Manuel d'utilisation / d'entretien du produit G8 du fabricant Pontiac
Aller à la page of 334
Seats and Restraints ......... 1 - 1 Front Seats .................... 1 - 2 Rear Seats .................... 1 - 5 Safety Belts ................... 1 - 5 Airbag System .............. 1-19 Child Restraints ............. 1-32 Keys, Doors and Windows ....
GENERAL MOTORS, GM, the GM Emblem, PONTIAC, the PONTIAC Emblem, are registered trademarks of General Motors Corporation, and the name G8 is a trademark of General Motors Corporation. This manual includes the latest information at the time it was printed.
Index To quickly locate information about the vehicle use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Cautions and Notices There are a number of safety cautions in this book.
✍ NOTES iv Preface 2008 - Pontiac G8 Owner Manual.
Seats and Restraints Front Seats Front Seats ....................... .1-2 Manual Seats .................... .1-2 Power Seat(s) .................... .1-2 Lumbar Seat Adjustment . . . .1-2 Reclining Seatbacks .......... .1-3 Head Restraints ............
Front Seats A. Head Restraints on page 1-4 . B. Lumbar Seat Adjustment on page 1-2 . C. Reclining Seatbacks on page 1-3 . D. Power Seat(s) on page 1-2 . E. Manual Seats on page 1-2 . Manual Seats { CAUTION You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving.
Reclining Seatbacks { CAUTION You can lose control of the vehicle if you try to adjust the seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. The rear seats have head rests in the outboard seating positions.
Heated Seats On vehicles with heated front seats, the controls are located on the center console. To operate the heated seats the ignition must be on. L (Heated Seat): Press to turn on the heated seat.
{ CAUTION It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does.
Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
First, before you or your passenger(s) wear a safety belt, there is important information you should know. Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs.
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { CAUTION You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
{ CAUTION You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
{ CAUTION You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury. You might also slide under the lap belt.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. Here is how to wear a lap-shoulder belt properly. 1. Adjust the seat so you can sit up straight. To see how, see “Seats” in the Index. 2. Pick up the latch plate and pull the belt across you.
To unlatch the belt, push the button on the buckle. The belt should go back out of the way. When the safety belt is not in use, slide the latch plate up the safety belt webbing. The latch plate should rest on the stitching on the safety belt, near the guide loop on the side wall.
There is one guide for each outboard passenger position in the rear seat. Here is how to install a comfort guide to the safety belt: 1. Pull the elastic cord out from the side of the seatback to remove the guide from its storage pocket. 2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide.
4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that you can take them out of the guide.
Safety Belt Check Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
After a minor crash, replacement of safety belts may not be necessary. But the safety belt assemblies that were used during any crash may have been stressed or damaged. See your dealer/retailer to have the safety belt assemblies inspected or replaced.
Here are the most important things to know about the airbag system: { CAUTION You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
{ CAUTION Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide.
The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows. { CAUTION If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
• If the vehicle hits a narrow object (like a pole), the airbags could inflate at a different crash speed than if the vehicle hits a wide object (like a wall). • If the vehicle goes into an object at an angle, the airbags could inflate at a different crash speed than if the vehicle goes straight into the object.
What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator. Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy. The inflator, the airbag, and related hardware are all part of the airbag module.
The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags. Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicle.
Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible in the rearview mirror when you start the vehicle. The words ON and OFF, or the symbol for on and off, will be visible during the system check.
CAUTION (Continued) Even if the passenger sensing system has turned off the right front passenger frontal airbag, no system is fail-safe. No one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off.
vehicle head restraint. If this happens, adjust the head restraint. See Head Restraints on page 1-4 . Remove any additional material from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers before reinstalling or securing the child restraint.
{ CAUTION If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger’s seat may not have the protection of the airbag(s).
Servicing Your Airbag-Equipped Vehicle Airbags affect how your vehicle should be serviced. There are parts of the airbag system in several places around your vehicle. Your dealer/retailer and the service manual have information about servicing your vehicle and the airbag system.
In addition, the vehicle has a passenger sensing system for the right front passenger position, which includes sensors that are part of the passenger’s seat.
Replacing Airbag System Parts After a Crash { CAUTION A crash can damage the airbag systems in your vehicle. A damaged airbag system may not work properly and may not protect you and your passenger(s) in a crash, resulting in serious injury or even death.
The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below fit test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
{ CAUTION Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
{ CAUTION Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types.
Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child’s body with the harness.
Securing an Add-On Child Restraint in the Vehicle { CAUTION A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys.
Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints with top tethers are designed for use with or without the top tether being attached.
The top tether anchors are located on the rear seatback filler panel. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
{ CAUTION Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash.
2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor.
If the position you are using has a fixed headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint. If the position you are using has a fixed headrest or head restraint and you are using a single tether, route the tether over the head restraint.
New parts and repairs may be necessary even if the LATCH system, was not being used at the time of the crash. Securing Child Restraints (Rear Seat) When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle.
Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessary. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
Securing Child Restraints (Right Front Seat) This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-38 . In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Keys, Doors and Windows Keys Keys .................................. .2-2 Remote Keyless Entry (RKE) System .................. .2-3 Remote Keyless Entry (RKE) System Operation . . .2-4 Remote Vehicle Start ......... .2-6 Doors and Locks Door Locks ...
Keys { CAUTION Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
Remote Keyless Entry (RKE) System The Remote Keyless Entry (RKE) system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions will work up to 195 feet (60 m) away, however, the operating range may be less while the vehicle is running. There are other conditions which can affect the performance of the transmitter.
L (Vehicle Locator/Panic Alarm): Press and release one time to locate your vehicle. The exterior lamps will flash and the horn will chirp. Press and hold L for at least two seconds to sound the panic alarm. The horn will sound and the turn signals will flash until L is pressed again or the key is placed in the ignition and turned to ON/RUN.
Remote Vehicle Start Your vehicle may have this feature which allows you to start the engine from outside the vehicle. / (Remote Vehicle Start): This button will be on the RKE transmitter if you have remote start. To enable and disable remote start, see “Remote Start” under DIC Vehicle Customization on page 4-32 .
Extending Engine Run Time To extend the engine run time by 10 minutes, repeat Steps 1 and 2 while the engine is still running. The engine run time can only be extended if it is the first remote start since the vehicle has been driven. Remote start can be extended one time.
Doors and Locks Door Locks { CAUTION Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
The door lock cylinder turns freely when either the wrong key is used, or the correct key is not fully inserted. The free turning door lock feature prevents the lock from being forced open. To reset the lock, turn it to the vertical position with the correct key fully inserted.
