Manuel d'utilisation / d'entretien du produit 2009 torrent du fabricant Pontiac
Aller à la page of 440
Seats and Restraint System ............................. 1 - 1 Front Seats ............................................... 1 - 2 Rear Seats .............................................. 1-10 Safety Belts ............................................. 1-12 Child Restraints .
GENERAL MOTORS, GM, the GM Emblem, PONTIAC, the PONTIAC Emblem, and the name TORRENT are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. GM reserves the right to make changes after that time without further notice.
Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index.
Front Seats ..................................................... .1-2 Manual Seats ............................................... .1-2 Seat Height Adjuster ...................................... .1-3 Power Seat ......................................
Front Seats Manual Seats { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Seat Height Adjuster To manually raise or lower the seat, move the lever repeatedly upward or downward Power Seat To adjust the seat: • Slide the control forward or rearward to move the seat forward or rearward. • Move the front and rear of the control up or down to raise or lower the front and rear part of the seat cushion.
Manual Lumbar On vehicles with this feature, the knob is located on the front of the driver seat lower cushion on the inboard side. Turn the knob clockwise or counterclockwise to increase or decrease the lumbar support. Heated Seats If your vehicle has heated seats, the switches are located on the instrument panel near the climate controls.
Manual Reclining Seatbacks { CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
{ CAUTION: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even if when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down.
Passenger Folding Seatback { CAUTION: If you fold the seatback forward to carry longer objects, such as skis, be sure any such cargo is not near an airbag. In a crash, an inflating airbag might force that object toward a person. This could cause severe injury or even death.
4. Continue to fold the seat forward until it locks in the folded position. 5. Pull up on the seatback to be sure it is locked. To raise the seatback, do the following: 1. Lift up fully on the recliner lever, located on the outboard side of the seat, and push up on the seatback.
Rear Seats Split Folding Rear Seat The rear split bench seatbacks have three available positions — folded forward, upright, or partially reclined. Both of the seatbacks can be moved to any of the three positions independent of the other seatback position.
To fold the seatback down, do the following: Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. { CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-14.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 1-15.
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces.
Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way. { CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way. { CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Q: What is wrong with this? A: The belt is behind the body. { CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Q: What is wrong with this? A: The belt is twisted across the body. { CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index.
5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants.
Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off the shoulder.
There is one guide for each outside passenger position in the rear seat. Here is how to install a comfort guide to the safety belt: 1. Remove the guide from its storage clip on the back of the seatback. 2. Place the guide over the belt, and insert the two edges of the belt into the slots of the guide.
{ CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. The manufacturer’s instructions that come with the booster seat state the weight and height limitations for that booster.
Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
{ CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.
{ CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types.
{ CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A forward-facing child seat (B) provides restraint for the child’s body with the harness. A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle’s safety belt system. A booster seat can also help a child to see out the window.
Securing an Add-On Child Restraint in the Vehicle { CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We recommend that children and child restraints be secured in.
When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle.
A. Child restraint using LATCH B. Occupant prohibited C. Child restraint or occupant using safety belt A. Child restraint or occupant using safety belt A. Child restraint or occupant using safety belt B. Child restraint using LATCH Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash.
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
The top tether anchors for each rear seating position are located on the back of the rear seatback. You may need to adjust the rear compartment storage panel/cover in the rear cargo area to access the anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
Securing a Child Restraint Designed for the LATCH System { CAUTION: If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed.
{ CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Buckle any unused safety belts behind the child restraint so children cannot reach them.
This system is designed to make installation of child restraints easier. When using lower anchors, do not use the vehicle’s safety belts. Instead use the vehicle’s anchors and child restraint attachments to secure the restraints. Some restraints also use another vehicle anchor to secure a top tether.
If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. If the position you are using has an adjustable headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint.
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle.
4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-44 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
CAUTION: (Continued) Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat.
4. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Airbag System Your vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. Your vehicle may have the following airbags: • A roof-rail airbag for the driver and the passenger seated directly behind the driver.
