Manuel d'utilisation / d'entretien du produit R3200 du fabricant RIDGID
Aller à la page of 22
1 ® OPERA T OR’S MANUAL 7-1/4 in. (184 mm) Circular Saw R3200 Double Insulated This new circular saw has been engineered and manufactured to our high standard for dependability , ease of operation and operator safety . When properly cared for , the saw will give you years of rugged, trouble-free performance.
2 ■ Introduction ...................................................................................................................................................................... 2 ■ General Safety Rules ......................................
3 W ARNING: Read and understand all instructions. Failure to follow all instructions listed below , may result in elec- tric shock, fire and/or serious personal injury . SA VE THESE INSTRUCTIONS W ork Area ■ Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
4 Service ■ T ool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury . GENERAL SAFETY RULES ■ When servicing a tool, use only identical replace- ment parts.
5 SPECIFIC SAFETY RULES ■ Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. ■ Blade depth and bevel adjusting locking levers must be tight and secure before making cut.
6 SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the ool better and safer .
7 SPECIFICA TIONS DOUBLE INSULA TION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation.
8 FEA TURES Before using the saw , familiarize yourself with all operating features and safety requirements. However , do not let famil- iarity with the tool make you careless. W ARNING: Exercise caution when using the circular saw . Care- less actions, for even a fraction of a second, can result in serious personal injury .
9 Fig. 1 FEA TURES POWER CORD RIP GUIDE HANDLE FULL LENGTH KERF INDICATOR DUST CHUTE SPINDLE LOCK SWITCH FRONT HANDLE LIGHTED PLUG.
10 ASSEMBL Y Fig. 2 SPINDLE BLADE SCREW OUTER FLANGE WASHER (“D” WASHER) BLADE INNER FLANGE BUSHING WARNING: The tool should never be connected to a power supply when you are assembling parts, making ad- justments, cleaning, performing maintenance, or when the tool is not in use.
11 ASSEMBL Y REMOVING BLADE See Figure 3. Follow these directions to remove the blade. ■ Unplug the saw. CAUTION: To prevent damage to the spindle or spindle lock, always allow motor to come to a complete stop before engaging spindle lock. ■ Depress spindle lock button.
12 OPERA TION SAW BLADES The best of saw blades will not cut efficiently if they are not kept clean, sharp, and properly set. Using a dull blade will place a heavy load on the saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available.
13 OPERA TION KICKBACK See Figure 5, 6, 7, and 8. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood. DANGER: Release switch immediately if blade binds or saw stalls.
14 OPERA TION WARNING: The tool should never be connected to a power supply when you are assembling parts, making ad- justments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury.
15 OPERATING THE SAW See Figures 11, 12, and 13. It is important to understand the correct method for operating the saw. Refer to the figures in this section to learn the correct and incorrect ways for handling the saw. WARNING: To make sawing easier and safer, always maintain proper control of the saw.
16 OPERA TION CROSS CUTTING/RIP CUTTING See Figure 14. When making a cross cut or rip cut, align the line of cut with the full length kerf indicator on the base as shown in the figure.
17 BEVEL CUTTING See Figures 17 and 18. To make the best possible cut, follow these helpful hints. ■ Align the line of cut with the inner blade guide notch on the base when making 45 ° bevel cuts. ■ Make a trial cut in scrap material along a guideline to determine how much you should offset the guideline on the cutting material.
18 POCKET CUTTING See Figure 19. WARNING: Always adjust bevel setting to zero before making a pocket cut. Attempting a pocket cut at any other setting can result in loss of control of the saw possi- bly causing serious injury. Follow these directions to pocket cut.
19 0 15 22 1 /2 1 /2 30 45 51 WARNING: The tool should never be connected to a power supply when you are assembling parts, making ad- justments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury.
20 MAINTENANCE W ARNING: When servicing use only identical RIDGID® replace- ment parts. Use of any other parts may create a hazard or cause product damage. W ARNING: The saw should never be connected to a power sup- ply when you are assembling parts, making adjust- ments, cleaning, performing maintenance, or when the tool is not in use.
21 This product is manufactured under license from Ridgid, Inc. by One World Technologies, Inc. All warranty communications should be directed to One World Technologies, Inc.
22 ® Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté RIDGID R3200 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du RIDGID R3200 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation RIDGID R3200, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le RIDGID R3200 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le RIDGID R3200, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du RIDGID R3200.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le RIDGID R3200. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei RIDGID R3200 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
