Manuel d'utilisation / d'entretien du produit 767rj du fabricant Ryobi
Aller à la page of 22
767rj 2-Cycle Gas T rimmer OPERA TOR’S MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or 1-800-265-6778 in CANADA www.ryobi.com IMPORT ANT MANUAL DO NOT THROW AW A Y.
INTRODUCTION T ABLE OF CONTENTS 2 THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator’s manual provides you with easy-to-under- stand operating instructions.
CALIFORNIA EMISSION REGULA TIONS 3 SP ARK ARRESTOR W ARNING! RULES FOR SAFE OPERA TION NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington.
RULES FOR SAFE OPERA TION 4 READ ALL INSTRUCTIONS BEFORE OPERA TING • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.
RULES FOR SAFE OPERA TION 5 • Do not touch the engine or muffler. These parts get extremely hot from operation. When turned off they remain hot for a short time. • Do not operate the engine faster than the speed needed to cut, trim or edge. Do not run the engine at high speed when not cutting.
SYMBOL MEANING • PRIMER BULB Push primer bulb, fully and slowly , 5 to 7 times. • UNLEADED FUEL Always use clean, fresh unleaded fuel. • THROWN OBJECTS AND ROT A TING CUTTER CAN CAUSE SEVERE INJUR Y WARNING: Do not operate without the cutting attachment shield in place.
RULES FOR SAFE OPERA TION 7 KNOW YOUR UNIT APPLICA TIONS • Cutting grass and light weeds. • Decorative trimming around trees, fences, etc. Handle Hardware Primer Bulb Air filter/Muffler Cover Fuel.
6. While holding the unit in the operating position (Fig. 3), position the J-handle to the location that provides you the best grip. 7. Tighten the clamp screws evenly, until the J-handle is secure. INST ALLING THE CUTTING A TT ACHMENT SHIELD Use the following instructions if the cutting attachment shield on your unit is not installed.
ASSEMBL Y INSTRUCTIONS 9 OIL AND FUEL INFORMA TION WARNING: Gasoline is extr emely flammable. Ignited V apors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the ar ea.
ST ARTING/STOPPING INSTRUCTIONS 10 4. Place the choke lever in the FULL choke position ( A ) (Fig. 8). 8. If the engine does not start, repeat steps 4 through 7. NOTE: If the engine floods while trying to start, place the choke lever in the RUN position ( C ) (Fig.
11 OPERA TING INSTRUCTIONS Fig. 10 Fig. 11 Each time the head is bumped, about 1 inch (25.4 mm.) of trimming line is released. A blade in the cutting attachment shield will cut the line to the proper length if excess line is released. For best results, tap the Bump Head ™ on bare ground or hard soil.
WARNING: Always use the corr ect line length when installing trimming line on the unit. The line may not release pr operly if the line is too long. 2. Hold the outer spool and turn the inner reel counterclockwise to line up the arrows on the outer spool and inner reel (Fig.
MAINTENANCE AND REP AIR INSTRUCTIONS 13 Line Locking Hole Trimming Line Line Loading Hole Eyelet 5. Insert the line into the locking hole (Fig. 15). Do not push the line more than 1/2 inch (12.7 mm.) into the line locking hole. When inserted correctly the line will form a small loop (Fig.
MAINTENANCE AND REP AIR INSTRUCTIONS 14 2. Pull out the bump knob, spring, and foam seal (Fig. 19, Pg. 13). 3. Pull the inner reel with existing line from the outer spool (Fig. 19, Pg. 13). 4. Remove any existing line from the inner reel before cleaning.
MAINTENANCE AND REP AIR INSTRUCTIONS 15 Fig. 25 Fig. 26 Fig. 27 4. Apply enough clean SAE 30 oil to lightly coat the filter (Fig. 27). Air Filter 3. Wash the filter in detergent and water (Fig. 26). Rinse the filter thoroughly. Squeeze out excess water.
MAINTENANCE AND REP AIR INSTRUCTIONS 16 0.020 in. (0.5 mm.) Fig. 30 CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable through the Air filter/Muffler cover (Fig. 29). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments.
CLEANING AND STORAGE 17 TRANSPORTING • Allow the engine to cool before transporting. • Secure the unit while transporting. • Drain fuel from unit. • Tighten fuel cap before transporting. CLEANING WARNING: T o avoid serious personal injury , always turn your trimmer off and allow it to cool before you clean or do any maintenance on it.
TROUBLESHOOTING 18 CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Replace the inn.
SPECIFICA TIONS 19 Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES 20.
21 The California Air Resources Board and Ryobi Outdoor Products (ROP), are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the State's stringent anti-smog standards.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE TWO (2) YEAR WARRANTY PERIOD OR NINETY (90) DAYS FOR PRODUCTS USED FOR ANY COMMERCIAL PURPOSE. ACCORDINGLY, ANY SUCH IMPLIED WARRANTIES INCLUDING .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Ryobi 767rj c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Ryobi 767rj - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Ryobi 767rj, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Ryobi 767rj va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Ryobi 767rj, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Ryobi 767rj.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Ryobi 767rj. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Ryobi 767rj ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
