Manuel d'utilisation / d'entretien du produit R10632 du fabricant Ryobi
Aller à la page of 20
THANK YOU FOR BUYING A RYOBI CORDLESS CIRCULAR SAW. Your new cordless circular saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
Page 2 Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved. The following recommended accessories are current and were available at the time this manual was printed. ■ 5-1/2 in. (140 mm) Thin Kerf Blade ■ Table of Contents .
Page 3 W ARNING: Do not attempt to operate this tool until you have read thoroughly and understand completely all instructions, safety rules, etc. contained in this manual. Failure to comply can result in accidents involving fire, electric shock, or serious personal injury.
Page 4 IMPORTANT SAFETY RULES FOR BATTERY TOOLS ■ Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in an operating condition. Be aware of possible hazards when carrying your battery tool, when making adjustments to it, or when changing accessories.
Page 5 RULES FOR SAFE OPERATION (Continued) IMPORTANT SAFETY INSTRUCTIONS FOR CIRCULAR SAWS ■ KEEP GUARDS IN PLACE AND IN WORKING ORDER. Never wedge or tie lower blade guard open. Check operation of lower blade guard before each use. Do not use if lower blade guard does not close briskly over saw blade.
Page 6 SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a characteristic of current --- Direct Current Type or a characteristic of current n 0 No Load Speed Rotational speed, at no load .
Page 7 KNOW YOUR CORDLESS CIRCULAR SAW See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. Features include easily operated bevel cut and depth of cut adjustment mechanisms; positive 0 ° bevel stop; spindle lock; and blade wrench storage.
Page 8 LED FUNCTION OF CHARGER 1423701 See Figure 3. LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: ■ Red LED lighted = Fast Charging Mode ■ Green LED lighted = Fully Charged Battery Pack ■ Yellow and Green LED Lighted = Control Charge or Defective Battery Pack.
Page 9 W ARNING: Always remove battery pack from your saw when you are assembling parts, making adjustments, assembling or removing blades, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury .
Page 10 45 45 50 50 30 30 22 22 1 1 2 3 0 45 Fig. 6 BLADE SCREW BLADE WRENCH SPINDLE LOCK BUTTON ■ Fit saw blade inside lower blade guard and onto spindle. NOTE: The saw teeth point upward at the front of saw as shown in figure 5. ■ Replace outer blade washer .
Page 11 KICKBACK See Figure 8. The best guard against kickback is to avoid dangerous practices. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood.
Page 12 ■ When making a cut use steady, even pressure. Never force cuts. ■ Do not cut warped or wet lumber. ■ Always hold your saw firmly with both hands and keep your body in a balanced position so as to resist the forces of kickback should it occur.
Page 13 TO HELP MAINTAIN CONTROL: ■ Always support your workpiece near the cut. ■ Support your workpiece so the cut will be on your left. ■ Clamp your workpiece so it will not move during the cut. Place your workpiece with its good side down. NOTE: The good side is the side on which appearance is important.
Page 14 TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base as shown in figure 17. Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut.
Page 15 TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between zero and 50 ° . NOTE: When making cuts at 50 ° , blade should be set at full depth of cut. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut.
Page 16 1 2 45 0 0 15 22 30 45 50 45 4 5 50 5 0 30 30 22 22 POSITIVE 0 ° BEVEL STOP See Figure 21. Your saw has a positive 0 ° bevel stop, that has been factory adjusted to assure 0 ° angle of your saw blade when making 90 ° cuts. However, misalignment can occur during shipping.
Page 17 45 45 50 50 30 30 22 22 TO RIP CUT OPTIONAL RIP GUIDE (EDGE GUIDE) See Figure 23. Use a guide when making long or wide rip cuts with your saw. An optional rip guide with a five inch scale is available or you can make an efficient rip guide by clamping a straight edge to your workpiece.
Page 18 W ARNING: When servicing, use only identical replacement parts. Use of any other part may create a hazard or cause product damage. W ARNING: Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc. come in contact with plastic parts.
Page 19 NOTES.
983000-055 R YOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29622 Post Office Box 1207 Anderson, SC 29622-1207 Phone 1-800-525-2579 www .ryobitools.com • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Ryobi R10632 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Ryobi R10632 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Ryobi R10632, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Ryobi R10632 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Ryobi R10632, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Ryobi R10632.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Ryobi R10632. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Ryobi R10632 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