Trunk { CAUTION It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO.
There is an emergency trunk release handle located inside the trunk on the trunk latch. Access the release handle by folding the rear seat center seatback. See Rear Seat Operation on page 1-5 . Pull the release handle to open the trunk from the inside.
Immobilizer Operation Your vehicle has a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition. The system is disarmed when the key is turned to ON/RUN. You do not have to manually arm or disarm the system.
3. Insert and turn the new section (A) to ON/RUN within five seconds of removing the original key. 4. Turn the new section (A) to LOCK/OFF. Section (A) is now programmed. To program a new section (B): 1. Turn the ignition to ON/RUN with the new section (A).
How to Detect a Tamper Condition If K is pressed and the horn sounds, an attempted break-in has occurred while the system was armed. If the alarm has been activated, the Alarm Activated message appears followed by a message showing what location set off the alarm.
Power Windows A. Power Window Switches B. Rear Window Lockout Switch The power window switches (A) for all doors are located on the center console. The switches work when the ignition is in ON/RUN, ACC/ACCESSORY, or in Retained Accessory Power (RAP). See Retained Accessory Power (RAP) on page 8-3 .
Mirrors Manual Rearview Mirror The vehicle has a manual rearview mirror with a compass display and OnStar ® control buttons located at the bottom of the mirror. See your dealer/retailer for more information on the system and how to subscribe to OnStar.
Compass Variance The mirror is set to zone eight. Adjust the compass to compensate for compass variance if you live outside zone eight. Under certain conditions, such as during a long-distance, cross-country trip, it is necessary to adjust for compass variance.
Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, push the mirror toward the vehicle. Push the mirror outward, to return to its original position. Outside Convex Mirror { CAUTION A convex mirror can make things (like other vehicles) look farther away than they really are.
Storage Storage Glove Box ......................... .3-1 Center Console Storage .... .3-1 Convenience Net ............... .3-1 Storage Glove Box To open, lift the handle up. Use the key to lock and unlock. Center Console Storage A storage area is provided under the front armrest.
To create a pouch, attach the four corner loops (A) to each of the two top hooks. Attach the nets center loops (B) to the bottom hooks. 3-2 Storage 2008 - Pontiac G8 Owner Manual.
Instruments and Controls Instrument Panel Overview Instrument Panel Overview .......................... .4-2 Hazard Warning Flashers ........................... .4-4 Horn .................................. .4-4 Tilt Wheel .......................... .4-4 Turn Signal/Multifunction Lever .
Instrument Panel Overview 4-2 Instruments and Controls 2008 - Pontiac G8 Owner Manual.
The main components of the instrument panel are the following: A. Turn Signal/Multifunction Lever on page 4-4 . B. Audio Steering Wheel Controls on page 6-23 and DIC Operation and Displays on page 4-23 . C. Instrument Panel Cluster on page 4-11 . D. Audio Steering Wheel Controls on page 6-23 .
Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press | again to turn the flashers off.
Cruise Control For vehicles with cruise control, the lever is located on the left side of the steering wheel. The cruise control maintains the vehicle’s speed without having your foot on the accelerator pedal. The cruise control only works at speeds above 21 mph (33 km/h) (V6 engines) or above 24 mph (38 km/h) (V8 engines).
3. Turn the band down to SET − and then release it. The CRUISE ACTIVE light comes on in the instrument panel cluster. 4. Take your foot of f the accelerator pedal. If the vehicle is in cruise control and the Electronic Stability Program (ESP) becomes active, the cruise control automatically disengages.
Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle speed. When going downhill, you might have to brake or shift to a lower gear to keep the vehicle speed down.
Windshield Wipers The windshield wiper/washer lever is located on the right side of the steering column. The ignition must be turned to the ON/RUN or ACC/ACCESSORY position to use the windshield wipers. Move the lever to the following positions: z (Mist): Hold the lever in this position for continuous wiping cycles.
{ CAUTION In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. Accessory Power Outlet(s) The accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular phone.
Warning Lights, Gages, and Indicators This section describes the warning lights and gages on the vehicle. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gages could prevent injury.
Instrument Panel Cluster The instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you have, and many other things you will need to drive safely and economically.
Speedometer The speedometer can display your speed in both miles per hour (MPH) and kilometers per hour (km/h). You can select between MPH and km/h using the UNITS display in the DIC. See DIC Operation and Displays on page 4-23 for more information. Tachometer The tachometer displays the engine speed in revolutions per minute.
Airbag Readiness Light There is an airbag readiness light which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions.
Passenger Airbag Status Indicator The vehicle has a passenger sensing system. The rearview mirror has a passenger airbag status indicator. When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
{ CAUTION Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off.
Driving while this light is on could drain your battery. If you must drive a short distance with the light on, be sure to turn off all accessories, such as the radio and air conditioner. The Alternator message will remain until 3 (Trip/Fuel) or 8 (Enter) are pressed, but the light will remain until the problem is fixed.
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light will come on briefly, as a check, when you start your vehicle. If it does not, have your vehicle serviced so that the light works properly when it needs to.
Tire Pressure Light TPMS Light This light comes on briefly when the engine is started and provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is Solid This light will also come on when one or more of your tires are significantly underinflated.
Malfunctions often are indicated by the system before any problem is apparent. Heeding the light can prevent more serious damage to your vehicle. This system assists your service technician in correctly diagnosing any malfunction.
• If you just drove through a deep puddle of water, your vehicle’s electrical system might be wet. The condition is usually corrected when the electrical system dries out. A few driving trips should turn the light off. • If you recently changed brands of fuel, be sure to fuel your vehicle with quality fuel.
Security Light For information regarding this light and the vehicle’s security system, see Content Theft-Deterrent on page 2-13 . Fog Lamp Light The fog lamp light will come on when the fog lamps are in use. The light will go out when the fog lamps are turned off.
Oil Pressure Gage The gage shows the engine oil pressure. It is located in the center of the instrument panel. { CAUTION Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches fire. You or others could be burned.
Driver Information Center (DIC) The DIC displays information about your vehicle. It also displays warning messages if a system problem is detected. The DIC also allows some features to be customized. See DIC Vehicle Customization on page 4-32 for more information.
Speedometer Press 3 until the speedometer is displayed. The speedometer shows how fast the vehicle is moving in either miles per hour (MPH) or kilometers per hour (km/h). To switch between English and metric measurements, see “UNITS” later in this section.
distance. When driving, the computer constantly updates the time to arrival, based on changing driving speeds. Use the thumbwheel to adjust the distance any time this display is shown. Time to go is shown in hours and minutes and is only shown if the distance to go is more than zero.
