Manuel d'utilisation / d'entretien du produit SCF418IL-R1K62BP du fabricant SUPER MICRO Computer
Aller à la page of 87
SCF418 Chassis Series USER’S MANUAL 1.0 S UPER ® SCF418BC-R1K62BP SCF418IF-R1K62BP SCF418IL-R1K62BP.
SCF418 Chassis Manual ii Manual Revision 1.0 Release Date: April 1 1, 2013 The information in this User ’s Manual has been carefully reviewed and is believed to be accurate.
iii Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SCF418 4U chassis. Instal - lation and maintenance should be performed by experienced technicians only .
SCF418 Chassis Manual iv Manual Organization Chapter 1 Introduction Chapter 1 describes components included with this chassis, and the main features of the SCF418 chassis. This chapter also includes contact information. Chapter 2 System Safety This chapter lists warnings, precautions, and system safety .
v Preface Appendix A Power Supply Specications Appendix B SAS-F418-B6 Backplane Specications Appendix C SAS-F418-B2R Backplane Specications.
SCF418 Chassis Manual vi T able of Contents Preface About This Manual ............................................................................................. iii Manual Organization ...............................................................
vii Preface Chapter 5 Chassis Setup and Maintenance 5-1 Overview ......................................................................................................... 5-1 5-2 Installation Procedures ................................................
SCF418 Chassis Manual viii Chapter 6 Rack Installation 6-1 Overview ......................................................................................................... 6-1 6-2 Unpacking the System ................................................
1-1 Chapter 1: Introduction Chapter 1 Introduction 1-1 Overview Supermicro's SCF418 "Fat T win" chassis is designed to optimize performance per W att and per dollar with up to eight independent hot-pluggable DP computing nodes, efciently organized into a 4U form factor .
SCF418 Chassis Manual 1-2 1-3 Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
1-3 Chapter 1: Introduction 1-4 Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required be - fore any warranty service will be rendered. Y ou can obtain service by calling your vendor for a Returned Merchandise Authorization (RMA) number .
2-1 Chapter 2: W arning Statements for AC Systems Chapter 2 Standardized W arning Statements for AC Systems 2-1 About Standardized W arning Statements The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury .
2-2 S UPER S ERVER "servername" User's Manual W arnung WICHTIGE SICHERHEITSHINWEISE Dieses W arnsymbol bedeutet Gefahr . Sie benden sich in einer Situation, die zu V erletzungen führen kann.
2-3 W arning Statements for AC Systems 안전을 위한 주의사항 경고! 이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수 있는 상태에 있게 됩니다.
2-4 S UPER S ERVER "servername" User's Manual Installation Instructions W arning! Read the installation instructions before connecting the system to the power source. W arnung V or dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.
2-5 Chapter 2: W arning Statements for AC Systems Circuit Breaker W arning! This product relies on the building's installation for short-circuit (overcurrent) protection.
2-6 S UPER S ERVER "servername" User's Manual Power Disconnection W arning 電源切断の警告 システムコン ポ ー ネン トの 取り 付 けまた は 取り外しの た .
2-7 Chapter 2: W arning Statements for AC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema.
2-8 S UPER S ERVER "servername" User's Manual Equipment Installation 機器の設置 ト レ ーニン グを受け認 定さ れた人だけが こ の装 置の 設 置、 交換、 .
2-9 Chapter 2: W arning Statements for AC Systems ア ク セ ス制限区域 こ のユニ ッ ト は 、 ア ク セ ス制限区域に 設置 さ れ る こ と を想定 し て い ま す 。 .
2-10 S UPER S ERVER "servername" User's Manual Battery Handling W arning! There is the danger of explosion if the battery is replaced incorrectly . Replace the battery only with the same or equivalent type recommended by the manufacturer .
2-1 1 Chapter 2: W arning Statements for AC Systems W arnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr . Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
2-12 S UPER S ERVER "servername" User's Manual W arnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle V erbindungen entfernt werden. ¡Advertencia! Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
2-13 Chapter 2: W arning Statements for AC Systems Backplane V oltage バッ ク プレ ーン の 電 圧 シ ス テ ムの稼 働中 は危険な電 圧 ま た は電 力が、 バ ッ ク プ レ.
