Manuel d'utilisation / d'entretien du produit S83 du fabricant Samson
Aller à la page of 29
SAMSON ® S83 / S63 AMPLIFIER MIXER.
Introduction 1 S83/S63 F eatures 2 Guided T our - S83 4 Overview 4 Channel 5 Main Section 6 Rear Panel 8 Guided T our - S63 10 Overview 10 Channel 11 Main Section 12 Rear Panel 14 Connecting The S83/S.
Introduction Congratulations on purchasing the Samson S83/S63 Mixer Amplifier! In this manual, we’ll take you on a guided tour through all the features of this powerful and flexible device, and we’ll tell you how to get the most out of the S83/S63.
S83/S63 F eatures The Samson S83/S63 utilizes state-of-the-art technology in integrated mixer/amplifier design. Here are some of its main features: • Standard 19” rack-mount design (taking just four rack spaces) allows the S83 and S63 to be easily integrated into any setup.
S83/S63 F eatures • A phantom power switch enables you to use the S83 and S63 with high- quality condenser microphones. When turned on, 48 volts of phantom power is provided to the mic connectors of all input channels. • Protection relay circuitry prevents “thumps” when powering on or off.
Guided T our - S83 Over view The following illustration shows an overview of the front panel of the S83: 4 -12 +12 2.5K 0 -15 +15 HIGH 0 -12 +12 500Hz 0 -15 +15 LOW 0 +15 LEVEL 0 +10 EFF1 MON 0 +4 -40.
Guided T our - S83 Channel 1: Level (white) - This knob determines the final signal level being sent by a channel to the main speaker outputs as well as to Effect send 1 (see #2 below). In practice, this will be used to adjust the levels of the various signals being blended together by the S83.
Guided T our - S83 Main Section 1: Meter - This seven-segment bar meter shows the continuous output level of the S83. For optimum signal-to-noise ratio, try to adjust all levels (channel and main) so that program material is usually at or around 0 VU, with occasional but not steady excursions to the +2 segment.
Guided T our - S83 Main Section output signal. At the fully clockwise ( “ +10 ” ) position, approximately 10 db of gain is being added by the mixer to the output signal. For more information, see the “ Setting Up and Using the S83/S63 ” section in this manual.
Guided T our - S83 Rear P anel 1: Power switch - As you may have guessed, this is what you use to turn the S83 on and off. The built-in protection relay circuitry (which mutes the outputs for approximately five seconds after powering on) prevents power-on “ thumping, ” which can potentially damage connected speakers.
Guided T our - S83 Rear P anel 5: Amp In - This unbalanced input allows you to connect any external mono- phonic line-level signal directly to the S83 power amplifier. This input is not affected by either the ten-band graphic master equalizer or the S83 ’ s Main Level control.
Guided T our - S63 Over view The following illustration shows an overview of the front panel of the S63: 10 Main Section Channels -12 +12 1 kHz 0 -15 +15 HIGH 0 -15 +15 LOW 0 +15 LEVEL 0 +10 EFF1 MON .
1: Level (white) - This knob determines the final signal level being sent by a channel to the main speaker outputs as well as to Effect send 1 (see #2 below). In practice, this will be used to adjust the levels of the various signals being blended together by the S63.
1: Return 1-2 Level (green) - This knob determines the input level of signal arriving via Effects returns 1 and 2 (mixed together in mono). This signal is at unity gain (no boost or attenuation) when the knob set to the 0 position and is boosted when the knob is turned to the right of 0 and attenuated when turned to the left of 0.
4: Ten-Band Graphic Master EQ - These sliders allow you to add ±15 db of boost or attenuation to ten different frequency areas, affecting the main output signal of the S63. When a slider is at its center detented ( “ 0 db ” ) position, the selected frequency area is unaffected (it is said to be flat ).
1: Power switch - As you may have guessed, this is what you use to turn the S63 on and off. The built-in protection relay circuitry (which mutes the outputs for approximately five seconds after powering on) prevents power-on “ thumping, ” which can potentially damage connected speakers.
Guided T our - S63 Rear P anel 5: Amp In - This unbalanced input allows you to connect any external mono- phonic line-level signal directly to the S63 power amplifier. This input is not affected by either the ten-band graphic master equalizer or the S63 ’ s Main Level control.
16 The actual connections you ’ ll make to and from the S83/S63 will vary according to the environment you use it in and the particular equipment you have.
17 Setting up your S83/S63 is a simple procedure which takes only a few minutes: 1. Remove all packing materials (save them in case of need for future service) and decide where the unit is to be physically placed — it can be mounted in any standard 19 ” rack, requiring four rack spaces.
18 You ’ re now ready to establish the correct gain structure — the key to getting the best performance from the S83/S63, or from any mixer, for that matter.
19 i. Repeat step (g) above for each instrument connected to the S83/S63 channel line inputs. j. The procedure for setting optimum microphone levels is virtually identical; sing or speak into the mic at the level you expect to use in performance while slowly raising the level control for that channel to its “ 0 ” position.
20 Suggested P erformance Application - S83 The following illustration shows the basic interconnections between an S83 and external equipment when used in a typi- cal live performance application: The.
21 Suggested P erformance Application - S63 The following illustration shows the basic interconnections between an S63 and external equipment when used in a typi- cal live performance application: The.
22 Grounding T echniques Hum and buzz are the biggest enemies you face when interconnecting a large number of different pieces of equipment to a central audio mixer.
23 Using Equalization One of the most exciting aspects to using a mixer such as the S83 or S63 is hav- ing the ability to shape a sound, using a process called equalization . But there are few areas of sound engineering more misunderstood than equalization, and, just as good EQ can really help a sound, bad EQ can really hurt it, so read on.
24 Using Equalization until the ringing or feedback disappears. Don ’ t lower the frequency area any further than you need to, or the quality of the overall sound may suffer.
25 Using The Effects Sends and Retur ns The two Effects sends provided by the S83 and S63 allow you to combine the signal from multiple channels and send the resulting mix to the rear panel Monitor output jack, to the internal reverb unit, or to external devices such as effects processors.
26 Using the Monitor Output and Inter nal Re verb Using the Monitor Output In live performance, it is usually desirable to have onstage monitor speakers that allow the performer to clearly hear the music being played. Often, however, the performer requires a different mix than that being sent to the house speakers.
27 Specifications Mixer / Pre Amp Section: Total Harmonic Distortion (with 30 kHz LPF, trim center) S83 0.045% S63 0.01% Signal To Noise Ratio (both models, with 30 kHz LPF, trim center) 78 dB Maximum.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Samson S83 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Samson S83 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Samson S83, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Samson S83 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Samson S83, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Samson S83.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Samson S83. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Samson S83 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