Preset 2: Default setting 45 MPH (72 km/h) Preset 3: Default setting 55 MPH (89 km/h) Preset 4: Default setting 70 MPH (113 km/h) The selection is set automatically after a few seconds. The corresponding value of the presets will be shown on the display.
Underspeed Chime If an OverSpeed warning appeared and the vehicle’s speed drops below the set value, you will hear a chime. The underspeed chime can be turned on or off through the vehicle customization. See DIC Vehicle Customization on page 4-32 for more information.
{ Alarm Activated This message is displayed when the content theft-deterrent system was activated by an attempted break-in. The messages may also include the location on the vehicle where the break-in was attempted. See Content Theft-Deterrent on page 2-13 for more information.
illuminated. If the oil level is normal, have the system checked at your dealer/retailer. You can press 3 or 8 to acknowledge that you received the message, but : Check Oil will continue to appear in the bottom of the DIC display until the vehicle has been serviced.
y OverSpeed This message is displayed when the vehicle’s speed is greater than the set OverSpeed value. See “OverSpeed” under DIC Operation and Displays on page 4-23 .
Service Charging System This message is displayed when there is a fault in the battery charging system, see your dealer/retailer. You can press 3 or 8 to acknowledge that you received the message, but " Low Batt will continue to appear in the bottom of the DIC display until the vehicle has been serviced.
You can press 3 or 8 to acknowledge that you received the message, but ESP OFF will continue to appear in the bottom of the DIC display until the vehicle has been serviced. 7 Check XX Tire Pressure This message is displayed when the inflation pressure is low or very low in the indicated tire.
The following items are part of the main customization menu. • Exit • Reset settings • Security • Lighting • Trip Computer • Language • Remote key See the information following for detailed descriptions of the items available under each menu item.
All doors in park: All doors will unlock when you put the shift lever into PARK (P). Auto lock If you select Auto lock you will be able to choose when you want the doors to lock automatically. At vehicle speed: The doors will lock when the vehicle speed is at or above 8 mph (13 km/h).
• Digital speedo (speedometer) • Pressure Units • Rest reminder Underspeed Chime If you select Underspeed Chime you will be able to enable or disable the underspeed chime feature. See DIC Operation and Displays on page 4-23 for more information.
OnStar ® System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location.
• AccidentAssist • Remote Door Unlock/Vehicle Alert • OnStar Vehicle Diagnostics • GM Goodwrench On Demand Diagnostics • OnStar Hands-Free Calling with 30 complimentary minutes • OnStar Virtual Advisor (U.
How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy.
Lighting Lighting Exterior Lamps Controls .... .5-1 Daytime Running Lamps (DRL) ................... .5-2 Automatic Headlamp System ............................ .5-2 Fog Lamps ........................ .5-3 Instrument Panel Brightness ..................
; (Parking Lamps): Turns on the parking lamps together with the following: • Taillamps • License Plate Lamps • Instrument Panel Lights • Sidemarker Lamps 2 (Headlamps): Turns on the headlamps .
The vehicle has a light sensor located on top of the instrument panel. Do not cover the sensor or the headlamps will come on when they are not needed. The system may also turn on the headlamps when driving through a parking garage or tunnel. Fog Lamps For vehicles with this feature, it provides better visibility in foggy or misty conditions.
Dome Lamp(s) + (On/Off): Press to turn the lamp on or off. & (Door): Press this button in and the lamps automatically turn on when a door is opened, the vehicle is unlocked, or the key is removed from the ignition. The lamps dim to off after all the doors are closed.
Infotainment Audio System(s) Audio System(s) ................ .6-1 Setting the Clock ............... .6-2 Radio(s) ............................ .6-3 Using an MP3 .................. .6-19 Theft-Deterrent Feature .... .6-23 Audio Steering Wheel Controls .
Notice: Before adding any sound equipment to your vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer/retailer. Also, check federal rules covering mobile radio and telephone units.
Radio(s) Radio with Single CD Player Infotainment 6-3 2008 - Pontiac G8 Owner Manual.
The vehicle has one of these radios as its audio system. Playing the Radio } (Power): Press to turn the system on and off. Radio with Single CD Player Volume: The volume knob is located on the center of the radio. Turn to adjust the volume. 0 (Mute): Press to immediately stop the volume.
Radio with Six-Disc CD Player u (Volume/Mute): Turn to adjust the volume. Press to immediately stop the volume. While the volume is off, MUTED displays. To cancel Mute, do one of the following: • Press u . • Increase the radio volume. • Turn the radio off and on.
3. Press the MENU knob to enter the Seek Sens setting. 4. Turn the MENU knob and highlight either Local, Distance, or Auto. 5. Select the BACK option or wait eight seconds to exit the menu. Setting Preset Stations Up to 30 stations (six FM1, six FM2, six AM, six FM ASM, and six AM ASM), can be programmed.
To adjust the bass and treble on the radio with a six-disc CD player: 1. Press the MENU knob to enter the Option Menu, Audio is highlighted. 2. Press the MENU knob to enter the Audio menu. 3. Turn the MENU knob until Bass or Treble highlights. 4. Press the MENU knob to enter the Bass or Treble settings.
5. Turn the volume knob to adjust the BALANCE or FADE setting. 6. Press the volume knob to save and exit the setting. 7. Select the BACK option or wait eight seconds to exit the menu. To adjust the balance and fade on the radio with a six-disc CD player: 1.
Radio Message Security Lockout Active: This message displays when the coded security system has been activated. Take the vehicle to your dealer/retailer for service. Using the CD Player The CD player plays standard sized CDs. Using CDs of a different size can damage the drive or disc, even if an adapter is used.
To insert multiple CDs: 1. Press and hold # LOAD for more than two seconds, a beep sounds and Loading All Discs displays. 2. The display, the beeps, and the load indicator light prompts when to insert each CD. 3. Insert a CD label side up partway into the slot.
To use random with the radio with a single CD player, press RDM to randomly play all tracks on the CD. Press RDM again to cancel this function. To use random with the radio with a six-disc CD player, press the softkey below RANDOM to select between. • RANDOM TRACK • RANDOM DISC DISPLAY MODE: The display modes for CD operation can be changed.
CD: Press to start playback of a CD already in the drive if it was not the last audio source. CD j : Press to pause and resume playback of the CD. Press to start playback of a CD already in the player if it was not the last audio source. j (Pause): Press to pause and resume playback of the CD.