Here are the most important things to know about the airbag system: { CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ CAUTION: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Where Are the Airbags? The driver’s airbag is in the middle of the steering wheel. The right front passenger’s airbag is in the instrument panel on the passenger’s side.
If your vehicle has roof-rail airbags for the driver, right front passenger, and second row outboard passengers, they are in the ceiling above the side windows. { CAUTION: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inflate if the impact exceeds a predetermined deployment threshold.
In any particular crash, no one can say whether an airbag should have inflated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, inflation is determined by what the vehicle hits, the angle of the impact, and how quickly the vehicle slows down.
What Will You See After an Airbag Inflates? After the frontal airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy.
In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system.
The passenger sensing system works with sensors that are part of the right front passenger seat. The sensors are designed to detect the presence of a properly-seated occupant and determine if the right front passenger frontal airbag should be enabled (may inflate) or not.
If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, we recommend that rear-facing child restraints not be transported in your vehicle, even if the airbag is off.
{ CAUTION: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. To help avoid injury to yourself or others, have the vehicle serviced right away. See Airbag Readiness Light on page 3-28 for more information, including important safety information.
If the Of f Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat.
Additional Factors Af fecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status.
Adding Equipment to Your Airbag-Equipped Vehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash.
Keys .............................................................. .2-2 Remote Keyless Entry (RKE) System ............... .2-3 Remote Keyless Entry (RKE) System Operation .................................................. .2-4 Remote Vehicle Start ..
Keys { CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
Remote Keyless Entry (RKE) System If this vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules.
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-3 .
Press and hold L for more than two seconds to activate the panic alarm. The turn signal lamps flash and the horn sounds repeatedly for 30 seconds. The alarm turns off when the ignition is moved to ON/RUN or L is pressed again. The ignition must be in LOCK/OFF for the panic alarm to work.
Remote Vehicle Start Your vehicle may have the remote start feature. This feature allows you to start the engine from outside the vehicle. See “REMOTE START” under DIC Vehicle Personalization on page 3-59 for instructions on how to enable and disable this feature.
3. To extend the engine run time by 10 minutes, repeat Steps 1 and 2 while the engine is still running. The engine run time can only be extended if it is the first remote start since the vehicle has been driven. Remote start can be extended one time.
The remote vehicle start feature will not operate if any of the following occur: • The vehicle’s key is in the ignition. • The vehicle’s hood, liftgate or doors are not closed. • The hazard warning flashers are on. • There is an emission control system malfunction.
Doors and Locks Door Locks { CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Programmable Automatic Door Locks Your vehicle has an automatic lock/unlock feature which enables you to program the power door locks through the Driver Information Center (DIC). See DIC Vehicle Personalization on page 3-59 for more information on DIC programming.
Lockout Protection If you press the power door lock switch when the key is in the ignition and any door is open, all the doors will lock and only the driver’s door will unlock.
Liftgate Operation with Loss of Power The liftgate is equipped with an electric latch. If the battery is disconnected or has low voltage, the liftgate will not open. To open the liftgate if this happens, remove the interior trim plug located at the base of the liftgate from inside the vehicle.
Windows { CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
Express-Down Window The driver’s window switch has an express-down feature that allows the window to be lowered without holding the switch. Press the bottom of the switch part way, and the driver’s window will open a small amount. Press the switch down all the way down and release it and the window will go down automatically.
Content Theft-Deterrent Your vehicle has a content theft-deterrent alarm system. To activate the theft-deterrent system: 1. Open the door. 2. Lock the door with the power door lock switch or the Remote Keyless Entry (RKE) transmitter. If you are using the RKE transmitter, the door does not need to be open.
PASS-Key ® III+ Electronic Immobilizer Operation Your vehicle has PASS-Key ® III+ (Personalized Automotive Security System) theft-deterrent system. PASS-Key ® III+ is a passive theft-deterrent system. The system is automatically armed when the key is removed from the ignition.
See your dealer/retailer or a locksmith who can service PASS-Key ® III+ to get a new key blank that is cut exactly as the ignition key that operates the system. To program the new additional key: 1. Verify that the new key has a 1 stamped on it. 2. Insert the original, already programmed, key in the ignition and start the engine.