2-14 S UPER S ERVER "servername" User's Manual Comply with Local and National Electrical Codes W arning! Installation of the equipment must comply with local and national electrical codes.
2-15 Chapter 2: W arning Statements for AC Systems Product Disposal W arning! Ultimate disposal of this product should be handled according to all national laws and regulations. יצראה למשחה יקוח םואית !הרהזא תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תביי ח ד ויצה .
2-16 S UPER S ERVER "servername" User's Manual W aarschuwing De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
2-17 Chapter 2: W arning Statements for AC Systems W arnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger , Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt.
2-18 S UPER S ERVER "servername" User's Manual W arning! When installing the product, use the provided or designated connection cables, power cables and AC adaptors. Using any other cables and adaptors could cause a malfunction or a re.
2-19 Chapter 2: W arning Statements for AC Systems Attention Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné. L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement ou un incendie.
2-20 S UPER S ERVER "servername" User's Manual Notes.
3-1 Chapter 3: Chassis Components Chapter 3 Chassis Components 3-1 Overview This chapter describes the most common components included with your chassis. Some components listed may not be included or compatible with your particular chassis model. For more information, see the installation instructions detailed later in this manual.
SCF418 Chassis Manual 3-2 Air Shroud The SCF418 chassis requires air shrouds for each node to direct the airow where cooling is needed. The air shroud will dif fer for different motherboards.
4-1 Chapter 4: System Interface Chapter 4 System Interface 4-1 Overview There are several LEDs on the control panel and on the drive carriers to keep you constantly informed of the overall status of the system. SCF418 models with rear I/O (left image below) include four control panels on the handles of the chassis which control each of the nodes.
SCF418 Chassis Manual 4-2 4-2 Control Panel Buttons • Power: The main power button on each of the four control panels is used to apply or remove power from the power supply to each of the four systems in the chassis. T urning off system power with this but - ton removes the main power , but keeps standby power supplied to the system.
4-3 Chapter 4: System Interface • NIC: Indicates network activity on either LAN1 or LAN2 when ashing. 4-4 Drive Carrier LEDs The SCF418 chassis uses SAS/SA T A drives. SAS/SA T A Drives Each SAS/SA T A drive carrier has two LEDs. • Blue: Each Serial A T A drive carrier has a blue LED.
SCF418 Chassis Manual 4-4 Notes.
5-1 Chapter 5: Chassis Setup and Maintenance Chapter 5 Chassis Setup and Maintenance 5-1 Overview This chapter covers the steps required to install components and perform mainte - nance on the chassis. The only tool you will need to install components and perform maintenance is a Phillips head screwdriver .
SCF418 Chassis Manual 5-2 5-3 Node Locations The SCF418 chassis contains eight individual motherboards in separate nodes. The nodes are available in a variety of congurations with 2.
5-3 Chapter 5: Chassis Setup and Maintenance 5-4 Removing Nodes from the Chassis Each of the eight individual nodes may be removed from the chassis. Note that when a node is removed from the chassis, the hard drives located in the node will shut-down.
SCF418 Chassis Manual 5-4 Figure 5-3: Front and Rear of the Node (Y our node may differ from the one shown in this illustration) Figure 5-4 SCF418BC-R1K62BP Node 5-6 Node Congurations Overview of the Node SCF418BC-R1K62BP Front of Node Rear of Node Six 2.
5-5 Chapter 5: Chassis Setup and Maintenance Figure 5-5: SCF418IFL-R1K62BP Node Figure 5-6: SCF418IL-R1K62BP Node SCF418IF-R1K62BP Front of Node Rear of Node T wo low-prole expansion cards T wo xed 3.5" hard drives SCF418IL-R1K62BP Front of Node Rear of Node One low-prole expansion card T wo xed 3.