The use of CD lens cleaners for CDs is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD player mechanism.
The rear auxiliary input connector is located on the back of the radio. See your dealer/retailer for more information about this feature. To disable the rear auxiliary input on the radio with a single CD player: 1. Press the volume knob to enter the Option Menu, AUDIO is highlighted.
Additional Features Help Prompts: Allows help information to be displayed for eight seconds after the request for that button or feature has been made. To enable or disable help prompts: 1. Press the MENU knob to enter the Options Menu. 2. Turn the MENU knob until Help Prompts highlights.
Startup Screen: To enable or disable the startup screen on the radio with a six-disc CD player: 1. Press the MENU knob to enter the Options Menu. 2. Turn the MENU knob until Welcome highlights. 3. Press the MENU knob to access the Welcome menu. 4. Turn the MENU knob to change the setting to On or Off.
Speed Dependent Volume (SDV): The SDV system automatically adjusts the radio volume to compensate for driving noise. The SDV system can only be adjusted while the radio is on. As the speed of the vehicle increases or decreases, the radio volume increases or decreases.
3. Press the volume knob to enter the AUD SETUP menu. 4. Turn the volume knob until DDL highlights. 5. Press the volume knob to enter the DDL setting. 6. Turn the volume knob to adjust the DDL setting. 7. Press the volume knob to save and exit the setting.
Personal Identity Memories (Radio with Six-Disc CD Player) Personal Identity Memories are coded to the vehicle’s keys. Only two keys can be coded. The settings are stored by the vehicle and are unique to each key.
To record an MP3 disc: • Record the MP3 files onto a CD-R or CD-RW disc. • Record playlists with an .m3u or .wpl extension. • Do not mix standard audio and MP3 files on the same disc. • Record the entire disc at once. • Finalize the disc when recording an MP3 disc with multiple sessions.
Preprogrammed Playlists Playlists are accessed before files or folders in the root directory. Preprogrammed playlists created by WinAmp™, MusicMatch™, or Real Jukebox™ software can be accessed and are treated as special folders containing compressed audio song files.
REPEAT: Select to repeat tracks or folders. To use REPEAT: 1. Press the softkey below the REPEAT label to display the different repeat modes. 2. Press the softkey below REPEAT TRACK, REPEAT DISC, or REPEAT FOLDER to chose that mode. 3. Press the softkey below the active repeat mode to cancel the repeat mode.
l (Forward): Press to go to the next track or press l multiple times until the desired track is reached. g (Reverse): Press to go back to the start of the current track or press g multiple times until the desired track is reached. Theft-Deterrent Feature The radio has an electronically coded security system that links the radio to the vehicle.
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Climate Controls Climate Controls Climate Control System ..... .7-1 Automatic Climate Control System ............................ .7-4 Outlet Adjustment .............. .7-8 Climate Controls Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system.
Air Delivery Mode Control Use the right knob to select from the following modes. 0 (Vent): Air is directed to the instrument panel outlets. 1 (Bi-Level): Air is divided between the instrument panel outlets and the floor outlets. d (Floor): Air is directed to the floor outlets with some air directed to the windshield and side window outlets.
Recirculation / (Recirculation): Press to change the air intake between recirculated air and outside air. An indicator light comes on when the recirculation is on.
Automatic Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. For vehicles with the remote start feature, the climate control system will turn on with a remote start. See Remote Vehicle Start on page 2-6 .
Manual Operation Fan Control + A − (Fan): Press + or − to increase or decrease the fan speed. The fan speed and indicator appears in the display. The climate control system sets the fan speed automatically. When the fan speed is adjusted the system goes into semi-automatic operation.
Select from the following modes: 0 (Vent): Air is directed to the instrument panel outlets. 1 (Bi-Level): Air is divided between the instrument panel outlets and the floor outlets. Cooler air is directed to the upper outlets and warmer air to the floor outlets.
Do not use the recirculation mode if occupants are smoking. The recirculation mode cannot be turned on in defrost mode. If / is pressed, the indicator light flashes three times and recirculation stays off. Pollution Mode: Press and hold the / button for four seconds to turn the pollution mode on or off.
By monitoring the solar radiation, the air inside the vehicle and air moving across the outside sensor, the selected temperature can be maintained while using the AUTO mode by adjusting the temperature, fan speed, and air delivery system. The system may also supply cooler air to the side of the vehicle facing the sun.
Driving and Operating Starting and Operating Your Vehicle New Vehicle Break-In ........ .8-2 Ignition Positions ............... .8-2 Retained Accessory Power (RAP) .................... .8-3 Starting the Engine ............ .8-4 Engine Coolant Heater .
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one constant speed, fast or slow, for the first 500 miles (805 km).
A (LOCK/OFF): This is the only position from which you can remove the key. This locks the steering wheel, ignition and automatic transmission. On vehicles with an automatic transmission, the shift lever must be in P (Park) to turn the ignition switch to the LOCK/OFF position.
Starting the Engine Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. To restart when you are already moving, use N (Neutral) only. Notice: Do not try to shift to P (Park) if your vehicle is moving. If you do, you could damage the transmission.
When the engine starts, let go of the key and accelerator. If the vehicle starts briefly but then stops again, do the same thing. This clears the extra gasoline from the engine. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts.
The length of time the heater should remain plugged in depends on several factors. Ask a dealer/retailer in the area where you will be parking the vehicle for the best advice on this. Automatic Transmission Operation The shift lever is located on the center console between the front seats.
ease pressure on the shift lever and push the shift lever all the way into P (Park) while maintaining brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting Out of Park on page 8-11 . Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission.
Sport Shift Mode The automatic transmission has a Sport Shift Mode. When you are in the Sport Shift Mode the vehicle will still shift automatically. The transmission may remain in a gear longer than it would in the normal driving mode based on braking, throttle input, and vehicle lateral acceleration.
When accelerating the vehicle from a stop in snowy and icy conditions, 1st, 2nd or 3rd gear starts can be selected from a standing start. This is useful for gentle acceleration on slippery surfaces. To return to Normal Shift mode, slide the shift lever over from the right quadrant to the left into D (Drive).
Shifting Into Park (Automatic Transmission) { CAUTION It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Then, see if you can move the shift lever away from P (Park) without first pushing the button. If you can, it means that the shift lever was not fully locked into P (Park).
Engine Exhaust { CAUTION Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • The exhaust system sounds strange or different.
{ CAUTION It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly.
Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 17,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with about 250,000 people injured.