Ignition Positions The ignition switch has four different positions. In order to shift out of P (Park), ignition must be in the ON/RUN or ACC/ACCESSORY and the regular brake pedal must be applied. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key.
Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine is turned off: • Audio System • Power Windows • Sunroof (if equipped) Power to these accessories will continue to operate for up to 10 minutes or until the driver door is opened.
2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or − 18°C), it could be flooded with too much gasoline. Try pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in START for up to a maximum of 15 seconds.
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located on the passenger side of the engine compartment, near the radiator. 3. Plug it into a normal, grounded 110-volt AC outlet. { CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock.
{ CAUTION: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly.
N (Neutral): In this position, the engine does not connect with the wheels. To restart the engine when the vehicle is already moving, use N (Neutral) only. { CAUTION: Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is firmly on the brake pedal, the vehicle could move very rapidly.
Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will not be covered by the vehicle warranty. If you are stuck, do not spin the tires. When stopping on a hill, use the brakes to hold the vehicle in place.
P (Park): This position locks the front wheels. It is the best position to use when the engine is started because the vehicle cannot move easily. { CAUTION: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set.
{ CAUTION: Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is firmly on the brake pedal, the vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while the engine is running at high speed.
MSM (Manual Shift Mode) To use this feature, do the following: 1. Move the shift lever from D (Drive) to the left into the manual gate. While driving in manual shift mode, the transmission will remain in the driver gear selected. When coming to a stop in the manual position, the vehicle will automatically shift to 1 (First) gear.
Transmission Overheating If the transmission fluid temperature rises above 270°F (132°C) or rises rapidly, the Engine Coolant Temperature Warning Light will flash.
Parking Brake The parking brake lever is located to the right of the driver seat. To set the parking brake, hold the brake pedal down and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on. To release the parking brake, hold the brake pedal down.
Shifting Into Park { CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured.
Torque Lock If you are parking on a hill and you do not shift the transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it diff icult to pull the shift lever out of P (Park).
Parking Over Things That Burn { CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to reduce the glare of headlamps from behind you. Push the tab forward for daytime use and pull it for nighttime use.
Outside Convex Mirrors { CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.
OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature. Some services such as Remote Door Unlock or Stolen Vehicle Location Assistance may not be available until the owner of the vehicle registers with OnStar.
OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days.
How OnStar Service Works The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar Call Center when the OnStar button is pressed, the emergency button is pressed, or if the airbags or AACN system deploy.
Storage Areas Glove Box To open the glove box, pull the handle to the left and pull the glove box door down until it stops and is fully open. Cupholders Cupholders are located on the lower front of the center console. Pull-out cupholders are located at the bottom of the armrest and on the back of the rear seat center console.
The roof rack crossrails lock along the straight section of the side rail. Press the levers down until the locking mechanisms fully engage to the side rail. Make sure each lever is in the down position. The crossrail will not slide when properly engaged.
Rear Compartment Storage Panel/Cover Your vehicle may have an adjustable panel/cargo cover feature. The panel/cargo cover can be adjusted into three positions. There is a flip panel towards the front of the cargo cover. You may have to flip this panel upward in order to gain access to the cargo cover.
{ CAUTION: If you were to carry things on the adjustable panel when it is in the upper (cargo cover) or center positions, during a sudden vehicle movement or a crash, those things could be thrown around in the vehicle.
Table Your vehicle may have an adjustable panel that also functions as a table. The maximum load for the table is 100 lbs. distributed (45 kg). To set up the table, do the following: 1. With the adjustable panel in the upper position, pull it rearward to position it for use as a table.
Sunroof If the vehicle is equipped with a sunroof, the controls to operate it are located on the headliner above the rearview mirror. The ignition must be in RUN/ON or ACC/ACCESSORY, or Retained Accessory Power (RAP) must be active, to operate the sunroof.
✍ NOTES 2-46.
Instrument Panel Overview .............................. .3-4 Hazard Warning Flashers ............................... .3-6 H o r n ............................................................ .3-6 Tilt Wheel ...........................................