SCF418 Chassis Manual 5-6 Figure 5-7: Hard Drives and the Corresponding Motherboards Node 4 Node: 8 Node 3 Node: 7 Node 6 Node 5 Node 2 Node 1 5-7 Nodes and Associated Hard Drives The SCF418 chassis contains eight individual motherboards in separate 1U nodes.
5-7 Chapter 5: Chassis Setup and Maintenance SCF418IL-R1K62BP Node 4 Controls two xed 3.5" HDDs D1-D2 Node 8 Controls two xed 3.5" HDDs H1-H2 Node 3 Controls two xed 3.5" HDDs C1-C2 Node 7 Controls two xed 3.5" HDDs G1-G2 Node 2 Controls two xed 3.
SCF418 Chassis Manual 5-8 Removing 2.5" Hard Drive Carriers from the Node 1. Press the release button on the drive carrier . This extends the drive bay handle. 2. Use the handle to pull the drive carrier out of the chassis. Figure 5-8: Removing a 2.
5-9 Chapter 5: Chassis Setup and Maintenance The 2.5" hard drives are mounted in the drive carrier to simplify their installation and removal from the chassis. These carriers also help promote proper airow for the drive bays. Figure 5-9: 2.5" Hard Drive Carrier Installing a 2.
SCF418 Chassis Manual 5-10 3. Install a new drive into the carrier with the printed circuit board side facing down so that the mounting holes align with those in the carrier . 4. Secure the hard drive by tightening all four screws. 5. Use the open handle to replace the drive carrier into the chassis.
5-1 1 Chapter 5: Chassis Setup and Maintenance Figure 5-13: Installing a 3.5" Hard Drive in the Drive Carrier Figure 5-12: Removing a 3.5" Fixed Hard Drive from the Node Installing and Removing 3.5" Fixed Hard Drives Removing 3.5" Fixed Hard Drives from the Node 1.
SCF418 Chassis Manual 5-12 Figure 5-14: Installing a 3.5" Fixed Hard Drive in the Node 6. Install a replacement drive into the hard drive tray and secure it to the tray with the screws previously set aside. 7. Secure the hard drive tray to the oor of the node with the screw previously set aside.
5-13 Chapter 5: Chassis Setup and Maintenance Figure 5-15: Removing the Screws at the T op of the Backplane (Y our node may differ slightly from the one shown in this illustration) 5-9 Removing and Installing the Backplane The SCF418 chassis backplane is located behind the hard drives and in front of the front system fans in each node.
SCF418 Chassis Manual 5-14 3. Remove the four screws securing the backplane to the node. 4. Lift the backplane up and out of the node. 1 5 Figure 5-16: Removing the Backplane from the Node (Y our node.
5-15 Chapter 5: Chassis Setup and Maintenance 1 2 1 3 Figure 5-17: Installing the Backplane (Y our node may differ slightly from the one shown in this illustration) Installing the Backplane Installing the Backplane into the Chassis 1.
SCF418 Chassis Manual 5-16 5-10 Installing the Motherboard Compatible Motherboards For the most up-to-date information on compatible motherboards and other parts, visit the Supermicro Web site at www .
5-17 Chapter 5: Chassis Setup and Maintenance Installing the Motherboard 1. Review the documentation that came with your motherboard. Become familiar with component placement, requirements, cautions, and cable connections.
SCF418 Chassis Manual 5-18 SCF418BC-R1K62BP Front of Node Rear of Node Eight 2.5" hot-swappable hard drives One Micro LP expansion card One low-prole expansion card SCF418IL-R1K62BP Front of Node Rear of Node One low-prole expansion card T wo xed 3.
5-19 Chapter 5: Chassis Setup and Maintenance 0.15 PCIE Slot Clip PCIE Slot Shield Figure 5-19: I/O Shield Conguration Installing Rear Low-prole Expansion Cards The following instructions are for chassis nodes in which the expansion cards are mounted in the rear of the node.
