Manuel d'utilisation / d'entretien du produit DP-1200/DP-1500/DP-2000 R59770175/01 du fabricant Barco
Aller à la page of 27
Xenon bulb lamp r eplac ement Install ation manual F or DP-12 00/DP-150 0/DP-20 00 R59770175/01 24/09/2008.
Barco NV Media and En t ertainment Division 11101 Trade Center Drive, Rancho Cordova, California 95670, USA Phone: +1 916 859-2500 Fax: +1 916 859-2515 E-mail: folsomsales@barco.com Visit us at the web: www.barco.com Barco n v Media & Entertainment D iv ision Noordlaan 5, B-8 520 Kuurne Phone: +32 56.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c onten ts T ABLE OF C ONTENTS 1 . X e n o n b u l b l a m p ..... ........ ........ ........ ........ .......... ........ ........ ........ ........ ........ ........ .... 3 1 . 1 I n t r o d u c t i o n ................. ..................
Tabl e of co nten ts 2 R59770175 XENON BULB LA MP REPLACEMENT 24/09/2008.
1. Xenon b ulb lamp 1. XENON BULB LAMP Safe ty Read all warnings and cautions at tentively . This to prevent per sonal injury while installing an xenon bulb lamp in the lam p house of the DP-1200/DP-1500/DP-2000 digital cinema projector .
1. Xenon b ulb lamp 1.1 Introduction Lamp & lamp house The xenon bulb lamp is delivered separately and ha s to be installed on site by a quali fi ed service technician. B A Image 1-1 A Lam p house. B X enon bulb lamp. Protective package The xenon bulb lamp is packed in a protec tive container or wrapped in a pr otective cloth.
1. Xenon b ulb lamp 1.2 Supported xenon bulb lamps Supported xenon bulb lamps (without lamp house) Lamp Ty p e Order i nfo Osram xenon bulb lamp of 4 kW 4kW DHP R9855937 Osram xenon bulb lamp of 3 kW .
1. Xenon b ulb lamp 6 R59770175 XENON BULB LA MP REPLACEMENT 24/09/2008.
2. Xenon b ulb lamp rep lacement pr ocess 2. XENON BULB LAMP REPLACEMENT PROCESS About this chapter This chapter descri bes how to replace the xenon bulb lamp in the lamp house.
2. Xenon bulb l amp replacement pr ocess 2.1 Remov al of the lamp house W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel. C AUTION : Lamp casing is very hot after operation. T o avoid burns, let the projector cool dow n for at least 15 minutes before proceeding to the lamp unit replacement.
2. Xenon b ulb lamp rep lacement pr ocess While starting up the projector , the electronics detect if a lamp is installed. If no lamp is installed, it is not possible to start up the projector .
2. Xenon bulb l amp replacement pr ocess 2.2 Re moval of the x e non bulb lamp W ARNING : DO NOT PER MIT UNAUTHORIZE D PERSONNEL TO PERFOR M OR A TTEMPT ANY PHASE O F XENON BULB LAMP HANDLING OR SERVICE. W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel.
2. Xenon b ulb lamp rep lacement pr ocess 3. Release the xenon bulb lam p fr om its socket by removing the hexagon socket head cap screw and plane washer as illustrated.
2. Xenon bulb l amp replacement pr ocess L N2 S W1 W2 N1 N1 N2 Image 2-6 7. Remove the cathode lamp adaptor (A) from the xenon bulb lamp (L) as illust rated. Us ea4m mA l l e nw r e n c ht or e l e a s et h e fi xation screw (S) of the adaptor . S L A Image 2-7 C AUTION : Expi red xenon bu lb lamps.
2. Xenon b ulb lamp rep lacement pr ocess 2.3 Installat ion of the xenon bulb lamp W ARNING : DO NOT PER MIT UNAUTHORIZE D PERSONNEL TO PERFOR M OR A TTEMPT ANY PHASE O F XENON BULB LAMP HANDLING OR SERVICE. W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel.
2. Xenon bulb l amp replacement pr ocess Image 2-8 3. Install the lamp cathode adapto r (A) upon the xenon bulb lamp (L) as illustrated. Use torq ue 2,5 Nm to fasten the fi xation screw ( S )o ft h ea d a p t e r . U s ef o rt h a tat o r q u ew r e n c hw i t ha5m m A l l e ns o c k e t .
2. Xenon b ulb lamp rep lacement pr ocess L N2 S W1 W2 N1 N1 N2 9 Nm Image 2-10 5. Remove the protective container or unwrap the prot ective cloth f rom the xenon bulb lamp. Warning: Ensure that you wear protective clothing, a f ull face shield and protect ive gloves.
2. Xenon bulb l amp replacement pr ocess Image 2-12 8. Reinstall the UV blocker ass embly as illustrated. Mak e sure that t he xenon bulb lamp is properly support ed by the lamp supporting mechanism in the centre of the UV blocker .
2. Xenon b ulb lamp rep lacement pr ocess 2,5 Nm A Image 2-15 1 1. Reinstall the side cover of the lamp house as illustrated. Note: Please ensure that the thumb screws turning wire s are fl ash with the cover or interf erence will occur while i nserting the lamp house into the projector .
2. Xenon bulb l amp replacement pr ocess 2.4 Installation of the lamp house W ARNING : This proc edure may onl y be perfor med by quali fi ed technical service perso nnel. C AUTION : Due to its hi gh internal pressure, the lamp may explode in either hot or cold states i f improperly hand led.
2. Xenon b ulb lamp rep lacement pr ocess While starting up the projector , the electronics detect if a lamp is installed. If no lamp is installed, it is not possible to start up the projector .
2. Xenon bulb l amp replacement pr ocess 2.5 Resetti ng the lamp parameters C AUTION : The “LAMP INFO” parameters which are stored on a chip MUST be updated after each installati on of an x enon b ulb lamp ins ide the lam p hous e. Neg l ecti ng this u pdate wi l l re sult in poo r perfo r m ance and sh ort lif e time o f the xenon bulb lamp.
2. Xenon b ulb lamp rep lacement pr ocess 2.6 Realignment of the lamp in it s re fl ector Each xenon bulb lamp installation req uires a realignment of the l amp in its re fl ec tor for op timal per formance of the xenon b u lb lamp in the D P-1200/DP-1500/ DP-2000 projector .
2. Xenon bulb l amp replacement pr ocess X LY Z Y LX Image 2-21 7. Fasten the X-axis lock thumb screw (ref LX image 2-21) and Y-axis lock thumb screw ( r ef L Y image 2- 21) . 8. Switch off the projector . 9. Reinstall the cover of the lamp compartment.
Index INDEX I Install 13, 18 Lamp house 18 Xenon lamp 13 Introduction 4 L Lamp 20–21 Realignment 21 Reset 20 Lamp house 8, 18 Install 18 Remove 8 R Realignment 21 Lamp 21 Remove 8, 10 Lamp house 8 X.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Barco DP-1200/DP-1500/DP-2000 R59770175/01 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Barco DP-1200/DP-1500/DP-2000 R59770175/01 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Barco DP-1200/DP-1500/DP-2000 R59770175/01, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Barco DP-1200/DP-1500/DP-2000 R59770175/01 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Barco DP-1200/DP-1500/DP-2000 R59770175/01, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Barco DP-1200/DP-1500/DP-2000 R59770175/01.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Barco DP-1200/DP-1500/DP-2000 R59770175/01. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Barco DP-1200/DP-1500/DP-2000 R59770175/01 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.