FR
Shure logo
Notice d'utilisation officielle

Shure MX300 Series

24 pages·881 KB·Microphone·PDF·ENNLJA
Shure MX300 Series
Table des matières 9 sections Microflex MX300 Series User Guide · Boundary Microphones · GENERAL · SECURING MICROPHONES TO A MOUNTING SURFACE (FIGURE 1) · … AfficherMasquer
Page 1 of the Shure MX300 Series user manual — GENERAL
Page 1 · cliquer pour agrandir
Page 1
Shure MX300 Series — Microflex  MX300 Series User Guide diagram (page 1)
Fig. 1 · Microflex MX300 Series User Guide

Microflex MX300 Series User Guide

Boundary Microphones

Low susceptibility to electromagnetic hum and RFI Programmable on/off switch and LED on/off indicator Logic input/output terminals for remote control or use

Shure MX300 Series — Microflex  MX300 Series User Guide diagram (page 1)
Fig. 2 · Microflex MX300 Series User Guide

with automatic mixers (MX392 models only) MODEL VARIATIONS

MX392 Models: Surface-mount microphone; in- cludes a programmable membrane on/off switch, log- ic input/output terminals, an on/off indicator LED, screw terminal connections, and attached untermi- nated cable. MX393 Models: Surface-mount microphone; in- cludes a programmable membrane on/off switch, an on/off indicator LED, and a miniature, three pin con- nector.

GENERAL

Shure Microflex MX300 Series microphones are surface- mounted electret condenser microphones designed primarily for mounting on conference tables, stage floors, and lecterns. Their high sensitivity and wide frequency range make them es- pecially suitable for picking up speech and vocals in sound re- inforcement and recording applications. Interchangeable car- tridges provide the installer with greater flexibility and make it possible to easily reconfigure microphone coverage as the need arises. The MX392 and MX393 models include an inter- nal preamplifier.

All Microflex microphones are available with any one of three interchangeable cartridges. The polar pattern of the original cartridge used in a particular microphone is indi- cated by the model number suffix:

C = Cardioid, S = Supercardioid, O= Omnidirectional

Cardioid (C). Recommended for general sound rein- forcement applications. Pickup angle (--3 dB) = 130.

Supercardioid (S). Recommended for sound reinforce- ment applications requiring narrow or more distant cover- age. Pickup angle (--3 dB) = 115.

MX300 Series microphones take advantage of the princi- ple that, at a barrier or boundary, the sound pressure level doubles. When placed near a sufficiently large boundary surface, the microphone has 6 dB higher sensitivity and approximately 3 dB greater direct-to-reverberant sound ra- tio. FEATURES

Omnidirectional (O). Recommended for recording or remote monitoring applications. Pickup angle (--3 dB) = 360. MICROPHONE PLACEMENT

To maintain the flattest possible low-frequency re- sponse and optimum rejection of background noise, place the microphone on a flat surface that is as large as pos- sible. The surface can be a floor, table, or lectern.

Flat frequency response across the vocal range for un-

colored sound Interchangeable cardioid, supercardioid, and omni-

directional cartridges that provide choices for applica- tions Sleek, low-profile design for unobtrusive appearance Balanced transformerless output for increased immunity

to noise over long cable runs

MICROPHONE APPLICATION AND SELECTION GUIDE ApplicationMounting SurfaceMicrophone to Cable ConnectorCable Output ConnectorPolar PatternMicroflex Model Sound reinforcement for speech and vocalsLectern, pulpit, stage floor, or conference tableHard Wired Hard Wired TA3F TA3FHard Wired Hard Wired XLR XLRCardioid Supercardioid Cardioid SupercardioidMX392/C MX392/S MX393/C MX393/S Recording or remote monitoring of speech and vocalsLectern, pulpit, stage floor, or conference tableHard Wired TA3FHard Wired XLROmnidirectional OmnidirectionalMX392/O MX393/O

27E2834 (CD) 2003, Shure Incorporated Printed in U.S.A.

Selecting a Cartridge

Page 2 of the Shure MX300 Series user manual — PAINTING THE MICROPHONE (FIGURE 2)
Page 2 · cliquer pour agrandir
Page 2

SECURING MICROPHONES TO A MOUNTING SURFACE (FIGURE 1)

12. Reconnect the wire leads to the screw terminals.
13. Use fine sandpaper to remove any paint that may have adhered to the bottom edges of the grille.
1. Remove the Phillips screw from the bottom of the microphone base, then remove the retainer.
2. Remove the grille and foam screen by carefully inserting a pointed tool into the edge of the grille and prying it open.
14. Reinstall the retainer, grille, foam screen, and Phillips screw.
3. Place the microphone in the desired location and, using a pencil, trace the location of the screw holes through the microphone. Then drill a starter hole for each supplied screw.