And, of course, actual stopping distances vary greatly with the surface of the road, whether it is pavement or gravel; the condition of the road, whether it is wet, dry, or icy; tire tread; the condition of the brakes; the weight of the vehicle; and the amount of brake force applied.
You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel. ABS can change the brake pressure faster than any driver could.
on and the ESP CTRL message will be displayed at the bottom of the DIC. The STABILITY CONTROL ASSISTANCE message will remain on while the system is working until the 3 button is pressed to display the trip computer. The ESP CTRL message stays on at the bottom of the DIC while the system is working.
When this light and the STABILITY CTRL OFF message is on briefly and the ESP OFF message is displayed at the bottom of the DIC, the system will not limit wheel spin. If the ESP OFF message is always displayed at the bottom of the DIC when the button is pressed to turn the system on or off, the system needs repair.
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips It is important to take curves at a reasonable speed. A lot of the “driver lost control” accidents mentioned on the news happen on curves.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Passing Passing another vehicle on a two-lane road can be dangerous. To reduce the risk of danger while passing: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. • Watch for traff ic signs, pavement markings, and lines that could indicate a turn or an intersection.
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration, or braking, including reducing vehicle speed by shifting to a lower gear. Any sudden changes could cause the tires to slide. You might not realize the surface is slippery until your vehicle is skidding.
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or flowing water.
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer .
{ CAUTION Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Driving on Snow or Ice Most of the time, those places where the tires meet the road probably have good traction. However, if there is snow or ice between the tires and the road, you can have a very slippery situation. You have a lot less traction, or grip, and need to be very careful.
{ CAUTION Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe.
Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right to clear the area around the front wheels. Turn off any stability system. See Electronic Stability Program on page 8-16 . Then shift back and forth between REVERSE (R) and a forward gear, spinning the wheels as little as possible.
Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will find the label attached near the door lock post.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, the load from your trailer will be transferred to your vehicle.
A. Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg). B. Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg). C. Available Cargo Weight = 0 lbs (0 kg). Refer to the vehicle’s Tire and Loading Information label for specific information about the vehicle’s capacity weight and seating positions.
If you put things inside the vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. { CAUTION Things you put inside the vehicle can strike and injure people in a sudden stop or turn, or in a crash.
Gasoline Octane If your vehicle has a V8 engine, use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, you might notice an audible knocking noise when you drive, commonly referred to as spark knock.
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel.
Filling the Tank { CAUTION Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 4-18 . { CAUTION If a fire starts while you are refueling, do not remove the nozzle.
Vehicle Service and Care Service Service .............................. .9-2 Accessories and Modifications .................... .9-3 California Proposition 65 Warning ........................... .9-3 California Perchlorate Materials Requirements ....
Uniform Tire Quality Grading .......................... .9-59 Wheel Alignment and Tire Balance .......................... .9-60 Wheel Replacement ......... .9-61 Tire Chains ...................... .9-62 Tire Changing If a Tire Goes Flat ........... .9-62 Tire Sealant and Compressor Kit (V8 Engine) .
Accessories and Modifications When non-dealer/non-retailer accessories are added to your vehicle they can affect your vehicle’s performance and safety, including such things as, airbags, braking, s.
Doing Your Own Service Work { CAUTION You can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have suff icient knowledge, experience, the proper replacement parts, and tools before you attempt any vehicle maintenance task.
Owner Checks { CAUTION An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION Things that burn can get on hot engine parts and start a fire.
Engine Compartment Overview When you open the hood, this is what you will see: A. Engine Compartment Fuse Block. See Engine Compartment Fuse Block on page 9-35 . B. Coolant Reservoir and Dipstick. See Cooling System on page 9-17 . C. Engine Oil Fill Cap.
A. Engine Compartment Fuse Block. See Engine Compartment Fuse Block on page 9-35 . B. Coolant Reservoir and Dipstick. See Cooling System on page 9-17 . C. Engine Oil Dipstick. See “Checking Engine Oil” under Engine Oil on page 9-8 . D. Engine Oil Fill Cap.
Engine Oil Checking Engine Oil It is a good idea to check the engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 9-6 for the location of the engine oil dipstick.
What Kind of Engine Oil to Use Look for three things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. Look for and use only an oil that meets GM Standard GM6094M. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle.
If you are in an area of extreme cold, where the temperature falls below − 20°F ( − 29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both provide easier cold starting and better protection for the engine at extremely low temperatures.
After changing the engine oil, reset the system: 1. Turn the ignition key to ON/RUN with the engine off. 2. Fully press and release the accelerator pedal three times within five seconds. If the Service Engine Oil message does not appear, the system is reset.
How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/filter, remove the filter from the vehicle and lightly shake the filter to release loose dust and dirt. If the filter remains caked with dirt, a new filter is required. To inspect or replace the engine air cleaner/filter: 1.
Notice: If the air cleaner/filter is off, a backfire can cause a damaging engine fire. And, dirt can easily get into your engine, which will damage it. Always have the air cleaner/filter in place when you are driving. Automatic Transmission Fluid It is not necessary to check the transmission fluid level.
What to Use Use a mixture of one-half clean, drinkable water and one-half DEX-COOL ® coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. { CAUTION Adding only plain water to the cooling system can be dangerous.
Checking Coolant The coolant reservoir and dipstick is located in the engine compartment on the passenger side of the vehicle. See Engine Compartment Overview on page 9-6 for more information on location. 1. Turn of f the ignition. 2. Turn the coolant dipstick cap one-eighth of a turn counterclockwise and slowly pull the dipstick straight up.
Engine Overheating There is an engine coolant temperature warning light on your vehicle’s instrument panel. See Engine Coolant Temperature Gage on page 4-17 . If Steam Is Coming From Your Engine { CAUTION Steam from an overheated engine can burn you badly, even if you just open the hood.
If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning does not come back on, you can drive normally. If the warning continues and you have not stopped, pull over, stop, and park your vehicle right away.
A. Coolant Reservoir and Dipstick B. Radiator Pressure Cap { CAUTION An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
{ CAUTION Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned.
Notice: In cold weather, water can freeze and crack the engine, radiator, heater core and other parts. Use the recommended coolant and the proper coolant mixture. { CAUTION You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough.
5. Start the engine. 6. With the engine idling, top of f the coolant through the radiator pressure cap opening until full. Wait 30 seconds for the coolant to settle and top off, if the level drops. 7. Once the system is full, put the radiator pressure cap back on by turning clockwise.