Highbeam On Light ...................................... .3-39 Service All-Wheel Drive Light ........................ .3-40 All-Wheel Drive Disabled Light ....................... .3-40 Gate Ajar Light ............................................ .3-41 Door Ajar Light .
✍ NOTES 3-3.
Instrument Panel Overview 3-4.
The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-23 . B. Turn Signal/Multifunction Lever on page 3-7 . C. Instrument Panel Cluster on page 3-25 . D. Windshield Wipers on page 3-8 . E. DIC Operation and Displays on page 3-43 .
Hazard Warning Flashers | (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press | again to turn the flashers off.
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : Turn and Lane-Change Signals 53 : Headlamp High/Low-Beam Changer O : Exterior Lamp Control Flash-to-Pass. Information for these features is on the pages following.
Headlamp High/Low-Beam Changer To change the headlamps from low beam to high, push the turn signal lever away from you. To change from high beam to low beam, pull the turn signal lever towards you. To flash the high beams from low beam, pull the turn signal lever all the way towards you.
9 (Off): Turns of f the windshield wipers. 8 (Mist): Move the lever all the way down to mist and release for a single wiping cycle. The windshield wipers stop after one wipe and the lever returns to its starting position. Hold the lever on mist longer for more wipes.
Rear Window Wiper/Washer The rear wiper and rear wash buttons are located on the instrument panel above the audio system. Z (Rear Wiper): Press to turn the rear wiper on and off. When the wiper is on it runs intermittently at a preset speed. Y (Wash): Press to spray washer fluid on the rear window.
Setting Cruise Control { CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Resuming a Set Speed If the cruise control is at a set speed and the brakes are applied, this disengages the cruise control. The instrument panel cluster light J also goes out, indicating cruise is no longer engaged. To return to the previously set speed, it does not need to be reset.
Ending Cruise Control There are three ways to end the cruise control: • Step lightly on the brake pedal. • Press the I button, to turn off the cruise control system. • Press the [ button. When cruise control disengages, the cruise symbol in the instrument panel cluster goes out.
Headlamps on Reminder If you open the driver’s door with the ignition off and the lamps on, you will hear a warning chime. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day.
Fog Lamps Use the fog lamps for better visibility in foggy or misty conditions. The fog lamps button is located on the instrument panel above the radio. The parking lamps or low-beam headlamps must be on to use the fog lamps. # : Press to turn the fog lamps on or off.
Dome Lamp For vehicles with a dome lamp, move the lever to change the setting. 9 (Off): Turns the lamp of f, even when a door is open. 1 (Door): The lamp comes on automatically when a door is opened.
Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly bring the charge back up.
Accessory Power Outlet(s) The accessory power outlets can be used to connect electrical equipment, such as a cellular phone. The two accessory power outlets are located in the front and at the rear of the center console storage area. To use the outlets, remove the cover.
Climate Controls Climate Control System The heating, cooling, and ventilation for the vehicle can be controlled with this system. For vehicles with the remote start feature, the climate control system functions as part of the remote start feature. See Remote Keyless Entry (RKE) System Operation on page 2-4 .
6 (Floor): Air is directed to the floor outlets with some air directed to the windshield. When this mode is selected, the system turns the recirculation mode off. Recirculation mode cannot be selected while in floor mode. This helps to prevent window fogging.
Using these settings together for long periods of time may cause the air inside of the vehicle to become too dry. To prevent this from happening, after the air inside of the vehicle has cooled, turn the recirculation mode off.
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. The rear window defogger only works when the ignition is in ON/RUN. < (Rear Window Defogger): Press to turn the rear window defogger on or off. An indicator light comes on to show that the rear window defogger is on.
Outlet Adjustment Use the louvers located on the air outlets to change the direction of the airflow. Operation Tips • Clear away any ice, snow, or leaves from the air inlets at the base of the vehicle that may block the flow of air into the vehicle.
4. Remove the air inlet panel to access the filter. 5. Press the release tab on the driver’s side of the filter and pull out the edge of the filter. 6. Remove the filter from the vehicle. 7. Install a new passenger compartment air filter. For the type of filter to use see Maintenance Replacement Parts on page 6-13 .
