Manuel d'utilisation / d'entretien du produit 33-413 du fabricant Porter-Cable
Aller à la page of 28
INSTRUCTION MANUAL P ART NO. 424-03-651-0019 - 06-20-05 Copyright © 2004 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury .
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury .
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage.
5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions.
Fig. 1 1. 3/8-16x1" Hex Head Screw (12) 2. 1/4-20x7/8" Round Head Screw (15) 3. 1/2-20x1/2" Hex Head Screw (4) 4. 3/8" Flat Washer (12) 5. 9/32" Flat Washer (15) 6. 3/8" Lockwasher (12) 7. 1/4" Lockwasher (4) 8. 3/8-16 Hex Nut (12) 9.
7 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose).
8 ELEV A TING CRANK HANDLE Assemble elevating crank handle (A) Fig. 6 to rod in front of base using the r oll pin (B). TRACK-ARM LOCK Assemble track-arm lock handle (A) to the overarm (Fig. 7), and tighten set screw (B). Lock handle (A) should be tight when in the position shown in Fig.
9 CUTTINGHEAD AND CROSS-CUT STOP TO TRACK-ARM 1. Remove two screws (A) and end cap (B) from track- arm, Fig. 8. 2. Hold cuttinghead assembly (D) Fig. 9, with both hands and insert the ball bearings (E) into the track- arm, as shown. Push cuttinghead all the way onto track-arm and tighten clamp knob (F).
10 ST AR TER BOX TO BASE 1. Assemble bracket (A) to the bottom of the right side of saw base, (Fig. 12), using the 1/4-20x1/2" hex head screw (B), 1/4" lockwasher (D), and 1/4-20 nut (E).
11 ADJUSTING T ABLE TOP P ARALLEL TO TRACK-ARM For accurate work the track-arm must be parallel to the table top at all points. T o check and adjust: 1. Move the motor and cuttinghead assembly (A) to the vertical position (Fig. 18). Position saw arbor (B) Fig.
12 3. IMPORT ANT : T o prevent arbor nut fr om spinning when blade stops, place the 1-1/16" wrench (C) Fig. 23 on flats of arbor and firmly tighten arbor nut (A) with the 1-5/8" box end spanner wrench (D) (left handed thread). Firmly tighten set scr ew (E).
13 4. Attach eyelet (H) Fig. 30 of cable assembly (C) to "S" bracket (E). 5. NOTE: T o prevent pr emature wear of r etur n reel cable, position the return reel so that the cable does not rub against the wall of the return reel. Fig. 30 H C E Fig.
14 T AKING SIDE MOTION OUT OF OVER-ARM 1. Loosen hex nuts (A) and gib adjusting scr ews (B) and (C) Fig. 31. 2. Loosen nuts (D) Fig. 31, and adjust bolts (E), so that base wraps around column secur ely . If column is tight in base, turn bolts (E) clockwise to loosen.
15 Fig. 33 Fig. 34 G ADJUSTING TRACK RODS Each track rod (A, B, C, D) Fig. 34 can be adjusted individually to present a new bearing surface. Adjust the track rods one at a time as follows: 1. Remove end cap (E) Fig. 35, cross-cut stop (F) and cutterhead assembly (G), from the track-arm (Fig.
16 ADJUSTING BLADE SQUARE WITH T ABLE TOP 1. Remove blade guard and place saw blade in cut-of f position over fixed portion of table. 2. Place a square (A) Fig. 36, against saw blade. Be sure squar e is on the table surface, and between the gullets of the teeth, not against the saw teeth.
17 1. Place a square (A) Fig. 40 against fence (B), and lower cuttinghead (C) so that saw blade just clears table top. 2. Pull cuttinghead (C) Fig. 40, along square (A). If saw blade does not travel parallel to the square, the following adjustment is necessary .
18 Even though the cuttinghead travel may be perfectly aligned at 90 degrees to the fence, the blade itself may not be 90 degrees or squar e with the fence, (Fig. 42). This condition is known as "heeling."T o check and adjust: 1. Cross-cut a board and see on which side of the cut board saw teeth marks appear .
19 ADJUSTING BLADE GUARD On all ripping and plowing operations, the back part of the blade guard is lower ed so that it just clears the material. This will prevent the material fr om being lifted off the table. Also, lower the kickback r od (A) Fig. 46, so that the kickback fingers are 1/8" below surface of material.
20 ADJUSTING TENSION ON CUTTINGHEAD RETURN ASSEMBL Y The cuttinghead return assembly is properly tensioned when ther e is just enough cable tension to return the cuttinghead (A) Fig. 49, without excessive force, to the r ear of the track arm (B) after completion of the cut.
21 CROSS-CUTTING Cross-cutting consists of supporting the workpiece against the fence and pulling the saw blade through the material at right angles to it. When cross-cutting, the track arm should be indexed at “0” and the track arm clamp handle tightened.
22 COMPOUND MITER CUTTING Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation ar e similar to miter cut ting except that the blade is first tilted to the desired angle on the bevel scale befor e it is clamped in place.
23 PUSH STICK Make from 1/2 ″ OR 3/4 ″ WOOD or thickness less than width of material to be cut. Cut her e to push 1/4 ″ wood. Cut her e to push 1/2 ″ wood.
24 TROUBLESHOOTING GUIDE For assistance with your tool, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).
A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
26 NOTES.
27 NOTES.
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Porter-Cable 33-413 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Porter-Cable 33-413 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Porter-Cable 33-413, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Porter-Cable 33-413 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Porter-Cable 33-413, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Porter-Cable 33-413.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Porter-Cable 33-413. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Porter-Cable 33-413 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
