Manuel d'utilisation / d'entretien du produit SRT-8040P du fabricant Sanyo
Aller à la page of 54
INSTR UCTION MANU AL SR T -8960P SR T -8040P Real Time Vid eo Cassette Recor der English Real Time-Vide orecor der Deutsch Magnétoscope en temps ré el Français Videogra bado r en tie mpo re al Espa.
PRECA UTIONS WARNING: DO NOT E X POSE THE VCR TO DRIPPING OR SPLASHING, AND NEVER PUT ANY OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, O N TOP O F THE VCR . To avoid electrical shock , do not open the cabinet. Refer servicing to qualified personnel only.
PRECA UTIONS Location For safe operation and satisfactory performanc e of your VCR, keep the following in mind when selecting a place for its installation: œ Shield it from direct sunlight and keep it away fr om sources of intense heat. œ Avoid dusty or humid places.
CONTENTS PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LOCATIONS OF CONTROLS AND INDICATORS .
LOCA TIONS OF CONTR OLS AND INDICA T ORS Front Panel 1 Digital display panel 2 Cassette loading slot 3 PLAY button REC CHECK button 4 STILL/PAUSE button 5 MENU button SHUTTLE HOL D button 6 SHUTTLE ri ng 7 JOG dial 8 SEARCH button MENU EXIT button 9 STOP button F EJECT button G TRACKING + button V.
LOCA TIONS OF CONTRO LS AND INDICA T ORS Digital Display 1 Operation Indicators œ They display the actual operation mode. Operation Mode Indicator Record (REC) Record pause (REC PA USE) Playback ( PL.
LOCA TIONS OF CONTRO LS AND INDICA T ORS [With the RS-485/232C i nterface board] œ Display when set to RS-485 œ Display when set to RS-232C œ Data transfer speed setting display œ Address setting disp lay (RS-485 only) 3 , 6 Mode display œ Day/Time search setting display 5 Power failure indicator Lights after a power failure.
LOCA TIONS OF CONTRO LS AND INDICA T ORS Back Panel (With the RS-485/232C interface board) 1 VIDEO OUT (video output) jack 2 VIDEO IN (video input) jack 3 AUDIO OUT (audio output) jack 4 AUDIO IN (aud.
CONNECTIONS Connect the video camera and TV monitor as shown in the figure below. NOTE: Before making the connections, make sure the devices are disconnected from the power outlet.
ON-SCREEN MENU Main Menu To access on-screen menu 1 Press the STANDBY/ON button. 2 When no menu is displayed on-screen, pres s the MENU button. ø The MAIN MENU appears. MAIN MENU <MAIN@MENU> 1.LANGUAGE/CLOCK@SET 2.DISPLAY/SW@OUT@SET 3.GENERAL@SET 4.
ON-SCREEN MENU WARNING OUT/CONTRO L SET menu <WARNING@OUT@SET>SET@UP ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N MECHA.PROBLEM@@@@Y VIDEO@LOSS@@@@@@@Y CLOG@DETECT.
SETTING THE LANGU A GE AND CLOCK Language Setting English, French, Spanish, P ortuguese, German, Italian or Russian can be selected by the user. 1 Turn the power on to all devices used. 2 Press the MENU button to display the MA IN MENU. ø The “1.LANGUAGE/CLO CK SET” line appears highlighted.
SETTING THE LANGU A GE AND CLOCK Automatic Summer Time Adjustment 1 Follow steps 1 to 3 under “ Language S etting ” on page 11. <LANGUAGE/CLOCK@SET> *LANGUAGE-LANGUE-IDIOMA @-SPRACHE-LINGUA-.
SUPERIMPOSE DISPLA Y Selecting the Superimpose Display You can select to display or not the date, time, tape speed mode and number of alarm recordings. 1 Turn the power on to all devices used. 2 Press the MENU button to display the MA IN MENU. 3 Turn the JOG dial to select the “ 2.
VIDEO CASSETTE T APES Use only video cass ette tapes bearing the VHS logo. This VCR was primarily designed for use with E- 180 and E-240 cassette tapes. It is re commended that you use E-180 or E-240 standard grade VHS video cassette tapes for optimal performance.
VIDEO CASSETTE T APES Correct tape thread check function This function checks to make sur e that the cassette has been correctly loaded so that recording c an be carried out.
T APE MANA GEMENT This VCR is equipped with a tape management function. Using this function you can protect pr evious recordings and prevent overuse of the tape by contr olling the tape protection term (number of days), the maximum number of re-recordings of the tape and the recording group.
T APE MANA GEMENT Setting the Tape Management Function 1 Press the STANDBY/ON button. 2 Press the MENU button to display the MA IN MENU. 3 Turn the JOG dial to select the “ 6.TAPE MANAGEMENT ” line, then turn the SHUTTLE ring clockwis e. ø The (TAPE MANAGEMENT ) menu appears.
T APE MANA GEMENT Tape Management Conflict Display If a conflict that prevents record ing is found when the tape management function checks the tape data, the (TAPE MANAG EMENT) menu appears with the conflicting setting flashing and the VCR go into the st op mode.
