Manuel d'utilisation / d'entretien du produit SR-60 du fabricant RIDGID
Aller à la page of 51
WARNING! Read this operator’s manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire and/or serious personal injury.
ii www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Table of Contents GENERAL SAFETY INFORMATION ..................................................................................................... ...... 2 SR-60 C OMPONENTS .
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 1 SeekTech SR-60 SeekTech ® SR-60 Record the Serial Number of your unit below and retain for your records.
2 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 General Safety Information WARNING Read and understand all instructions.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 3 SeekTech SR-60 SR-60 Use and Care • Use equipment only as directed . Do not operate the SR-6 0 unless you have read the operator’s manu al. • Do not immerse the antennas in water.
4 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 DANGER Important Notice The SR-60 is a diagnosti c tool that senses electromagnetic fields emitted by objects underground. It is meant to aide the user in locating these objects by recognizi ng chara cteristics of the field lines and displaying them on the screen.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 5 SeekTech SR-60 SR-60 Component s Figure 1: SR-60 Components.
6 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Introduction to the SR-60 Getting S t arted Installing/Changing Batteries To install batteries into the SR-60, turn the unit over to access the battery compartment. Turn the knob on the battery cover counter cl ockwi se.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 7 SeekTech SR-60 Common Display Elements Figure 4: Common Display Elements The display screen in A ctive Line Trace, Passive Line Trac.
8 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 • Guidance Line Shows the alignment of the target line and helps determine when the locator is directly over the target line. It will be longest when di rectly aligned with the target line.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 9 SeekTech SR-60 the Main Menu, they will not appear when using the Frequency Key to cycle through freque ncie s. Frequencies whi ch appear in the Main Menu and are checked for activation are called “Che cked-Active”.
10 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 • Frequency / Left Key – Used to set the In-Use Frequency of the SR-60 from the set of Checked-Active frequ encies. Each short press cycles to the next Checke d-Active frequency.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 11 SeekTech SR-60 Set up Once the SR-60 is up and running, the next step is to set up the frequencies need ed to match the transmitter frequency bein g used, or the frequency of the line to be located.
12 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Figure 15: Highlighti n g a D e sired Freque ncy ( 8 kHz ) 3. Press the Select Key ( s h o w n b e l o w ) t o check the box for each frequen cy to be use d.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 13 SeekTech SR-60 locator receiver is g etting closer or further away from the Sonde. If desired, force the sound to re-center at a medium level (in any mode) by pre ssing the Select Key during operation.
14 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 meter, or other point. Im portant: The connectio n between the transmitter an d the conductor must b e a clean, firm connection. The transmi tter is also connected to a ground sta ke providing a strong open path to ground.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 15 SeekTech SR-60 Figure 22: Traci ng Line Showi ng High Distor tion 3. Use the Guidance Arrows, Proximity Number, Signal Strength, and Tracing Line to guide the line trace.
16 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Measuring Depth (Line Tracing Modes) The SR-60 calculates Measured Depth by comparing the strength of the signal at the lower antenna to that at the upper antenna.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 17 SeekTech SR-60 Current and Signal Angle Reading The Current Strength ( ) and Signal Angle indicator ( ) in the upper right co rner .
18 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 overcome resistance and inject more current onto the line. e. Re-l ocate the ground conne ction for a better circuit. Ensure the re is enough contact (ground stake is sufficiently deep) especially in dryer soils.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 19 SeekTech SR-60 Figure 28: Screen Displ ay in Di fferent Locations (Line Tracing).
20 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Passive Line T racing In passive mode, the SR-60 is looking for electromagnetic “noise ” t hat has found its way onto a buried utility line by any available means.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 21 SeekTech SR-60 In general, directly conne cted Active Line Tracing i s more reliable than Passive Line Tracing.
22 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Operating Tips for Passive Line Tracing 1. In Passive Locating if you are looking for a known line, be sure you are using the best frequency for the line in que stion.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 23 SeekTech SR-60 Figure 34: Dipole Field When locating a Sonde, first set up the locate: • Activate the Sonde before putting it in the line. Select the same Sonde frequency on the SR-60 and make sure it is receiving the signal.
24 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 • Mark the first Pole location found with a red triangular Pole marker.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 25 SeekTech SR-60 that the signal falls away on every side of the maximum signal location. Note : If following a mo ving Sonde, it may be easiest to “chase” a pole, and then to pinpoint the actual position of the Sonde only after the Sond e has stopped moving.
26 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Figure 39: Screen Display in Different Locati ons (Sonde).
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 27 SeekTech SR-60 Figure 40: Tilted Sonde, Poles, and E qu ator Note the right-hand Pole is closer to the Equator, due to tilt.