CHANGING THE MICROPHONE CARTRIDGE (FIGURE 3)

1. Remove the Phillips screw from the bottom of the microphone base, then remove the retainer.
4. Cover the rear two foam pads on the microphone with tape so that it slides more easily across the mounting surface.
2. Remove the grille and foam screen by carefully inserting a pointed tool into the edge of the grille and prying it open.
5. Install the two supplied screws in the desired location on the mounting surface.
3. Remove the Phillips screw from the cartridge retaining bracket, then remove the bracket.
6. Reinstall the grille, foam screen, and retainer, and secure them with the Phillips screw.
4. Use your fingers to unscrew the cartridge from the microphone assembly.
7. Using a knife or a razor blade, cut a slot into each of the two foam pads covering the slots below the screw holes on the bottom of the microphone.
5. Use your fingers to screw the replacement cartridge into place.
8. Position the microphone so that the screw holes fit over the screw heads. Then slide the microphone so that the screw heads are in the slots in the microphone base.
6. Reinstall the cartridge retaining bracket and secure it with the Phillips screw.
7. Reinstall the grille, foam screen, and retainer, then secure them with the Phillips screw.

PAINTING THE MICROPHONE (FIGURE 2)

1. Remove the Phillips screw from the bottom of the microphone base, then remove the retainer.

RE--ROUTING CABLE FOR BOTTOM EXIT (FIGURE 4, MX392 MODELS ONLY)

2. Lift off the retainer, grille, and foam screen. Then separate the foam screen from the grille.
1. Remove the Phillips screw from the bottom of the microphone base, then remove the retainer.
3. If using an MX393 model, disconnect the TA4F miniature 4--pin connector. If you are using an MX392 model, disconnect the wire leads from the screw terminals, untie the knot in the cable, and slide the cable out.
2. Carefully lift off the grille and foam screen, using a pointed tool or screwdriver.
3. Disconnect the wire leads from the screw terminals on the microphone printed circuit board.
4. Remove the rubber strain relief.
4. Untie the knot in the cable, and slide the cable out.
5. Place the supplied plastic paint shield over the exposed circuit board.
5. Remove the rubber strain relief from the inside of the microphone.
6. Place the supplied adhesive masking strip over the switch panel on the front of the base.
6. Insert the cable through the slot between the two screw holes, starting from the bottom of the microphone base.
7. Cover the connector opening on the microphone base with the supplied round rubber plug.
7. Tie a single overhand knot in the cable from inside the microphone. This will help prevent the cable from being accidentally pulled out.
8. Cleanse the surfaces to be painted with denatured alcohol or naphtha.
9. Carefully spray paint the microphone base and grille the desired color. To avoid filling grille holes, apply paint in a thin layer. Allow paint to dry thoroughly before reinstalling the grille and foam screen.
8. Connect the wire leads to the screw terminals on the microphone circuit board.
9. Insert the supplied round rubber plug in the unused cable exit hole.
10. If using an MX392 model, thread the cable through the base, then through the rubber strain relief.
10. Reinstall the grille, foam screen, and retainer, and secure them with the Phillips screw.
11. If using an MX392 model, tie a single overhand knot in the cable as near to the end of the cable jacket as possible. Then insert the rubber strain relief back into the cable exit hole.
11. Secure the microphone to the mounting surface. Refer to the “Securing Microphones to a Mounting Surface” paragraph.
Page 3 of the Shure MX300 Series user manual — MX392 LOGIC MODIFICATIONS
Page 3 · cliquer pour agrandir
Page 3

INTERNAL DIP SWITCH FUNCTIONS (FIGURE 5)

On/Off switch. To gain access to the logic terminals, remove the grille retainer screw, the grille retainer, foam screen, and grille, as shown in Figure 2.

All MX392 and MX393 models have internal DIP switches that allow the user to change the behavior of the microphone

SWITCH BEHAVIORLED BEHAVIORDIP SWITCH SETTINGS Push to Mute, Release to Talk (As Shipped)LED on when microphone is active Push to Talk, Release to MuteLED on when microphone is active Toggle: Push On/Push OffLED on when microphone is activeInitially Muted Initially Active Microphone Always Active (switch available for logic functions only)LED Always OFF

MX392 LOGIC TERMINAL DEFINITIONS (Figure 6)

LOGIC GND Terminal: Connects to the logic ground of an automatic mixer, switcher, or other equipment. Can be modi- fied to prevent ground loops.