NORMAL RECORDING Normal Recording Before starting œ Turn the power on to all devices used. œ Load a cassette tape with its erasure-prevention tab intact. NOTES: œ If “ TAPE IN MODE ” is set to “ REC ” in the (GENERA L SET) menu, recording will s tart.
NORMAL RECORDING Record Pause Recording can be interrupted temporarily. 1 Press the STILL /PAUS E button during recording. ø The pause/still indicator “ N ” flashes.
NORMAL RECORDING Clog Detection This VCR is equipped with a clog detection function. The recording quality is monitored automatically. W hen the heads are dirty and the recording quality deteriorates,.
NORMAL RECORDING Setting the Mode at the End of the Tape You can select the mode on the VCR when the tape reaches the end during recording. 1 Press the STANDBY/ON button. 2 Press the MENU button to display the MA IN MENU. 3 Turn the JOG dial to select the “ 3.
A UT OREPEA T RECORDING Autorepeat Recording The same tape can be recorded over many times . œ Follow the Before starting steps, under “ NORMAL RECORDING ” . 1 Press the MENU button to display the MA IN MENU. 2 Turn the JOG dial to select the “ 3.
ALARM RECORDING By connecting the ALARM IN terminal to a normally open door switch, an interphone, etc., a record ing can be done only when necessary. Alarm Recording Setting Alarm recording is performed when there is an input (trigger) at the ALARM IN terminal.
ALARM RECORDING Alarm Recording Reset Function To stop the recording of an alarm, close the connection between the ALARM RESET IN terminal and the COM terminal during alarm recording. Alarm Recording Counter Display œ During alarm recording, “ A” w ill be flashing on the digital display.
ALARM RECORDING Alarm Search To go to the beginning of a desired alarm recording. 1 Press the STANDBY/ON button. 2 Press the SEARCH button during stop mode. ø “ AL SEARCH 01 ” appears on screen. 3 Press the REC/PLAY SPEED l (or j ) button to set the desired alarm number (01 to 99), then turn the SHUTTLE ring clockwise (or counterclockwis e).
PR OGRAMME TIMER RECORDING There are three programme timer recording methods, daily recording, weekly rec ording or recording on certain days of the week. Exampl e 1: To record on ever y Saturday from 9:00 AM to 5:00 PM (17:00), in 24-hour mode (recording speed).
PROGRAMME TIMER RECORDING A timer recording of more than 24 hours can only be set on the 7th (SAT) and 8th (DAILY) lines of the (TIMER SET) menu. Exampl e 2: To record every week fr om Friday at 9:0 0 PM (2 1:00) to Monday at 7 :00 AM, i n 96-hour mode (recordi n g speed).
PROGRAMME TIMER RECORDING Setting the Holidays By setting the holidays, timer rec ording will be conducted on those days, as set for Sunday s. 1 Press the STANDBY/ON button. 2 Press the MENU button to display the MA IN MENU. 3 Turn the JOG dial to select the “ 8.
PROGRAMME TIMER RECORDING NOTES: œ During timer recording or timer recording stand-by, all the buttons on the VCR, except the TIMER button and the buttons to set/cancel the secur ity lock (see page 38), are disabled. œ If the power fails, the recording will be inter rupted.
RECORDING USING AN EXTERNAL TIMER INPUT Recording can be controlled by an exter nal start/stop signal input at the EXT T IMER IN terminal. While there is input at the EXT TI MER IN terminal, the external input indicator “E ” will light on the digital dis play and the input will be recorded.
SERIES RECORDING Using 2 VCRs or more, the series recording function lets you switch recording from one unit to the nex t (only with VCRs of the same model as this one). Series Recording Setup œ Connect 2 VCRs or more as illustr ated below. œ Follow the Before starting steps, under “ NORMAL RECORDING ” .
SINGLE IMA GE RECORDING The single image recording function of this VCR can be used to create image data files or animations. Single Image Recording Setup œ Follow the Before starting steps, under “ NORMAL RECORDING ” . 1 In stop mode, press the REC/PLAY SPEED l (or j ) button, to set the recording speed to “ 000 ” .
NORMAL PLA YB A CK Normal Playback 1 Turn on the power to the VCR and TV monitor. 2 Load the video cassette tape. 3 Press the REC/PLAY SPEED l (or j ) button to select the playback s peed mode. ø The selected playback speed mode is displayed on the digital display.
SPECIAL PLA YB A CK Picture Search (Forward and Reverse) 1 Turn the SHUTTLE ring clockwise (or counterclockwise), dur ing normal playback. See “ SHUTTLE Ring Operation ” . ø The image can be seen while the tape is advanced (or rewound) at high speed.
SPECIAL PLA YB A CK SHUTTLE Ring Operation From normal playback, still image, s top mode, etc., turn the clockwise or counterclock wise to select a mode as indicated below. 1 Turn the SHUTTLE ring in either dir ection where the desired mode is selected.