SCF418 Chassis Manual 5-20 Figure 5-20: Assembling the PCIE Slot Bracket and Cards Assembling the PCIE Slot Bracket Assembly Each node supports one expansion card. This expansion card must be plugged into a riser card, which in turn plugs into the motherboard.
5-21 Chapter 5: Chassis Setup and Maintenance Riser Card Bracket Mounting Screw Bracket Mounting Screws PCIE Slot Bracket Expansion Card Installing the PCIE Slot Bracket Assembly Into the Node Installing the PCIE Slot Bracket Assembly 1. Remove the PCIE slot cover and assemble the PCIE slot bracket assembly as described on the previous page.
SCF418 Chassis Manual 5-22 Figure 5-22: Installing the Micro LP Card (Y our node may differ slightly from the one shown in this illustration) Installing the Micro LP Assembly Into the Node Installing the Micro LP Card Assembly 1. Remove the screw securing the slot cover to the chassis and set the screw aside for later use.
5-23 Chapter 5: Chassis Setup and Maintenance PCIE Slot Clip PCIE Slot Shield Figure 5-23: PCIE Slot Conguration (Y our chassis and nodes may differ from those shown in this illustration) Installin.
SCF418 Chassis Manual 5-24 Figure 5-24: Assembling the PCIE Slot Bracket and Riser Card Assembling the PCIE Slot Bracket Assembly Each node supports one expansion card. This expansion card must be plugged into a riser card, which in turn plugs into the motherboard.
5-25 Chapter 5: Chassis Setup and Maintenance Figure 5-25: Installing the Riser Card and Bracket (Y our node may differ slightly from the one shown in this illustration) Figure 5-26: Installing the Expansion Card (Y our node may differ slightly from the one shown in this illustration) Bracket Mounting Screws 6.
SCF418 Chassis Manual 5-26 Figure 5-27: Installing the Air Shroud (Y our node may differ from those shown in this illustration) 5-12 Installing Air Shrouds Air Shrouds Air shrouds concentrate airow to maximize fan efciency . The SCF418 and SCF418L chassis require an air shroud in each node.
5-27 Chapter 5: Chassis Setup and Maintenance 5-13 Removing and Installing System Fans Removing and Installing Internal System Fans Removing Internal System Fans 1. Power down the system and remove the power cords from the rear of the power supplies as described in Section 5-2.
SCF418 Chassis Manual 5-28 Removing and Installing External System Fans Figure 5-30: Installing the External Fan (Y our node may differ slightly from the one shown in this illustration) Removing a Rear Exhaust Fan 1. Determine which node contains the failed fan and power down the node with the operating system.
5-29 Chapter 5: Chassis Setup and Maintenance The SCF418 chassis includes redundant 1620W power supplies. These power sup - plies are auto-switching capable. This enables the power supplies to automatically sense and operate at a 100v to 240v input voltage.
SCF418 Chassis Manual 5-30 Notes.
6-1 Chapter 6: Rack Installation Chapter 6 Rack Installation 6-1 Overview This chapter provides a quick setup to install the SCF418 chassis into a rack. Fol - lowing these steps in the order given should enable you to have the system installed within a minimal amount of time.
SCF418 Chassis Manual 6-2 6-4 W arnings and Precautions Rack Precautions • Ensure that the leveling jacks on the bottom of the rack are fully extended to the oor with the full weight of the rack resting on them. • In single rack installations, stabilizers should be attached to the rack.
6-3 Chapter 6: Rack Installation Rack Mounting Considerations Ambient Operating T emperature If installed in a closed or multi-unit rack assembly , the ambient operating tempera - ture of the rack environment may be greater than the ambient temperature of the room.
SCF418 Chassis Manual 6-4 6-5 Rack Mounting Instructions This section provides information on installing the chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean that the assembly procedure will differ slightly from the instructions provided.
6-5 Chapter 6: Rack Installation Figure 6-3: Attaching the Rails to a Rack Note: gures are for illustrative purposes only . Always install servers into racks from the bottom up. Installing the Rails on a Rack Installing the Rails 1. Adjust the length of both rails as described on the previous page.