MX392 LOGIC MODIFICATIONS

Open the microphone as shown in Figure 2. Isolating Logic Ground from Audio Ground

1. Remove jumper R40 from the top of the circuit board. 2. Make sure LOGIC GND terminal connects to the logic ground of the automatic mixer, switcher, or other equipment. Changing SWITCH OUT Terminal to Always Momentary

SWITCH OUT Terminal: Provides a TTL logic low when the membrane switch is pressed. This signal is available at all times for all switch settings. The Switch Out function pro- vides a momentary closure when S1 is Off and a latching clo- sure when S1 is On.

To accommodate interface equipment requiring momen- tary closure of the microphone (even when the desired mi- crophone function is latching on/off), proceed as follows: 1. Remove R45 from the top of the circuit board. 2. Reinstall R45 at location R46 on the top of the circuit board.

LED IN Terminal: Can be modified to remotely control the LED by flipping DIP switch S3 in the microphone to the ON position. As supplied, the LED IN terminal draws 5 Vdc. When this is shorted to the LOGIC GROUND terminal, the LED turns on.

SWITCH BEHAVIORUSER ACTION REQUIREDDIP SWITCH SETTINGS Switch Deactivated, Microphone Always ActiveShort LED IN terminal to LOGIC GROUND terminal LED Always ON Automatic Mixer Mode (MX392 models only)Connect SWITCH OUT signal to various logic inputs of automatic mixer for custom functions Connect mixer channel GATE OUT to microphone LED IN. LED on microphone turns on when its channel is gated onSwitch out is Switch toggles logic low while switch out to switch is logic low pressed
Page 4 of the Shure MX300 Series user manual — SPECIFICATIONS
Page 4 · cliquer pour agrandir
Page 4

SPECIFICATIONS

Logic Connections (MX392 Only)

All measurements taken with microphone mounted on a wooden surface 76.2 cm x 76.2 cm (30 in. x 30 in.). Frequency Response (Figure 7)

LED IN: Active low (≤1.0v), TTL compatible. Absolute maximum voltage: --0.7V to 50V. SWITCH OUT: Active low (≤0.5V), sinks up to 20mA, TTL compatible. Absolute maximum voltage: --0.7V to 24V (up to 50V through 3k). Power Requirements

50 to 17,000 Hz Polar Pattern (Figure 8)

Cardioid (MX392/C, MX393/C) Supercardioid (MX392/S, MX393/S) Omnidirectional (MX392/O, MX393/O) Output Impedance

11 to 52 Vdc phantom 2.0 mA current consumption Environmental Requirements

EIA Rated at 150 (180 actual) Sensitivity (at 1 kHz, open circuit voltage)

Operating Temperature Range: --18 C to 57 C (0 F to 135 F) Relative Humidity: 0 to 95% Dimensions (Figure 9) Certification

Cardioid Cartridge: --27.5 dBV/Pa (4.22 mV) Supercardioid Cartridge: --26.5 dBV/Pa (4.73 mV) Omnidirectional: --22.0 dBV/Pa (7.94 mV)

1 Pascal=94 dB SPL Maximum Sound Pressure Level (1 kHz at 1% Total Harmonic Distortion, 1 k load)

Eligible to bear CE Marking. Conforms to European EMC Directive 89/336/EEC. Meets applicable tests and performance criteria in European Standard EN55103 (1996) parts 1 and 2, for residential (E1) and light industrial (E2) environments. REPLACEMENT PARTS

Cardioid: 117.0 dB Supercardioid: 116.0 dB Omnidirectional: 111.5 dB Signal to Noise Ratio (referenced at 94 dB SPL)

Omnidirectional Cartridge R183 Supercardioid Cartridge R184 Cardioid Cartridge R185 12’ (3.7m) Cable 3-Pin Miniature Connector (TA3F) to male XLR C119

Cardioid71.0 dB Supercardioid: 72.0 dB Omnidirectional: 76.5 dB Equivalent Output Noise (A-weighted)
Cardioid23.0 dB Supercardioid: 22.0 dB Omnidirectional: 17.5 dB Dynamic Range

SHURE, the Shure logo, and MICROFLEX are registered trade- marks of Shure Incorporated.

94.0 dB Common Mode Rejection

45 dB minimum, 10 Hz to 100 kHz Switch Attenuation

50 dB minimum Preamplifier Output Clipping Level

--6 dBV (0.5 V) Polarity

Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output connector.

Poser une question sur : Shure MX300 Series

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Shure MX300 Series

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Shure MX300 Series manuel PDF

24 pages·881 KB·Microphone·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…