the computer waits before tur ning off the device.
Responding to a Low Battery Condition 6-8 Battery Operation Save to disk During longer periods of inactivity, use the 0 V olt suspend mode (Fn-F2) to save battery charge. When you are operating the computer on battery power and the charge remaining is down to 20% of the maximum, the low-battery indicator blinks and an audible alar m sounds.
Responding to a Low Battery Condition Battery Operation 6-9 Replacing battery If you have a spar e, charged battery, you can do one of the following. • Insert the spare battery in the modular bay. • If you already have a battery in the modular bay, you can replace the primary battery without tur ning off the computer .
eug-6.frm Page 10 Thursday, January 23, 1997 4:33 PM.
Mobility 7-1 7 Mobility Although notebook computers can replace the desktop computer , the only reason to pay extra for a notebook computer is mobility. This chapter describes all the considerations to help you take advantage of your computer’s mobility.
Overview of Mobility 7-2 Mobility Overview of Mobility Disconnecting from the desktop No matter where you are taking your computer , you need to disconnect it from your desktop accessories. Moving around “Moving around” r efers to using your computer at dif ferent locations within the same building, for example, taking it with you to meetings.
Disconnecting from the Desktop Mobility 7-3 Disconnecting from the Desktop Disconnecting from a DockMate All DockMate Docking Solutions were designed to facilitate connecting and disconnecting the computer . Follow these steps if your computer is connected to a DockMate.
Moving Around 7-4 Mobility Moving Around Preparing the computer Y ou can carry the computer without tur ning off the power . Pr ess Fn-F3 (Suspend) to blank the screen, stop the hard disk drive, and save the current state of the computer . While in Suspend mode, the computer uses only minimal battery charge.
Taking the Computer Home Mobility 7-5 Taking the Computer Home Preparing the computer After disconnecting the computer from your desktop, follow these steps to prepare the computer for the trip home. 1. Remove all media from the drive in the modular bay.
Taking the Computer Home 7-6 Mobility • Changes in temperature and humidity can cause condensation. Allow the computer to retur n to room temperature, and inspect the screen for condensation before tur ning on the computer . If the temperatur e change is greater than 18°F (10°C), allow the computer to come to room temperature slowly.
Traveling with the Computer Mobility 7-7 Traveling with the Computer Preparing the computer Prepare the computer as if you were taking it home. Be sure that the battery in the computer is charged. Airport security frequently requir es you to tur n on your computer when bringing it to the gate area.
Traveling Internationally with the Computer 7-8 Mobility Traveling Internationally with the Computer Preparing the computer Prepare the computer as you would nor mally prepare it for traveling. What to bring with you Bring the following items with you.
Care and Troubleshooting 8-1 8 Care and T roubleshooting Regularly take time to check your computer and clean the screen, keyboard, and case to ensure tr ouble-free computing. If you do experience a problem, use the troubleshooting guide in this chapter to help you correct it quickly.
Cleaning the Computer 8-2 Care and Troubleshooting Cleaning the Computer Caution: Never use alcohol, benzene, thinner , or str ong chemical agents that could damage the computer case. Never apply liquid directly to the computer , only to a clean cloth.
Troubleshooting Tips Care and Troubleshooting 8-3 Troubleshooting Tips Errors at startup Error Corrective Action Computer does not come on when power switch is in the on position. • The battery may be low . Use the AC adapter and recharge the battery .
Troubleshooting Tips 8-4 Care and Troubleshooting Keyboard Event log indicates “Device not found” errors at startup This is normal. Windows NT is determining which optional devices are available before loading drives. The special function keys do not work.
Troubleshooting Tips Care and Troubleshooting 8-5 Battery External monitor Internal modem Docking Error Corrective Action Battery inserted, but LED’s not lit. Press Battery Status button. Battery Status button pressed, but indicators not lit. • Make sure AC adapter is plugged into computer and power outlet.