4. Turn the cap counterclockwise and pull it straight up. 5. When the engine is hot, the level should be at the hot MAX level. When the engine is cold, the fluid level should be between MIN and MAX on the dipstick.
Notice: • When using concentrated washer fluid, follow the manufacturer’s instructions for adding water. • Do not mix water with ready-to-use washer fluid. Water can cause the solution to freeze and damage your washer fluid tank and other parts of the washer system.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT-4 brake fluid. There are only two reasons why the brake fluid level in the reservoir might go down. The first is that the brake fluid goes down to an acceptable level during normal brake lining wear.
Notice: • Using the wrong fluid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced.
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking.
Headlamp Aiming The optical headlamp aiming system has been preset at the factory and should need no further adjustment. However, if the vehicle is damaged adjustment may be necessary. If oncoming vehicles flash their high beams at you, this may also mean the vertical aim needs to be adjusted.
4. At the wall, measure from the ground upward (A) to the recorded distance from Step 3 and mark it. 5. Draw or tape a horizontal line (B) on the wall the width of the vehicle at the height of the mark in Step 4. Notice: Do not cover a headlamp to improve beam cut-off when aiming.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 9-32 . For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs { CAUTION Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
4. For the driver side remove the clip from the air cleaner/filter cover. Move the cover to the back, out of the way. 5. Turn the dust cap counterclockwise to remove. 6. Press the two prongs together on the connector to remove the wiring harness connector.
12. Turn the dust cap clockwise to lock it into place. 13. For the driver side reinstall the air cleaner/filter cover. 14. For the passenger side reinstall the coolant bottle filler neck. 15. Reinstall the radiator support screws. Taillamps A. Turn Signal Lamp B.
9. Push the new bulb into the socket and turn it clockwise to lock it into place. 10. Push the bulb socket straight in and turn it clockwise to lock it into place. 11. Make sure the seals are applied to the taillamp assembly and screws. 12. Raise the spare tire cover.
Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block. An electrical overload will cause the lamps to turn off. If this happens, have your headlamp wiring checked right away. Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse.
Fuses Usage F1 Airbag F2 Trunk Release F3 Door Locks F4 Inadvertent Power LED F5 Courtesy/Turn Signal Lamps/Front Passenger Turn Signal F6 Rear and Side Passenger Side Turn Signal F7 Spare F8 Driver S.
Fuses Usage F15 Outside Rearview Mirrors F16 Sunroof/Automatic Transmission Shift Lock F17 Sunroof F18 Automatic Occupant Sensor F19 Driver Side Heated Seat F20 Passenger Side Heated Seat F21 Daytime .
Fuses Usage FL1 Spare FL2 Rear Defog FL3 ABS Motor FL4 Battery Main 3 FL5 Battery Main 1 FL6 Spare FL7 Battery Main 2 FL8 Starter FL9 HVAC Blower Motor FL10 Fan 1 Engine Cooling (Right) FL11 Spare FL1.
Fuses Usage F10 Driver Side Low-Beam Headlamp F11 Spare F12 Passenger Side Low-Beam Headlamp F13 Spare F14 Spare F15 Front Wiper F16 Spare F17 Theft Horn F18 Spare F19 Passenger Side High-Beam Headlam.
Relays Usage R15 Windshield Wiper R16 Horn R17 Fan 1 (Engine Cooling) R18 Parking Lamps R19 Fan 2 (Engine Cooling) R20 Fan 3 (Engine Cooling) Rear Compartment Fuse Block The rear compartment fuse block is located on the left side of the trunk behind a cover.
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. { CAUTION Poorly maintained and improperly used tires are dangerous.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples show a typical passenger vehicle tire and a compact spare tire sidewall. (A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire’s width, height, aspect ratio, construction type, and service description.
(E) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG) : Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance.
(E) Tire Inflation : The temporary use tire or compact spare tire should be inflated to 60 psi (420 kPa). For more information on tire pressure and inflation see Inflation - Tire Pressure on page 9-46 .
Tire Terminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
GAWR RR : Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 8-28 . Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure.
Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead.
Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right.
Tire Size Recommended Cold Tire Inflation Occupant and Cargo Weight: 573 lbs (260 kg) or Less Occupant and Cargo Weight: Up to 917 lbs (416 kg) (Vehicle Capacity Weight) Front Tires Rear Tires Front .
If you overfill the tire, release air by pushing on the metal stem in the center of the tire valve. Recheck the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.
Tire Size Recommended Cold Tire Inflation Occupant and Cargo Weight: 573 lbs (260 kg) or Less Occupant and Cargo Weight: Up to 917 lbs (416 kg) (Vehicle Capacity Weight) Front Tires Rear Tires Front .
Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.
The TPMS operates on a radio frequency and complies with RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
The vehicle’s TPMS system can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection and Rotation on page 9-54 and Tires on page 9-39 . Notice: Using non-approved tire sealants could damage the Tire Pressure Monitor System (TPMS) sensors.
If the TPMS is not functioning it cannot detect or signal a low tire condition. See the dealer/retailer for service if the TPMS malfunction light and DIC message comes on and stays on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code.
6. The driver side front indicator lamp turns off and the passenger side front indicator lamp comes on to indicate that corner’s sensor is ready to be learned.
Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 9-56 and Wheel Replacement on page 9-61 . When rotating the vehicle’s tires, always use the correct rotation pattern shown here.
When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when the tires have only 1/16 inch (1.
GM’s exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM’s TPC Spec number is molded onto the tire’s sidewall near the tire size.
Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed on your vehicle. Non-TPC Spec rated tires may give a low-pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires.
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A Th.
Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
the alignment might need to be checked. If you notice your vehicle vibrating when driving on a smooth road, the tires and wheels might need to be rebalanced. See your dealer/retailer for proper diagnosis. Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded.
Tire Chains { CAUTION Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash.
A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout, remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go.
Tire Sealant and Compressor Kit (V8 Engine) This vehicle has a tire sealant and compressor kit in place of a jack or spare tire. It is located in a foam container in the trunk. The tire sealant and compressor kit can be used to repair a flat tire by sealing small punctures in the tread of the tire.
Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow these directions closely for correct sealant usage. A. On/Of f Switch B. Air Compressor Accessory Plug C. Air Compressor D. Sealant Canister E. Sealant/Air Hose F.
{ CAUTION Overinflation could cause the tire to rupture, and you or others could be injured. Be sure to read the inflator instructions, and inflate the tire to its recommended pressure. Do not exceed 36 psi (248 kPa). 7. Push the On/Of f switch (A) to the I (on) position.
