Manuel d'utilisation / d'entretien du produit PRECISION PRO 5500 du fabricant Scytek Electronic
Aller à la page of 52
PRECISION PR O 5500 VEHICLE SECURITY SYSTEM WITH REMOTE START PRECISION PR O 2200 REMOTE START ONLY PRODUCT MANUAL.
L i m i t e d L i f e t i m e W a r r a n t y This system is warranted to the original purchaser , to be free from defects in material and workmanship.
1. About Y our System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote T ransmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
The ScyT ek Precision 5500 Series is a Combination Vehicle Security and Remote Starting System that will have f eatures and functions that will be described in the following sections with an ASTERICK * The Precision 2200 Series is a Remote Start System only .
The 2-wa y Color remote transmitter is off ering increased range and confirmation of any activ ated feature. Page 1 Button 1 Arms and Locks* the system and when held for 3 seconds, activ ates the system’ s Panic feature. Button 1 also locks the doors when the system is in V alet Mode.
Press and hold Buttons 2 and 3 until pager progr am features are displayed. Select pager setting by pressing buttons 1 or 2 to highlight the pager . Press but ton 3 to select the pager . Setting Date & Time Select Time Date setting by pressing buttons 1 or 2 to highlight the f eature.
Page 4 - Precision Pro Use buttons 1 & 2 to highlight the time par ameter you wish to change, use buttons 3 & 4 to scroll up or down to chage the time. Save the changes by pressing but ton 5. Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the f eature.
Page 5 - Color Remote Return to Previous Screen Select Previous Screen by pressing buttons 1 or 2 to highlight the feature. Press but ton 3 to select it. Press and hold Buttons 2 and 3 until pager progr am features are displayed. Select system setting by pressing buttons 1 or 2 to highlight the pager .
Setting AutoStart Cold Temperature Threshold Select Cold T emp start setting by pressing buttons 1 or 2 to highlight the f eature. Press button 3 to select it. Use buttons 3 & 4 to scroll up or down to chage the temper ature threshold. Save the changes by pressing button 5.
Page 7 - Color Remote Select Clock Sync set ting by pressing buttons 1 or 2 to highlight the pager . Press button 3 to select the pager . Pager Clock Sync This feature synchronizes the pager clock to the security system time of a da y clock. Select P ager Clock Sync by pressing buttons 1 or 2 to highlight the f eature.
Page 8 - Color Remote Use buttons 1 & 2 to highlight Set Time press button 3. The security system responce. Start Time 2 This feature sets the system Autostart 2 time. Select Sytem Clock S ync by pressing buttons 1 or 2 to highlight the feature. Press but ton 3 to select it.
Pressing and holding transmit ter button 5 will scroll through sever al transmit ter programmable options - TEMPERATURE, ENABLE COLD START, ENABLE HOT START, VALET MODE, ENABLE AUTOSTART 1, ENABLE AUTOSTART 2. TEMPERATURE Check the temperature inside the vehicle 1.
Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to lockout the tr ansmitter against accidental transmission. Release Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to release the transmit ter from Lockout.
Time: time of day clock Date/Engine Run Timer: date, or engine run minute timer if remote start activ ated (20 min max). Battery Status: displays remaining battery life.
Standard Remote Transmitter Description The Precision 5500, 2200 Series is supplied with one 5-button R emote T ransmitter that is used to control the system’ s operations. Note : Using the optional PC or P ocket PC interface with the network softw are, it is possible to reconfigure the functionality of the tr ansmitter buttons.
Adding/Replacing Standard Remote Transmitters T o replace lost or stolen transmit ters or to add additional transmit ters into the system, have all desired transmit ters ready and follow the steps below . Note : Up to 4 one-wa y transmit ters can be programmed to oper ate the system.
2-way LCD Remote Transmitter Description The Precision 5500 and 2200 are supplied with a 2-wa y LCD remote transmitter , offering increased r ange and confirmation of any activ ated features. Page 1 Button 1 Arms* and Locks the system and when held for 5 seconds, activ ates the system’ s Panic feature.
