Manuel d'utilisation / d'entretien du produit TS1344L du fabricant Ryobi
Aller à la page of 30
SA VE THIS MANUAL FOR FUTURE REFERENCE OPERA TOR’S MANUAL 10 in. Compound Miter Saw TS1344L - Double Insulated Y our miter saw has been engineered and manufactur ed to our high standard for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-free performance.
2 Introduction ..................................................................................................................................................................... 2 W arranty ..................................................
3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below , may r esult in electric shock, fire, and/or serious personal injury . READ ALL INSTRUCTIONS KNOW YOUR POWER TOOL. Read the operat or’ s manual carefully .
4 GENERAL SAFETY RULES INSPECT TOOL CORDS PERIODICALL Y . I f damaged, have repair ed by a qualified service technician at an authorized service facility . Repair or replace a damaged or worn cord immediately . Stay constantly aware of cor d location and keep it well away from the r otating blade.
5 SPECIFIC SAFETY RULES NEVER reach behind, under , or within three inches of the blade and its cutting path with hands and fingers for any reason. NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the cutting path of the blade.
6 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer .
7 EXTENSION CORDS When using a power tool at a considerable distance from a power source, be sur e to use an extension cord that has the capacity to handle the current the tool will draw . An undersized cord will cause a dr op in line voltage, resulting in overheating and loss of power .
8 GLOSSAR Y OF TERMS Non-Through Cuts (table saws and compound sliding miter saws) Any cutting operation where the blade does not extend completely through the thickness of the workpiece. Push Blocks (jointer planers) Device used to feed the workpiece over the jointer planer cutterhead during any operation.
9 FEA TURES PRODUCT SPECIFICA TIONS Blade Arbor ............................................................. 5/8 in. Blade Diameter .......................................................... 10 in. No Load Speed ................................... 5,500 r/min.
10 FEA TURES KNOW YOUR COMPOUND MITER SA W See Figure 1. The safe use of this product r equires an understanding of the information on the tool and in this operator’ s manual as well as a knowledge of the project you ar e attempting. Before use of this product, familiarize yourself with all operating features and safety rules.
11 FEA TURES MITER LOCK HANDLE See Figure 2. The miter lock handle securely locks the saw at desir ed miter angles. POSITIVE STOPS ON MITER T ABLE Positive stops have been provided at 0°, 15°, 22-1/2°, 31.6°, and 45 ° . The stops have been pr ovided on both the left and right side of the miter table.
12 LOOSE P ARTS WARNING: The use of attachments or accessories not listed might be hazardous and could cause serious personal injury . The following items are included with the tool: Miter Lock Handle Dust Bag W ork Clamp Blade Wr ench AAA Batteries Operator’ s Manual Fig.
13 ASSEMBL Y Fig. 7 MOUNTING SURF ACE BASE TRACE HOLES A T THESE LOCA TIONS FOR HOLE P A TTERN TRACE HOLES A T THESE LOCA TIONS FOR HOLE P A TTERN WARNING: Do not connect to power supply until assembly is complete. Failure to comply could r esult in accidental start- ing and possible serious personal injury .
14 ASSEMBL Y Fig. 8 Fig. 10 TO LOOSEN MITER LOCK HANDLE TO TIGHTEN DUST BAG EXHAUST PORT BASE WORK CLAMP MITER LOCK HANDLE See Figure 8. T o install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threaded hole in the control arm.
15 INST ALLING BA TTERIES FOR LASER See Figure 11. Remove screw fr om battery compartment cover using the Phillips end of the supplied blade wrench. Remove cover and set aside. Install two AAA batteries according to polarity indicators inside the battery compartment.
16 ASSEMBL Y TO INST ALL / REPLACE THE BLADE See Figures 13 - 14. WARNING: A 10 in. blade is the maximum blade capacity of the saw . Never use a blade that is too thick to allow laser guide washer to engage with the flats on the spindle.
17 ASSEMBL Y WARNING: M ake sure the spindle lock button is not engaged before r econnecting saw into power source. Never engage spindle lock button when blade is rotating. NOTE: Many of the illustrations in this manual show only portions of the compound miter saw .
18 ASSEMBL Y Fig. 17 Fig. 18 VIEW OF BLADE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED VIEW OF BLADE NOT SQUARE WITH FENCE, ADJUSTMENTS ARE REQUIRED MITER LOCK HANDLE MITER T ABLE BLADE FRAMING SQUARE MITER FENCE MITER LOCK HANDLE MITER T ABLE BLADE FRAMING SQUARE MITER FENCE Fig.
19 ASSEMBL Y SQUARING THE BLADE TO THE MITER T ABLE See Figures 19 - 22. Unplug the saw . Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position. Loosen the miter lock handle appr oximately one-half turn.
20 OPERA TION WARNING: Do not allow familiarity with tools to make you care- less. Remember that a careless fraction of a second is sufficient to inflict serious injury . WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.
21 OPERA TION Rotate the control arm until the pointer aligns with the desired angle on the miter scale. Tighten the miter lock handle securely . Place the workpiece flat on the miter table with one edge securely against the fence. If the boar d is warped, place the convex side against the fence.
22 OPERA TION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 27. Before turning on the saw , perform a dry run of the cutting operation just to make sure that no pr oblems will occur when the cut is made.
23 OPERA TION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. Before turning on the saw , perform a dry run of the cutting operation just to make sure that no pr oblems will occur when the cut is made.
24 OPERA TION 4 PITCH OF SIDE NUMBER OF SIDES 0° 6 M- 45.00° B- 0.00° 5° 10° 15° 20° 25° 30° 35° 40° 45° 50° 55° 60° 65° 70° 75° 80° 85° 90° 5 7 8 9 10 M- 36.00° B- 0.00° M- 30.00° B- 0.00° M- 25.71° B- 0.00° M- 22.50° B- 0.
25 OPERA TION When setting the bevel and miter angles for compound miters, remember that the settings ar e interdependent; changing one angle changes the other angle as well. Keep in mind that the angles for crown moldings ar e very precise and dif ficult to set.
26 OPERA TION WARNING: T o avoid a kickback and to avoid serious personal injury , never position the concave edge of bowed or warped material against the fence. CLAMPING WIDE WORKPIECES See Figure 32. When cutting wide workpieces, such as 2 in. x 6 in.
27 ADJUSTMENTS WARNING: Before performing any adjustment, make sur e the tool is unplugged from the power supply . Failure to heed this warning could result in serious personal injury . The compound miter saw has been adjusted at the factory for making very accurate cuts.
28 ADJUSTMENTS DANGER: Laser radiation. Av oid direct eye contact with light sour ce. WARNING: Use of controls or adjustments or performance of pr o- cedures other than those specified her ein can result in hazardous radiation exposur e. TO ADJUST THE LASER GUIDE See Figure 34.
29 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts can create a hazar d or cause product damage. WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1 during product operation.
• SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center . Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Authorized Service Center .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Ryobi TS1344L c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Ryobi TS1344L - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Ryobi TS1344L, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Ryobi TS1344L va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Ryobi TS1344L, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Ryobi TS1344L.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Ryobi TS1344L. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Ryobi TS1344L ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