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, how much fuel you are using, and many other things you will need to drive safely and economically.
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada).
Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then flashes for several more.
Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions.
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-66 for important safety information.
Charging System Light If this light comes on while you are driving, you may have a problem with the charging system. A charging system Driver Information Center (DIC) message may also appear. See DIC Warnings and Messages on page 3-50 for more information.
When the ignition is on, the brake light will come on when you set your parking brake. The light will stay on if your parking brake does not release fully. A chime will also sound if the parking brake is not fully released and the vehicle is moving. If it stays on after your parking brake is fully released, it means you have a brake problem.
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off.
Engine Coolant Temperature Warning Light The engine coolant temperature warning light will come on when the engine has overheated. If this happens you should pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-29 for more information.
Tire Pressure Light For vehicles with a tire pressure light, this light comes on briefly when the engine is started and provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated.
This light should come on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer. If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required.
If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer/retailer for service as soon as possible.
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration.
If the light comes on and stays on, it means that oil is not flowing through the engine properly. The vehicle could be low on oil and it might have some other system problem. Change Engine Oil Light If this light comes on and stays on for 30 seconds, it means that service is required for your vehicle.
Cruise Control Light The cruise control light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 3-10 for more information. Reduced Engine Power Light Your vehicle has a reduced engine power light.
Service All-Wheel Drive Light This light is located in the center of your instrument panel cluster. This light and the SERVICE ALL WHEEL DRIVE message in the Driver Information Center (DIC) will come on and stay on to indicate that there may be a problem with the drive system and service is required.
Gate Ajar Light If this light comes on, your liftgate is not completely closed. Driving with the liftgate open can cause carbon monoxide (CO) to enter the vehicle. See Engine Exhaust on page 2-33 for more information. Door Ajar Light This light will come on when a door is open.
Here are four things that some owners ask about. None of these show a problem with your fuel gage: • At the service station, the fuel pump shuts off before the gage reads full. • It takes a little more or less fuel to fill up than the gage indicated.
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages will appear in the DIC display located in the center of the instrument panel cluster. The DIC buttons are located on the center of the instrument panel. The DIC comes on when the ignition is on.
T (Vehicle Information): Press this button to scroll through the vehicle information displays and to personalize the feature settings on your vehicle. See “Vehicle Information Menu Items” following and DIC Vehicle Personalization on page 3-59 for more information on these displays.
RANGE Press the trip/fuel button until RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling. The fuel range estimate is based on an average of the vehicle’s fuel economy over recent driving history and the amount of fuel remaining in the fuel tank.
Remember, you must reset the OIL LIFE yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change.
LEARN REMOTE KEY This display allows you to match Remote Keyless Entry (RKE) transmitters to your vehicle. To match an RKE transmitter to your vehicle: 1. Make sure the vehicle is in P (Park). 2. Press the vehicle information button until LEARN REMOTE KEY PRESS V TO BEGIN displays.
DIC Compass Your vehicle may have a compass in the Driver Information Center (DIC). Compass Zone The zone is set to zone eight upon leaving the factory.
Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible.
DIC Warnings and Messages Messages are displayed on the DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition.
BATTERY SAVER ACTIVE This message displays when the charging system detects that the battery is being drained. You may notice that the vehicle attempts to reduce the drain for you by turning off accessories, such as interior fans, rear defogger, and heated seats.
CHECK TIRE PRESSURE This message displays when the pressure in one or more of the vehicle’s tires needs to be checked. This message also displays LEFT FRONT, RIGHT FRNT (Front), LEFT REAR, or RIGHT REAR to indicate which tire needs to be checked. You can receive more than one tire pressure message at a time.
ENGINE OVRHEATD (Overheated) STOP ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible.
OIL PRSSURE (Pressure) LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the Driver Information Center (DIC), stop the vehicle as soon as possible.
SERVICE ALL WHEEL DRIVE If your vehicle has the All-Wheel Drive (AWD) system, this message displays along with the service all-wheel drive light if a problem occurs with this system. See Service All-Wheel Drive Light on page 3-40 . If this message appears, stop as soon as possible and turn off the vehicle.
