Manuel d'utilisation / d'entretien du produit 400SX du fabricant Profile
Aller à la page of 19
MOSFET POWER AMPLIFIERS Installation Instructions / Owner's Ma nual 100SX 200SX 400SX 440SX 600SX 640SX 800SX 1200SX.
I NTRODUCTION Congratulations on your purchase of a California state-of-the-art power amplifier. Your selection of a California car audio product indicates a true appreciation of fine musical reproduction.
S AFETY PRECAUTIONS Fuse amplifier's power wire at the battery . Be sure to fuse the power wire within 12" of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery.
F EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current.
Bass Boost For added low frequency performance all amplifiers are equipped with 12 dB bass boost. Power Fusing This protects the amplifier against short circuits and excessive current. Remote Turn-on Automatically turns amplifier on when connected to the head unit's remote output.
M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation.
REM GND B+ Fuse Bridged Speaker Output R L Connect the amplifier to the car's battery. At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box. We recommend using an 4 to 6 gauge power wire for your connections depending on the amplifier and length of the wire.
Filter Low Off Hi Bass Boost 0 12 X-over 40 130 85 Level Min Max Input CH1 CH2 CH3 CH4 Min Filter Low Off Hi Bass Boost 0 12 X-over 40 130 85 Level Min Max Input CH1 CH2 CH3 CH4 Min Input Level Min Ma.
Left Right Filter Low Off Hi PROTECTION POWER Input Level Min Max X-over 40 130 85 Bass Boost 0 12 Hi-Level Input L- R- L+ R+ If a low level RCA signal source is not available, you may still wire the models 100SX, 200SX, and 400SX with high-level or speaker level outputs from your head unit.
CH1 CH2 CH3 CH4 Fuse CH3 CH4 Bridged CH1 CH2 Bridged Speaker Output REM GND B+ REM GND B+ Fuse Bridged Speaker Output R L Make the speaker connections using speaker wire that is at least 14 gauge or heavier. As with any audio component, proper phasing of the amplifier and speakers is essential for strong bass response.
CH1 CH2 CH3 CH4 Fuse CH3 CH4 Bridged CH1 CH2 Bridged Speaker Output REM GND B+ REM GND B+ Fuse Bridged Speaker Output R L 4 Ohm Speaker 4 Ohm Speaker TWO CHANNEL BRIDGED SPEAKER CONNECTIONS FOUR CHANNEL BRIDGED SPEAKER CONNECTIONS S PEAKER CONNECTIONS (BRIDGED) The California amplifiers are capable of being bridged in a mono configuration.
REM GND B+ Fuse Bridged Speaker Output R L CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier.
Bass Boost 0 12 (Please note: If you intend to us e the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the "Off" setting in order to receive full range output) The California amplifiers are equipped with a built-in variable crossover network allowing you to select the crossover type (i.
T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself.
14 S PECIFICATIONS 100SX 200SX 400SX Output Power @ 4 Ohm 2 x 70W RMS 2 x 35W RMS 2 x 50W Bridged RMS @ 4 Ohm 1 x 100W THD @ RMS Power <0.07% Frequency Response 20Hz ~ 30Khz Signal To Noise >105.
15 S PECIFICATIONS 800SX 1200SX Output Power @ 4 Ohm 2 x 400W RMS 2 x 200W RMS 2 x 300W Bridged RMS @ 4 Ohm 1 x 600W THD @ RMS Power <0.07% Frequency Response 20Hz ~ 30Khz Signal To Noise >105dB.
LIMITED WARRANTY Profile Consumer Electronics, Inc. warrants this product to be free from defects in material and workmanship for a period of One (1) Year from the date of sale to the original consumer purchaser.
WARRANTY REPAIR POLICY In the unlikely event of product failure, the following procedures should be followed 1) The unit must be under the 1-year warranty period. 2) The unit must have no physical damage. 3) A copy of the original proof of purchase must be sent with the unit.
PROFILE CONSUMER ELECTRONICS, INC. 17625 FABRICA WAY CERRITOS, CA 90703 TEL: (714) 690-4949 FAX: (714) 690-4957 WORLD WIDE WEB: WWW.PROFILEUSA.COM By.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Profile 400SX c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Profile 400SX - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Profile 400SX, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Profile 400SX va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Profile 400SX, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Profile 400SX.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Profile 400SX. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Profile 400SX ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