SCF418 Chassis Manual 6-6 Figure 6-4: Installing into a Rack Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the oor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over .
A-1 Appendix A: Power Supply Specications Appendix A SCF418 Power Supply Specications This appendix lists power supply specications for your chassis system. SCF418BC-R1K620BP 1620W MFR Part # PWS-1K62P-1R AC V oltage 100 - 240V , 50 - 60Hz, 7.
SCF418 Chassis Manual A-2 Notes.
B-1 Appendix C: BPN-SAS-F418B6 Backplane Specications Appendix B BPN-SAS-F418-B6 Backplane Specications T o avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components.
B-2 SCF418 Chassis Manual B-3 An Important Note to Users All images and layouts shown in this user's guide are based upon the latest PCB revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this manual.
B-3 Appendix B: BPN-SAS-F418-B2R B-5 Front Connectors Figure B-1: Front Connectors 1. Main Power Connector (4-Pin): JP10 2. Main Power Connector (4-pin): JP13 3. Sideband Connector #1 (SB#1): JP52 4. Sideband Connector #2 (SB#2): JP54 5. Upgrade Connector: JP46 6.
B-4 SCF418 Chassis Manual 5 Upgrade Connector The upgrade connector , designated JP46 is a rmware upgrade port. Backplane Main Power 4-Pin Connector Pin# Denition 1 and 2 Ground 3 +5V 4 +12V B-6.
B-5 Appendix B: BPN-SAS-F418-B2R 1 3 12 13 24 25 36 37 48 A C A C A C A C A C A C A C A C A C A C A C A C 22 21 33 27 8 7 9 22 21 33 27 8 7 9 22 21 33 27 8 7 22 21 33 27 8 7 9 22 21 33 27 8 7 9 22 33 .
B-6 SCF418 Chassis Manual Notes.
C-1 Appendix C: BPN-SAS-F418-B2R Backplane Specications Appendix C BPN-SAS-F418B2R Backplane Specications T o avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components.
C-2 SCF418 Chassi Manual C-3 An Important Note to Users All images and layouts shown in this user's guide are based upon the latest PCB Revision available at the time of publishing. The card you have received may or may not look exactly the same as the graphics shown in this manual.
C-3 Appendix C: BPN-SAS-F418B2R Backplane Specications + + 1 2 3 4 7 7 DESIGNED IN USA 5V 12V #0 #1 REV 1.01 BPN-SAS-F418-B2R MH2 MH1 C45 JP10 J6 J5 c-5 Front Connectors Figure C-1: Front Connectors 1. Main Power Connector (4-pin): JP10 2. SAS Port #0: J5 3.
C-4 SCF418 Chassis Manual Backplane Main Power 4-Pin Connector Pin# Denition 1 and 2 Ground 3 +5V 4 +12V C-6 Front Connector and Pin Denitions 1 Backplane Main Power Connector The 4-pin connector , designated JP10 pro - vides power to the backplane.
C-5 Appendix C: BPN-SAS-F418B2R Backplane Specications BAR C ODE 22 21 33 27 8 7 9 22 21 33 27 8 7 9 A C A C J1 J2 D12 D13 ACT#0 ACT#1 SAS#1 SAS#0 C-7 Rear Connectors and LED Indicators Rear SAS/SA.
C-6 SCF418 Chassis Manual Disclaimer (cont.) The products sold by Supermicro are not intended for and will not be used in life sup- port systems, medical equipment, nuclear facilities or systems, airc.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté SUPER MICRO Computer SCF418IL-R1K62BP c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du SUPER MICRO Computer SCF418IL-R1K62BP - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation SUPER MICRO Computer SCF418IL-R1K62BP, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le SUPER MICRO Computer SCF418IL-R1K62BP va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le SUPER MICRO Computer SCF418IL-R1K62BP, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du SUPER MICRO Computer SCF418IL-R1K62BP.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le SUPER MICRO Computer SCF418IL-R1K62BP. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei SUPER MICRO Computer SCF418IL-R1K62BP ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
