Manuel d'utilisation / d'entretien du produit 340 du fabricant Porter-Cable
Aller à la page of 15
Double Insulated Finishing Sander Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No.
2 WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.
3 2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 3. Avoid accidental starting. Be sure switch is OFF before plugging in.
4 SPECIFIC SAFETY RULES AND SYMBOLS 1. Always disconnect the sander cord plug from the power circuit before changing abrasive sheets. 2. Sanding of lead-based paint is not recommended. Lead-based paint should only be removed by a professional. 3. Some wood contains preservatives which can be toxic.
5 ADDITIONAL SAFETY RULES FOR P AINT REMOV AL WARNING: Extreme care should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause irreversible brain and nervous system damage; young and unborn children are particularly vulnerable.
6 MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only.
7 Naturally, in all sanding operations, best results will be obtained if you select the proper size and type of abrasives. Only garnet, aluminum oxide and silicon carbide are recommended for use with finishing sanders. Before starting to work, make sure you have the right abrasive for the material on which the sander is to be used.
8 Fig. 6 Fig. 7 P APER PUNCH A Paper Punch is provided with Model 340 Sander. The punch is used to make eight holes through the abrasive. These holes allow the sanding dust to be extracted directly through the pad. The punch can be mounted to a workbench or wall using four No.
OPERA TION TO ST ART AND STOP SANDER 1. CAUTION: Make certain the switch is in the “OFF” position, and the power source is the same as that specified on the tool’s nameplate. 2 . Connect the sander to the power source. 3. Lift sander off the work and hold it firmly when switching the motor “ON” and “OFF”.
NOTE: A slight twisting action will ease removal and reassembly. Tap container lightly to remove compacted dust. DO NOT WASH CONTAINER. Dry compressed air may be used to blow out container. CAUTION: Wear safety glasses while using compressed air. ACCESSOR Y P ADS Model 340 is supplied with a Standard Profile, PSA (Pressure Sensitive Adhesive) Pad.
11 USING THE SANDER SANDING PROCEDURE The normal weight of the machine is sufficient for efficient sanding. Do not put additional pressure on the machine. This would only slow down the speed of the pad, reducing the sanding efficiency and put an additional burden on the motor.
12 REMOVING P AINT AND V ARNISH CAUTION: Read and follow all instructions in the ADDITIONAL SAFETY RULES FOR PAINT REMOVAL section of this manual. Your sander will do a good job of removing old paint and varnish if two precautions are taken. First, be sure to use a coarse, open coat abrasive to avoid the usual clogging of the abrasive surfaces.
13 Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the service station for immediate service.
14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase.
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Porter-Cable 340 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Porter-Cable 340 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Porter-Cable 340, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Porter-Cable 340 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Porter-Cable 340, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Porter-Cable 340.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Porter-Cable 340. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Porter-Cable 340 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