SERVICE STABILITRAK This message displays if there has been a problem detected with the StabiliTrak ® System. A warning light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-32 . See StabiliTrak ® System on page 4-6 for more information.
SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer/retailer as soon as possible.
THEFT ATTEMPTED This message displays if the content theft-deterrent system has detected a break-in attempt while you were away from your vehicle. See Content Theft-Deterrent on page 2-16 for more information. TIRE LEARNING ACTIVE This message displays when the Tire Pressure Monitor System (TPMS) is re-learning the tire positions on your vehicle.
DIC Vehicle Personalization Your vehicle has personalization capabilities that allow you to program certain features to one preferred setting. All of the personalization options may not be available on your vehicle. Only the options available will be displayed on the DIC.
DISPLAY LANG. (Language) This feature allows you to select the language in which the DIC messages will appear. Press the vehicle information button until DISPLAY LANG. (Language) appears on the DIC display. Press the set/reset button to access the settings for this feature.
AUTO UNLOCK This feature allows you to select whether or not to turn off the automatic door unlocking feature. It also allows you to select which doors and when the doors will automatically unlock. See Programmable Automatic Door Locks on page 2-10 for more information.
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. REMOTE UNLOCK This feature allows you to select the type of feedback you will receive when unlocking the vehicle with the RKE transmitter.
EXIT LIGHTNG (Lighting) This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the vehicle information button until EXIT LIGHTNG (Lighting) appears on the DIC display.
CHIME VOLUME This feature allows you to select the volume level of the chime. Press the vehicle information button until CHIME VOLUME appears on the DIC display.
FACTORY SETTNGS (Settings) This feature allows you to set all of the personalization features back to their factory default settings. Press the vehicle information button until FACTORY SETTNGS (Settings) appears on the DIC display. Press the set/reset button to access the settings for this feature.
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
3. While either the hour or the minutes are flashing, do one of the following to increase or decrease the time: • Press ¨ SEEK or © SEEK. • Press FWD or s REV.
MP3 Radio with a Six-Disc CD Player If the vehicle has a radio with a six-disc CD player, the radio has a MENU button to set the time and date. To set the time and date: 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN, then press O , to turn the radio on.
Radio(s) The vehicle has one of these radios as its audio system. If the vehicle has a Rear Seat Entertainment (RSE) system, it has a CD/DVD radio. See Rear Seat Entertainment (RSE) System on page 3-110 for more information on the vehicle’s RSE system.
The DVD player is the top slot on the radio faceplate. The player can read the DTS programmed DVD Audio or DVD Video media (DTS and DTS 2.0 are trademarks of Digital Theater Systems Inc.). Dolby is manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Finding a Station BAND: Press to switch between AM, FM, or XM (if equipped). The selection displays. f (Tune): Turn to select radio stations. © SEEK ¨ : Press the arrows to go to the previous or to the next station and stay there. To scan stations, press and hold either arrow for a few seconds until a beep sounds.
Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is parked. Tune to favorite stations using the presets, favorites button, and steering wheel controls, if the vehicle has them. See Defensive Driving on page 4-2 .
Setting the Tone (Bass/Treble) (Base Radio with CD) EQ (Equalization): To adjust the bass or treble, press the f knob or EQ button until the desired tone control tab displays. Turn the f knob clockwise or counterclockwise to increase or decrease the setting.
Adjusting the Speakers (Balance/Fade) (Base Radio with CD) ` BAL/FADE (Balance/Fade): To adjust the balance or fade, press the ` button or the f knob until the desired speaker control tab displays. Turn the f knob clockwise or counterclockwise to adjust the setting.
Undesired XM categories can be removed through the setup menu. To remove an undesired category, perform the following: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the XM CAT tab. 3. Turn the f knob to display the category to be removed.
Playing a CD(s) (Six-Disc CD Player) LOAD ^ : Press to load CDs into the CD player. This CD player holds up to six CDs. To insert one CD, do the following: 1. Press and release the ^ button. 2. Wait for the message to insert the disc. 3. Load a CD. Insert the CD partway into the slot, label side up.