Troubleshooting Tips 8-6 Care and Troubleshooting PS/2 device connected to computer does not work with PS/2 device connected to DockMate Move PS/2 device on DockMate to rear PS/2 port. PS/2 Y cable does not work on DockMate Y cables only work when connected directly to a computer .
Troubleshooting Tips Care and Troubleshooting 8-7 Accessories Error Corrective Action Computer does not recognize the media device. Check the configuration in Device Manager . Ensure the correct drivers are installed. Computer does not recognize the accessory .
Troubleshooting Tips 8-8 Care and Troubleshooting Sound Internet Explorer does not work with Ethernet card. 1. Use DiskMaker to create Internet Explorer disk. 2. Set up network using Ethernet card or DockMate Net Ready . V erify you have network connection.
Troubleshooting Tips Care and Troubleshooting 8-9 Software Error Corrective Action Online manual gives Insufficient memory error in Windows for Workgroups. Close Internet Explorer and reopen Online Manual. Interactive demo leaves blank box in taskbar .
eug-8.frm Page 10 Saturday, January 25, 1997 11:17 AM.
Where To Get Help A-1 A Where T o Get Help T echnical assistance Customer support for your computer is available. Please have your serial number ready when you call. Ordering notebook products World W ide Web http://www.ti.com/notebook/index.html Feedback on manuals To comment on the manuals for your computer , send email to *PUBT@msg.
Texas Instruments Worldwide Sales Offices A-2 Where To Get Help Texas Instruments Worldwide Sales Offices Australia Texas Instruments Australia Ltd. Unit 1B, 11-17 Khartoum Road North Ryde, NSW 2113 Tel: (02) 99103100 Fax: (02) 98051186 Royal Domain Centre 14th Floor 380 St.
Texas Instruments Worldwide Sales Offices Where To Get Help A-3 Hong Kong Texas Instruments Hong Kong Ltd. 15th Floor, Tower 2, The Gateway 25-27 Canton Road Kowloon, Hong Kong Tel: (852) 29567288 Fax.
Texas Instruments Worldwide Sales Offices A-4 Where To Get Help Schweiz/Suisse Texas Instruments (Switzerland) Bernstr. 388 CH-8953 Dietikon Tel: (41) 01/745 58 58 Fax: (41) 01/742 06 16 Route de la Chocolatière 3 CH-1026 Echandens-Denges Tel: 021/701 53 54 Fax: 021/702 24 94 Singapore Texas Instruments Singapore (PTE) Ltd.
Index 1 Index A AC power 2-3, 3-7 accessories CD-ROM drive module 5-4 DockMate 4-4 DockMate Net Ready 4-4 DockMate Plus 4-4 errors 8-7 external 4-4 external monitor 4-4 floppy disk drive cable 4-4 ken.
Index 2 Index numeric keypad 4-13 pointing device 4-9 printer 4-15 sound equipment 4-16 speakers 4-16 contents of User’s Guide 1-2 D deleting demo program 2-16 online manual 1-7, 1-8 demo program co.
Index Index 3 M memory installing modules 3-3, 3-3–3-8 maximum 3-3 microphone, external 4-16 modem connecting 4-18 internal 4-18 modules Avatar drive 3-10 battery pack 3-10 CD-ROM drive 3-10 cellula.
Index 4 Index registering computer 2-9 removing floppy disk drive 6-7 running demo program 2-15 S Safety Instructions 2-3 save-to-disk 6-8, 6-9 screen adjusting brightness 6-6 cleaning 8-2 screen reso.
9814483-0001 bckcvr.frm Page 16 Thursday, January 23, 1997 5:18 PM.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Texas Instruments 6100 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Texas Instruments 6100 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Texas Instruments 6100, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Texas Instruments 6100 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Texas Instruments 6100, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Texas Instruments 6100.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Texas Instruments 6100. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Texas Instruments 6100 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.