11. Unplug the air compressor accessory plug (B) from the accessory power outlet in the vehicle. 12. Turn the sealant/air hose (E) counterclockwise to remove. 13. Replace the tire valve stem cap. 14. Stow the sealant/air hose (E) and air compressor accessory plug (B) in their original locations.
19. Wipe of f any sealant from the wheel, tire or vehicle. 20. Dispose of the used sealant canister at a local dealer/retailer or in accordance with local state codes and practices. After using the sealant canister, replace it with a new canister available from your dealer/retailer.
{ CAUTION Idling the engine in a closed-in place or with the climate control system off can cause deadly carbon monoxide (CO). See Engine Exhaust on page 8-12 . 5. Start the vehicle. The vehicle must be running while using the air compressor. { CAUTION Overinflation could cause the tire to rupture, and you or others could be injured.
Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unlock the air-only hose from the sealant canister by pulling up on the lever. 2. Pull the air-only hose from the sealant canister. 3. Unwrap the sealant/air hose from the compressor.
Changing a Flat Tire (V6 Engine) If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. { CAUTION Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Removing the Spare Tire and Tools Spare Tire The equipment you will need is located in the rear storage area. 1. Open the trunk. See Trunk on page 2-10 . 2. Pull the handle of the spare wheel cover strap straight up and secure to the trunk lid. 3. Turn the retainer nut counterclockwise and remove the spare tire.
Tools A. Jack Handle B. Nut Cap Tool C. Wheel Wrench D. Jack 1. Turn the second retainer nut counterclockwise and remove the panel. 2. Remove the tools from the tool container. 3. Place the tools next to the tire being changed. Removing the Flat Tire and Installing the Spare Tire 1.
Notice: Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty. 3. Position the jack lift head at the jack location nearest the flat tire. The location is indicated by a mark on the bottom edge of the vehicle.
The jack handle must be unfolded at a right angle before it is used. 6. Raise the vehicle by turning the jack handle clockwise 180°. 7. Pull the jack handle towards you. 8. Repeat Steps 7 and 8 until the vehicle is far enough off the ground so there is enough room for the compact spare tire to fit under the vehicle.
{ CAUTION Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
14. Tighten the wheel nuts firmly in a crisscross sequence, as shown. { CAUTION Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to a crash. If you have to replace them, be sure to get new original equipment wheel nuts.
Storing a Flat or Spare Tire and Tools { CAUTION Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Compact Spare Tire Although the compact spare tire was fully inflated when the vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated.
Jump Starting If your battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you.
The jump start positive (A) and negative posts (B) are located in the engine compartment on the driver side of the vehicle. These posts are used instead of a direct connection to the battery. The positive jump start connection is covered by a red cap.
Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty.
6. Connect the other end of the red positive (+) cable to the positive (+) terminal of the good battery (B). 7. Connect one end of the black negative (–) cable to the negative (–) terminal of the good battery (C). 8. Connect the other end of the black negative (–) cable to the negative (–) post (D).
Towing Towing Your Vehicle Consult your dealer/retailer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 12-6 . Shift Lock Manual Release The transmission has an electric park lock called a shift lock manual release.
6. Press the select button and move the transmission gear selector to the N (Neutral) position (G). 7. Release the lever (F). 8. After the vehicle has been moved, align the shift lock manual release cover plate (D) and install the retainer (E) so the automatic transmission can operate properly.
Successful, safe trailering takes correct equipment, and it has to be used properly. That is the reason for this part. In it are many time-tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers.
Weight of the Trailer How heavy can a trailer safely be? It should never weigh more than 2,000 lbs (907 kg). But even that can be too heavy. It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much your vehicle is used to pull a trailer are all important.
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inflated to the upper limit for cold tires. You will find these numbers on the Tire-Loading Information label. See Loading the Vehicle on page 8-28 . Then be sure you do not go over the GVW limit for your vehicle, including the weight of the trailer tongue.
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you will want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer.
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle may need a different turn signal flasher and/or extra wiring. Check with your dealer/retailer. The arrows on your instrument panel will flash whenever you signal a turn or lane change.
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • Start your engine. • Shift into a gear. • Release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks.
When cleaning your vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately.
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible.
Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting.
The surface of these wheels is similar to the painted surface of your vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because you could damage the surface. Do not use chrome polish on aluminum wheels.
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.
Vehicle Care/Appearance Materials Description Usage Polishing Cloth Interior and exterior polishing cloth. Tar and Road Oil Remover Removes tar, road oil, and asphalt. Chrome Cleaner and Polish Use on chrome or stainless steel. White Sidewall Tire Cleaner Removes soil and black marks from whitewalls and raised white lettering.
Description Usage Foaming Tire Shine Low Gloss Cleans, shines, and protects tires. No wiping necessary. Wash Wax Concentrate Medium foaming shampoo. Cleans and lightly waxes. Biodegradable and phosphate free. Spot Lifter Quickly removes spots and stains from carpets, vinyl, and cloth upholstery.
Technical Data Vehicle Identification Vehicle Identification Number (VIN) ................. .10-1 Service Parts Identification Label .......... .10-1 Capacities and Specifications Capacities and Specifications ................. .10-2 Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle.
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 11-12 for more information.
Application Capacities English Metric Fuel Tank 19.3 gal 73.0 L Wheel Nut Torque 125 lb ft 170 Y All capacities are approximate. When adding, be sure to fill to the approximate level, as recommended in this manual. Engine Specifications Engine VIN Code Transmission Spark Plug Gap 3.
✍ NOTES 10-4 Technical Data 2008 - Pontiac G8 Owner Manual.
Service and Maintenance Service and Maintenance Introduction ...................... .11-1 Maintenance Requirements ................. .11-2 Your Vehicle and the Environment ................... .11-2 Using the Maintenance Schedule ......................
Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended fluids and lubricants as prescribed in this manual are necessary to keep your vehicle in good working condition. Any damage caused by failure to follow scheduled maintenance might not be covered by warranty.
{ CAUTION Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your dealer/retailer to have a qualified technician do the work.
Scheduled Maintenance When the Service Engine Oil message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km).
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. See Engine Oil on page 9-8 . Reset oil life system. See Engine Oil Life System on page 9-10 . An Emission Control Service. •• Visually check for any leaks or damage.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item.
Additional Required Services (cont’d) Service and Miles (Kilometers) 25,000 (40 000) 50,000 (80 000) 75,000 (120 000) 100,000 (160 000) 125,000 (200 000) 150,000 (240 000) Inspect engine accessory drive belt. An Emission Control Service. See footnote (g).