3. Press and release Button 1 on the first tr ansmitter , then on the second transmitter . · The siren*/horn will chirp/honk once for every tr ansmitter learned. 4. T urn off the ignition key . 5. The siren*/horn will chirp/honk 3 times to indicate the system has exited programming mode.
T o set the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. Press Button 3 until the desired minute is displayed.
Precision - Page 17 CHP Set the siren*/horn confirmation chirps*/honks ON or OFF : 1. Press and hold Button 5 until the display shows CHP . ·The tr ansmitter will beep three times.
Page 18 - Precision 2. Release But ton 5. · The tr ansmitter will beep once. · The LCD panel will show Auto Start Hot T emperatur e setting. 3. Press and hold Button 5 until the display shows CON . 4. R elease Button 5. · The tr ansmitter will beep once.
Precision - Page 19 Remote Arming*/Locking The system monitors 5 independent areas ( zones ) while armed: doors, hood/ trunk, shock sensor , optional sensor input, and the network port for future expansion.* T o Arm* and Lock the System: 1. T urn off the ignition.
Page 20 - Precision * Tamper Alert If the system was triggered while awa y , the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition.
Precision - Page 21 Panic Mode In the event of an emergency , the transmitter’ s remote Panic feature can be used to instantly trigger the alarm*/panic feature. T o activate the P anic Mode: 1. Press and hold Button 1 for 5 seconds. · The alarm will sound.
Page 22 - Precision T o Emergency Override the system using the Code: 1. F ollow steps 1-3 above. 2. Press the override switch a number of times equal to the Disarm code chosen, and continue holding for 10 seconds on the last press. · The system will disarm.
Precision - Page 23 Remote Starting T o Remote Start the S ystem: 1. Be sure the system is not in V alet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. · The siren*/horn will chirp/honk 4 times.
Page 24 - Precision Pro Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours. 1. Timer Only Mode ( Oprates for 24 hour priod only) (factory def ault) The Automatic Start feature starts the vehicle automatically ev ery one or two hours and runs for the preset Run Time.
Precision Pro - Page 25 Model: Precision 5500-M Precision 2200-M 1- T ach wire must be connected , The system must learn RPM. 2- Hand brak e must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 28.
Page 26 - Precision E x t e n d e d F e a t u r e s Ignition Door Locking F or added safety , the Ignition Door Locking feature allows v ehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on.
Precision - Page 27 1. Thoroughly read and become familiar with the installation instructions bef ore beginning the installation. 2. R eview system contents: Main Unit 1 T wo-way 5 But ton LCD R emote.
Page 28 -Precision Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment.
Precision - Page 29 S y s t e m W i r i n g 6-Pin Starter Harness Pin 1 RED WIRE A : Main P ower Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply . R emo v e the fuse until the installation is complete and all wiring is check ed.
Precision Pro - Page 30 Page 30 - Precision Pin 11 BROWN WIRE : Siren Output (+) 3A. The Brown wire must connect to the siren’ s red wire. The Black siren wire must be grounded. Pin 12 VIOLET WIRE : Positiv e Door Input (+). Connect to the door switch circuit wire that shows +12V when the door is open.
Precision - Page 31 6-Pin White Connector: Located on the front of the main module. pin 1 VIOLET : Lock and unlock common input pin 2 BROWN: Unlock Normally Closed pin 3 BLUE: Unlock Output pin 4 WHITE: Lock Normally Closed pin 5 GREEN: Lock Output pin 6 N.
Precision Pro - Page 32 Jumper Selection Carefully separ ate the top and bottom halves of the main unit case. Once the cov er is removed, the parking light polarity jumper will be visible next to the parking light relay . Set the jumper for the correct polarit y output as described below , then reassemble the main unit case.
Precision Pro - Page 33 Page 33 - Precision Entering System Programming This system is compatible with both the LCD two wa y transmit ter or the standard transmitter , all system programming can be perf ormed using either one. T o enter System Progr amming: 1.
