Manuel d'utilisation / d'entretien du produit 113.244530 du fabricant Sears
Aller à la page of 24
v For Future Reference ,9__ARS owners manual MODEL NO. 113.244530 VARIABLE SPEED 10-1NCH BAND SAW Serial Number. Model and serial numbers may be found on the back of the saw. You should record both model and serial number in a safe place for future use.
FULL ONE YEAR WARRANTY ON CRAFTSMAN BAND SAW If within one year from the date of purchase, this Craftsman Band Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERV- ICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
if any part is missing, bent, or broken in any way, or any electrical part doesn't work properly, turn the saw off andunplug the saw. REPLACE damaged, miss- ing, or failed parts before using the sawagain. MAINTAIN TOOLS WITH CARE. Keep the sawclean forbest andsafest performance.
Plan the way you will hold the workpiece from start to finish. Do not hand hold pieces so small that your fingers will go under the blade guard. Use jigs or fixtures to hold the work and keep your hands away from the blade. Avoid awkward operations and hand positions where a sudden slip could cause fingers or hand to move into the blade.
i motor specifications and electrical requirements This machine is designed to use, and is wired for oper- ation on 120 volts, 60 Hz., alternating current. CAUTION: A direct current motor is used in this I saw. Changes to the internal wiring will create a I fire hazard and may also create a shock hazard.
contents POWER TOOL WARRANTY ..................................... 2 SAFETY INSTRUCTIONS FOR BAND SAW ............. 2 GLOSSARY OF TERMS FOR WOODWORKING ..... 4 MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS ..........................................
A c D ITEM TABLE OF LOOSE PARTS A B C D Basic saw assembly .......................... Owners Manual ................................. Loose Parts Bag Containing the following parts: Wing Nut 1/4-20 x 5/8 ........................ 1 Screw, Truss Hd. 1/4-20 .
assembly An alternate method of mounting is to fasten band saw to a mounting board. The board should be of suf- ficient size to avoid tipping of saw while in use. Any good grade of plywood or chipboard with a 3/4" mini- mum thickness is recommended.
INSTALLING THE BLADE WARNING: Push the on-off knob off, lock with J padlock, and unplug saw before removing or I installing blade. I 1. Loosen the upper slide lock knob and position the guide assembly about half way between the table and the frame. Tighten the lock knob.
7. The upper wheel needs to be placed in its lowest position. Locate the tension lock knob on the back of the saw and turn it counterclockwise approximately two turns.
2. Continue to pull up on the tension assembly until it has moved two or three notches above where the blade first straightened out. Engage the teeth on the catch into the notches.
NOTE: Letting the blade teeth hit the blade guides while using the band saw will ruin the blade. The set of the teeth and the sharpened edge of the teeth would be damaged. Proper adjustment of the upper and lower blade guide assemblies will prevent this from happening.
7. Locate the bevel indicator and 10-32 x 3/8" long panhead screw in loose parts bag. 8. Use a #2 phillips screwdriver to attach the bevel indicator to the back of the frame, in the small recess below the trunnion, with the 10-32 x 3/8" screw.
getting to know your band saw Frame Tension Catch Cover Blade Guard Table 9 Wrench Holder 2 Upper Slide Lock Knob 6 Tracking Adjustment Set Screw 5 Tension Lock Knob 7 Sawdust Ejection Port 10 Speed C.
- ON-OFF KNOI_ a. To turn machine "ON", place fingers on Speed Control/On-Off Knob and pull out. NOTE: The motor will gradually come up to speed after machine is turned "ON", this is a normal condi- tion. b. To turn machine "OFF", push in Speed Control/On- Off Knob.
CHOICE OF BLADE AND SPEED Your band saw will cut a wide variety of material-wood, wood like products, non-ferrous met- als (brass, aluminum, copper) and ferrous metals (steel, iron). In order to obtain satisfactory results fol- low these general guide lines: 1.
Dress for safety. Any power saw can throw foreign objects into the eyes. This can cause permanent eye damage. Wear safety goggles (not glasses) that comply with ANSI Z87.1 (shown on package). Everyday eyeglasses have only impact resistant lenses. They are not safe- ty glasses.
basic band saw operation A band saw is basically a "curve cutting" machine. It is also used for straight-line cutting operations such as cross cutting, ripping, mitering, beveling, com- pound cutting, and resawing. It is not capable of doing inside cutting.
maintenance MOTOR/ELECTRICAL Frequently vacuum or blow out any sawdust from the motor. I WARNING: If the power cord is worn, cut, or I damaged in any way, have it replaced immedi- I ately, WARNING: To avoid fire or electrocution, reassemble electric parts with only approved service parts.
troubleshooting WARNING: For your own safety, Push on-off knob "OFF", lock-out switch and remove plug from power outlet before readjusting or aligning your band saw. TROUBLE Motor will not run. Blade does not run in the approximate center of the upper wheel.
repair parts FOR 10-INCH BAND SAW 113.244530 Always order by Part Number- Not by Key Number 5 2 6 3 6 4 3 FIGURE 1 Key Part No No. Description 1 2 4 5 6 7 820286 STD601103 817899 STD502502 820279 820281 820284 Guard Blade * Screw Pan Cr Ty 'q'T" 10-32 x 3/8 Screw Soc Set 1/2 Dog Pt.
repair parts _>, _ (Jr) / 22 o 'r" 0 O_ (_0 L'O €_4.
repair parts 0 oZ 09 U') • _J_ im t_O • IJU a. i.i. o c- o D.. ..- o (/) 1. 8 O_ _ O_ 0_0 m_ c_ 0g o o O0 o n- o O9 o 0 o E o n o o _J al z _ F- x: t--- m o COT N o_ N No m 23.
/ owners manual SERVICE MODEL NO. 113.244530 VARIABLE SPEED 10-1NCH BAND SAW HOW TO ORDER REPAIR PARTS VARIABLE SPEED 10-1NCH BAND SAW Now that you have purchased your lO-Inch Band Saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sears 113.244530 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sears 113.244530 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sears 113.244530, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sears 113.244530 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sears 113.244530, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sears 113.244530.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sears 113.244530. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sears 113.244530 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