(e) Make sure the safety belt reminder light and safety belt assemblies are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Have any torn or frayed safety belts replaced.
Owner Checks and Services These owner checks and services should be performed at the intervals specified to help ensure vehicle safety, dependability, and emission control performance. Your dealer/retailer can assist with these checks and services. Be sure any necessary repairs are completed at once.
At Least Once a Year Starter Switch Check { CAUTION When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake.
Parking Brake and Automatic Transmission Park (P) Mechanism Check { CAUTION When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number, or specification can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine Oil Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certified for Gasoline Engines starburst symbol.
Maintenance Replacement Parts Replacement parts identified below by name, part number or specification can be obtained from your dealer/retailer. Part GM Part Numbers ACDelco Part Numbers Engine Air Cleaner/Filter 92066873 — Engine Oil Filter 3.6L V6 25177917 PF2129 6.
Engine Drive Belt Routing (A) Air Conditioning Compressor V6 Engine V8 Engine 11-14 Service and Maintenance 2008 - Pontiac G8 Owner Manual.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 11-2 . Any additional information from Owner Checks and Services on page 11-9 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 11-16 Service and Maintenance 2008 - Pontiac G8 Owner Manual.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed Service and Maintenance 11-17 2008 - Pontiac G8 Owner Manual.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 11-18 Service and Maintenance 2008 - Pontiac G8 Owner Manual.
Customer Information Customer Information Customer Satisfaction Procedure ...................... .12-1 Online Owner Center ....... .12-3 Customer Assistance for Text Telephone (TTY) Users ............................. .12-4 Customer Assistance Off ices .
STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the U.S., call the Pontiac Customer Assistance Center at 1-800-762-2737. In Canada, call General Motors of Canada Customer Communication Centre at 1-800-263-3777 (English) or 1-800-263-7854 (French).
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps One and Two, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program.
My GM Canada (Canada only) My GM Canada is a password-protected section of gmcanada.com where you can save information on GM vehicles, get personalized offers, and use handy tools and forms with greater ease.
Canada — Customer Assistance General Motors of Canada Limited Customer Communication Centre, CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 www.
General Motors of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830. Roadside Assistance Program For vehicles purchased in the U.S., call 1-800-ROADSIDE (762-3743); (Text telephone (TTY): 1-888-889-2438) .
• Jump Start: A battery jump start is covered at no charge if the vehicle does not start. • Trip Routing Service (Canada only): Upon request, Roadside Assistance will send you detailed, computer p.
Calling For Assistance For prompt and eff icient assistance when calling, please provide the following to the Roadside Assistance Representative: • Your name, home address, and home telephone number.
Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada) and extended powertrain warranty in both the U.
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair. Rental reimbursement will be limited and must be supported by original receipts.
Recycled original equipment parts may also be used for repair. These parts are typically removed from vehicles that were total losses in prior crashes.
If a Crash Occurs Here is what to do if you are involved in a crash. • Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. • If there has been an injury, call emergency services for help.
• Choose a reputable collision repair facility for your vehicle. Whether you select a dealer/retailer or a private collision repair facility to fix the damage, make sure you are comfortable with them. Remember, you will have to feel comfortable with their work for a long time.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traff ic Safety Administration (NHTSA) in addition to notifying General Motors.
In Canada, call 1-800-263-3777 (English) or 1-800-263-7854 (French), or write: General Motors of Canada Limited Customer Communication Centre, CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P.
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven.
GM will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an off icial request of police or similar government off ice; as part of GM’s defense of litigation through the discovery process; or, as required by law.
✍ NOTES 12-18 Customer Information 2008 - Pontiac G8 Owner Manual.
A Accessories and Modifications ...................... 9 - 3 Accessory Power Outlets ........ 4 - 9 Adding Equipment to Y our Airbag-Equipped V ehicle . . . . 1-30 Additives, Fuel ..................... 8-34 Add-On Electrical Equipment . .............
Bulb Replacement ................ 9-29 Halogen Bulbs . . . ............... 9-29 Headlamp Aiming . ............. 9-27 Headlamps and Parking Lamps . . ....................... 9-29 Replacement Bulbs ........... 9-32 T aillamps . . .......................
D Daytime Running Lamps ......... 5 - 2 Daytime Running Lamps Indicator Light .................. 4-21 Defensive Driving . . . .............. 8-13 DIC V ehicle Customization . . . . 4-32 Disc, MP3 . . . ........................ 6-19 Doing Y our Own Service Work .
Fog Lamp F o g .................................. 5 - 3 Fog Lamp Light . . . . ............... 4-21 Front Seats . . ......................... 1 - 2 Fuel ................................... 8-32 Additives . . ....................... 8-34 California Fuel .
I Ignition Positions . . . ................ 8 - 2 Immobilizer . ......................... 2-11 Immobilizer Operation ........... 2-12 Infants and Y oung Children, Restraints . . ...................... 1-34 Inflation - T ire Pressure ......... 9-46 Inflator Kit, T ire .
Maintenance Schedule (cont.) Scheduled Maintenance ..... 11-4 Using . ............................. 11-2 Y our V ehicle and the Environment . . . .............. 11-2 Malfunction Indicator Light ..... 4-18 Manual Shift Lock Release ............ 9-84 Manual Seats .
R Radiator Pressure Cap ......... 9-15 Radio Frequency Identification (RFID), Privacy . . . ............ 12-17 Radio(s) . . . . . . . . ....................... 6 - 3 Radios Reception . . ...................... 6-24 Setting the Clock ................ 6 - 2 Theft-Deterrent .
Security Light . . . ................... 4-21 Service . . . . . ........................... 9 - 2 Accessories and Modifications .................. 9 - 3 Adding Equipment to the Outside of the V ehicle ..... 9 - 4 California Perchlorate Materials Requirements .
Tires (cont.) Pressure Monitor Operation ..................... 9-51 Pressure Monitor System . . . 9-49 Removing the Flat T ire ...... 9-73 Removing the Spare T ire and T ools ..................... 9-72 Storing a Flat or Spare T ire and T ools ........
W W arning Lights, Gages and Indicators . . . . . . .................. 4-10 W arnings DIC W arnings and Messages .................... 4-27 Hazard W arning Flashers . . . . 4-4 Wheels Alignment and Tire Balance . . . .................... 9-60 Different Size .
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pontiac G8 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pontiac G8 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pontiac G8, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pontiac G8 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pontiac G8, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pontiac G8.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pontiac G8. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pontiac G8 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