Page 34 - Precision Pro Precision - Page 34 Branch Feature Button 1 (default) Button 2 Button 3 1. Arm Mode Manual Arming P assive Arming 2. Auto Rearming Mode Disabled Enabled 3. Arming Chirps Siren Chirps On Siren & Horn Chirps On Silent 4. Ignition Door Locking On Off Set Override Code 5.
Precision Pro - Page 35 5. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors when the ignition is turned off . The Ignition Door Locking f eature may be progr ammed to unlock all doors or the driver’ s door only .
Page 36 - Precision Pro 14. Disarm with Auxiliary 1 . When selected, activ ating the Auxiliary 1 output (usually used to open the trunk) will disarm the alarm the system. 15. Aux 2 Auto Activate with Arm. When selected, the Auxiliary 2 output will activate when the system is armed.
Precision Pro - Page 37 26. Ignition 2 Relay Program. Selects one of three operating modes f or the Ignition 2 relay output: Ignition 2, Accessory 2, or Starter 2. 27 . Wait to Start Polarity input. Select positive or negative w ait to start input. 28.
Page 38 - Precision Pro Precision - Page 38 S y s t e m O p t i o n s S t a r t e r O n l y S e r i e s Branch Feature Button 1 (default) Button 2 Button 3 1 Lock/Unlock Chirps Siren Chirps On Siren &.
Precision Pro - Page 39 Programmable System Options The following is a description of the progr amming options of the system. Some of the program br anches control more than one option, and may require accessing a particular br anch number twice in order to program all desired f eatures.
Page 40 - Precision Pro 9. Auxiliary 3 Mode. Selects from momentary , 10 second timed, or latched operation for Auxiliary 3. Momentary operation pro vides an output for as long as the tr ansmitter button is pressed.(1-w ay remote only) Timed operation pro vides an output that turns on for 10 seconds each time the tr ansmitter button is pressed.
Precision Pro - Page 41 21. RPM Learn/Tach Monitor This dual program branch sets the engine mode f or Gas or Diesel, and learns the vehicle’ s RPM threshold. For installation into a diesel equipped v ehicle, first set the engine type to diesel before learning RPM.
Page 42 - Precision R e l a y D i a g r a m s P ositive Dome Light Activ ation Negative Dome Light Activ ation P ositive Horn Honk Negative Horn Honk Starter Defeat/Anti-Grind Negative Glow Plug.
Precision - Page 43 Negative T rigger R everse P olarity V acuum Adding Actuators F ollow the diagrams below f or connecting basic door lock systems. For T wo Stage door lock systems (separately unlocks driv er and passenger doors) see following pages.
Page 44 - Precision T w o S t a g e D o o r L o c k D i a g r a m s T wo Stage Negative T rigger T wo Stage P ositive T rigger The Precision 5500 and 2200 Series is equipped with a dedicated P assenger Unlock output allowing T wo Stage Door Lock operation.
Precision - Page 45 T w o S t a g e D o o r L o c k Diagrams c o n t ’ d T wo Stage R everse P olarity T wo Stage Adding Actuators.
FCC ID: OARRXAM2000 This device complies with P art 15 of FCC Rules. Operation is subject to the f ollowing two conditions: 1) This device may not cause harmful interference.
Starter doesn’t start and parking lights flash: 3 Times - Engine RPM not detected (check tach wire and/or perform tach learn procedure) Hood Trigger is active (hood is open, wire is shorted to groun.
ScyTek Electronics 11627 Cantara Street North Hollywood, CA 91605 www .scytek.net © ScyT ek Electronics 2006 Precision 8-10-06 W i r i n g D i a g r a m Manual Transmission Mode: These Wires Must be .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Scytek Electronic PRECISION PRO 5500 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Scytek Electronic PRECISION PRO 5500 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Scytek Electronic PRECISION PRO 5500, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Scytek Electronic PRECISION PRO 5500 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Scytek Electronic PRECISION PRO 5500, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Scytek Electronic PRECISION PRO 5500.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Scytek Electronic PRECISION PRO 5500. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Scytek Electronic PRECISION PRO 5500 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