Care of the CD and DVD Player Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen.
RDM (Random) (Base Radio with CD): With the random setting, CD tracks can be listened to in random, rather than sequential order. To use random, do the following: 1. Press to play tracks from the CD in random order. The random icon displays. 2. Press again to turn off random play.
Playing a CD (In Either the DVD or CD Slot) Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing (loading a disc into the system, depending on media type and format ranges from 5 to 20 seconds for a CD, and up to 30 seconds for a DVD to begin playing).
s REV (Fast Reverse): Press and hold to reverse playback quickly within a track. Sound is heard at a reduced volume. Release to resume playing the track. The elapsed time of the track displays. FWD (Fast Forward): Press and hold to advance playback quickly within a track.
Audio Output Only one audio source can be heard through the speakers at one time. An audio source is defined as DVD slot, CD slot, XM, FM/AM, Front Aux Jack, or Rear Aux Jack. Press the O button to turn the radio on. The radio can be heard through all of the vehicle speakers.
Using the DVD Player The DVD player is controlled by the buttons on the remote control, by the RSA system, or by the buttons on the radio faceplate. See “Remote Control” under Rear Seat Entertainment (RSE) System on page 3-110 for more information.
O (Power): Press to turn the radio on or off. Turn clockwise or counterclockwise to increase or decrease the volume. Press and hold for more than two seconds turns off the entire radio and Rear Seat E.
DVD-V (Video) Display Buttons Once a DVD-V is inserted, the radio display menu shows several tag options for DVD playing. Press the pushbuttons located under any desired tag option during DVD playback. See the tag options listed below for more information.
DVD-A (Audio) Display Buttons Once a DVD-A is inserted, a radio display menu shows several tag options for DVD playing. Press the pushbuttons located under any desired tag option during DVD playback. See the tag options listed below for more information.
Stopping and Resuming Playback To stop playing a DVD without turning off the system, press the c button on the remote control, or press the pushbutton located under the stop or the play/pause symbol tags displayed on the radio. If the radio head is sourced to something other than DVD-V, press the DVD/CD AUX button to make DVD-V the active source.
Using the Auxiliary Input Jack The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug the headphone set into the front auxiliary input jack. An external audio device such as an iPod, laptop computer, MP3 player, CD changer, etc.
Using an MP3 (Radio with CD or Six-Disc CD Player) MP3/WMA CD-R or CD-RW Disc The radio plays MP3 and WMA files that were recorded on a CD-R or CD-RW disc.
• Minimize the length of the file, folder, or playlist names. Long file, folder, or playlist names, or a combination of a large number of files and folders, or playlists can cause the player to be unable to play up to the maximum number of files, folders, playlists, or sessions.
Order of Play Tracks recorded to the CD-R or CD-RW are played in the following order: • Play begins from the first track in the first playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the first track of the first playlist.
Z EJECT: Press to eject CD-R(s) or CD-RW(s). To eject the CD-R or CD-RW that is currently playing, press and release this button. A beep sounds and Ejecting Disc displays. Once the disc is ejected, Remove Disc displays. The CD-R or CD-RW can be removed.
h (Music Navigator): Use the music navigator feature to play MP3 files on the CD-R or CD-RW in order by artist or album. Press the pushbutton located below the music navigator tab. The player scans the disc to sort the files by artist and album ID3 tag information.
Using an MP3 (Radio with CD and DVD Player) MP3/WMA CD-R or CD-RW Disc Compressed Audio or Mixed Mode Discs The radio also plays discs that contain both uncompressed CD audio (.CDA files) and MP3/WMA files depending on which slot the disc is loaded into.
Root Directory The root directory of the CD-R or CD-RW is treated as a folder. If the root directory has compressed audio files, the directory is displayed as F1 ROOT. All files contained directly under the root directory are accessed prior to any root directory folders.
Preprogrammed Playlists Preprogrammed playlists that were created using WinAmp™, MusicMatch™, or Real Jukebox™ software can be accessed, however, they cannot be edited using the radio. These playlists are treated as special folders containing compressed audio song files.