28 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Custom User Frequencies SR-60 users can set and use custom frequen cies.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 29 SeekTech SR-60 Figure 45: Editing a User-Defined Frequency (Note: Trash Ic on for deleting Frequency appears when Frequency is set to 0). 3. Use the arrow keys to move throu gh the digits and increase or decrease them.
30 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 11. Display Elements Co ntrol (Sub- menus will display when selected for Sonde or line tracing modes.) 12. Frequency Selection Control (Sub-menus will display for categories of frequencies that can b e selected.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 31 SeekTech SR-60 Figure 49: Setting Backlight Mode (On/Off/Auto) LCD Contrast When this is selected by pressing the Select Key, the contrast can be adjusted ( Figure 50). Use the Up an d Down Keys to make the screen lighter or d arker ( Figure 51).
32 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 traveling along the Race Track ( Figure 54). The Watermark is a graphi c representation of the hig hest Signal Strength reached (in Sonde mode) or the highest Proximity Signal level reached (i n Line Tracing modes).
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 33 SeekTech SR-60 Figure 57: Signal Focus Control Note this means that when usin g a more narrow Signal Focus Control setting, it is nece ssary to move the receiver along the line more slo wly.
34 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Figure 60: Setting a Frequency to “Currently Availab le” Status To switch to a “Currently Av ailable” frequ.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 35 SeekTech SR-60 Menu T ree The following figure shows options an d controls built into the SR-60 menus.
36 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Informational Locating The normal shape of a field around a long conductor such as a pipe or cable is circular (cylindrical in three dimensions).
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 37 SeekTech SR-60 underground lines (ele ctrical conductors like m etal cables and pipes) o r Sondes (actively transmitting beacons). When the fields are simple and undistorted, then the informat ion from sensed fields is representative of the buried object.
38 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 be able to make the correct decision rapidly and accurately. A Better W ay of Locating The SR-60 gives the operator.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 39 SeekTech SR-60 Orientation to the Signal Because of the multipl e signals being pro cessed by each Omnidirectional antenna, the target’s signal always gets stronge r as t he receiver gets closer to the target.
40 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 line. If further assistance is needed, please call RIDGE Tool Technical Service at 800-519-3456. If appropriate: replacements can be o rdered from your Ridgid dealer.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 41 SeekTech SR-60 Icons and Symbols Figure 72: Icons and Symbols.
42 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Glossary -- Definitions Active Line Tracing A mode of locating using a Line Transmitter to inje ct a chosen frequen.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 43 SeekTech SR-60 Glossary -- Definitions Distortion The impact of near-by fields, other conducto rs , magnetic flux, or other interference on a circular electro-magnetic field.
44 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Glossary -- Definitions Operating Screen The display screen of the instrument as seen when locating. It include s an Active View area, where the Tracing Line appears in Line Trace modes, and where P ole and Equator icons appear in Sonde mode.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 45 SeekTech SR-60 T rouble Shooting Guide PROBLEM PROBABLE FAULT LOCATION SR-60 locks up during use. Power the unit off, and then back on. Remove the batteries if the unit will not switch off.
46 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 S pecifications • Weight w/ batteries ....... 5.4 lbs. (2.5 kg) • Weight w/o batteries ..... 4.7 lbs. (2.1 kg) Dimensions • Length ........................... 14” (35.
Ridge Tool Compan y Elyria, Ohio U.S.A www .seektech .com 47 SeekTech SR-60 Manufacturers Frequency T able Displayed Option Company Available Frequencies Model Exact frequency (Hz) Notes Dy na 3M Dynatel ™ 577Hz 8kHz 33kHz 200kHz 2273 577 8192 32768 200012 200 KHz not present in European model of the ST-510.
48 www .seektech. com Ridge Tool Company Elyria, Ohio U.S . A SeekTech SR-60 Displayed Option Company Available Frequencies Model Exact frequency (Hz) Notes RIDGID (Old) Ridge Tool Co. 512Hz 8kHz 33kHz 51kHz 200kHz 512 8192 32768 51712 200000 200k changed to 93khz in European model of the ST- 510.
Ridge Tool Company 400 Clark Street Elyria, Ohio 44 036-2023 Part Number : 748-028-601-0A Rev. A What is covered RIDGID® tools are warranted to be free of defects in workmanship and ma terial. How long coverage lasts This warranty lasts for the lifetime of the RIDGID® t ool.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté RIDGID SR-60 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du RIDGID SR-60 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation RIDGID SR-60, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le RIDGID SR-60 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le RIDGID SR-60, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du RIDGID SR-60.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le RIDGID SR-60. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei RIDGID SR-60 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