D A Y/TIME SEARCH Day/Time Search This searches for a s pecified day/time for still images to be played back. 1 Press the STANDBY/ON button. 2 Press the SEARCH button three times during stop mode. ø “ T/D SEARCH 01 00:00 ” will be displayed on screen.
SECURITY LOCK This VCR is equipped with two types of sec urity lock: a quick method security lock and a 4 digit security lock. The security lock function is des igned to prevent accidental stopping of recording if the STOP button is pressed inadvertently.
CLOCK ADJUSTMENT The time for the second and subsequent VCRs can be set to the same time as the first VCR. A signal from a separate device can also be us ed to set the time for the second and subsequent VCRs to the same time as the first VCR.
SETTING THE CASSETTE EJECT MODE Cassette Eject Setup When using two or more VCRs, the cassette tapes of all the VCRs or some of the VCRs can be ejected at the same time. NOTE: œ “ TERMINAL SET ” in the (OTHERS) menu should always be set to “ SET2 ” .
SYNCHR ONIZA TION CONTR OL When two or more VCRs are connected together, the VCRs can be operated simultaneously jus t by operating the VCR that has been set to “ MAST ER ” , without using a system controller (s old separately). There are two modes available: operator mode and administrator/installer mode.
SYNCHR ONIZA TION CONTROL Setting the Cassette Eject Mode Operator mode can be used to eject cassettes for all VCRs or for specified VCRs. 1 Follow steps 1 to 5 under “ Operator Mode ” . 2 Turn the JOG dial until the “ EJECT MODE ” setting is highlighted, then turn the SHUTTLE ri ng c lockwise.
SETTING FOR RS-485 OR RS-232C USE The RS-485 interface can be used to operate the VCR using a SANYO brand sy stem controller. Furthermore, the RS-232C interface can be used to operate the VCR using a computer. NOTES: œ This can only be used when the RS-485/232C interface board (VZU-485/232C) is installed.
CHECKING POWER F AILURE, F AILURE DUE TO CONDENSA TION AND USAGE DURA TION 1 Press the STANDBY/ON button. 2 Press the MENU button to display the MA IN MENU. 3 Turn the JOG dial to select the “ 9.OTHERS ” line, then turn the SHUTTLE ring clockwise.
OUTPUT TERMINALS TAPE END OUT Terminal œ During recording, when the end of the tape is reached or when the tape counter reading indicates 8 hours, the output becomes 0V (Low). During autorepeat recording, the output becomes 0 V ( Low) for about 2 seconds only.
OUTPUT TERMINALS SW OUT Terminal When recording, a pulse signal is output at the SW OUT terminal. This terminal is usually connected to the switc h input (SW IN) of devices lik e a camera switcher unit, or a quad compressor. SW OUT Term i nal Output Setting 1 Press the STANDBY/ON button.
OUTPUT TERMINALS WARNING OUT Terminal œ The WARNING OUT terminal output becomes 0 V (Low) in accordance with the (WA RNING OUT/CONTROL SET) menu. WARNING OUT Terminal Out put Sett ing 1 Press the STANDBY/ON button. 2 Press the MENU button to display the MA IN MENU.
OUTPUT TERMINALS REMOTE Jack Remote control of the VCR is possible by c onnecting a remote controller with a circuit such as indicated below, to the REMOTE jack. NOTES: œ Use a 3.5 mm mini-jack type plug. œ The connection should be done using a shielded cable no more than 5 meters long.
MAINTENANCE Daily Inspection The following daily inspections are recommended in order to assure long-term and trouble-free operation of the unit. The daily inspections are particularly important if us ing autorepeat recording. Inspection Procedure 1 Turn on the power to the VCR, camera, TV monitor and other connected devices.
MAINTENANCE Maintaining and Checking The Mechanism To maintain the VCR functions and features working properly, and to avoid damages or dirt on the tape, it is recommended to follow the maintenance points and periodicity indicated below. For detailed information, please contact your dealer.
TR OUBLESHOO TING GUIDE If the unit does not operate normally when you follow the instructions indic ated in the manual, please refer to the table below.
SPECIFICA TIONS General Specifications Video head system Dual-azimuth 4-head rotating helical scanning sys tem: Dual azimuth 2-head for record and standard playback Dual azimuth 4-head for forward pic.
SPECIFICA TIONS Other Specifications Operating temperature range 5 ° C to 40 ° C (41 ° F to 104 ° F) Operating humidity range 80% or less Power requirements ( SRT -8960P only ) 220-240V AC, 50Hz (or DC power: 12 to 24V DC) Power requirements ( SRT -8040P only ) 220-240V AC, 50Hz Power consumption 18 W Dimensions (W x H x D) 420 mm x 99.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Sanyo SRT-8040P c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Sanyo SRT-8040P - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Sanyo SRT-8040P, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Sanyo SRT-8040P va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Sanyo SRT-8040P, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Sanyo SRT-8040P.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Sanyo SRT-8040P. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Sanyo SRT-8040P ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