© SEEK ¨ : Press the left SEEK arrow to go to the start of the current MP3/WMA file, if more than five seconds have played. If less than five seconds have played, the previous MP3/WMA file plays. Press the right SEEK arrow to go to the next MP3/WMA file.
Once the disc has been scanned, the player defaults to playing MP3/WMA files in order by artist. The current artist playing is shown on the second line of the display between the arrows. To listen to MP3/WMA files by another artist, press the pushbutton located below either arrow tab.
XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required.
Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer. Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer.
Bluetooth Controls Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Audio Steering Wheel Controls on page 3-119 for more information. b g (Push To Talk): Press to answer incoming calls, to confirm system information, and to start speech recognition.
4. Start the Pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturers user guide for information on this process.
Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve ph.
3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number.
3. Say the name tag to be deleted. The system responds with “Would you like to delete, <name tag>? Please say yes or no”. • If the name tag is correct, say “Yes” to delete the name tag. The system responds with “OK, deleting <name tag>, returning to the main menu.
Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Digit Dial”. The system responds with “Digit dial using <phone name>, please say the first digit to dial” followed by a tone.
Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. • Press b g and begin speaking to answer the call. • Press c x to ignore a call. Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work.
Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. To Mute a call 1. Press b g . The system responds with “Ready” followed by a tone. 2. Say “Mute Call”.
Voice Pass-Thru Voice Pass-Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone.
3. Say the name tag to send. • If the system clearly recognizes the name tag it responds with “OK, Sending <name tag>” and the dial tones are sent and the call continues. • If the system is not sure it recognized the name tag properly, it responds “Dial <name tag>, Please say yes or no?” followed by a tone.
Rear Seat Entertainment (RSE) System The vehicle may have a DVD Rear Seat Entertainment (RSE) system. The RSE system works with the vehicle’s audio system. The DVD player is part of the front radio. The RSE system includes a radio with a DVD player, a video display screen, audio/video jacks, two wireless headphones, and a remote control.
The infrared transmitters are located in the display below the video screen. The headphones shut off automatically to save the battery power if the RSE system and RSA are shut off or if the headphones are out of range of the transmitters for more than three minutes.
Audio/Video (A/V) Jacks The A/V jacks are located on the rear of the floor console. The A/V jacks allow audio or video signals to be connected from an auxiliary device such as a camcorder or a video game unit to the RSE system. Adapter connectors or cables might be required to connect the auxiliary device to the A/V jacks.
Audio Output Audio from the DVD player or auxiliary inputs may be heard through the following possible sources: • Wireless Headphones • Vehicle Speakers • Vehicle wired headphone jacks on the rear seat audio system, if the vehicle has this feature.
Remote Control To use the remote control, aim it at the transmitter window at the rear of the RSE overhead console and press the desired button. Direct sunlight or very bright light can affect the ability of the RSE transmitter to receive signals from the remote control.
y (Main Menu): Press this button to access the DVD menu. The DVD menu is different on every DVD. Use the navigation arrows to move the cursor around the DVD menu. After making a selection press the enter button. This button only operates when using a DVD.
r (Fast Reverse): Press this button to fast reverse the DVD or CD. To stop fast reversing a DVD video, press the play/pause button. To stop fast reversing a DVD audio or CD, release the fast reverse button. This button might not work when the DVD is playing the copyright information or the previews.
Battery Replacement To change the remote control batteries, do the following: 1. Slide the rear cover back on the remote control. 2. Replace the two batteries in the compartment. Make sure that they are installed correctly, using the diagram on the inside of the battery compartment.
Problem Recommended Action Sometimes the wireless headphone audio cuts out or buzzes. Check for obstructions, low batteries, reception range, and interference from cellular telephone towers or by using a cellular telephone in the vehicle. Check that the headphones are on correctly using the L (left) and R (right) on the headphones.
DVD Distortion Video distortion may occur when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It may be necessary to turn off the DVD player when operating one of these devices in or near the vehicle.
x c (Previous / Phone On Hook): Press to go to the previous radio station stored as a favorite, the previous track if a CD/DVD is playing, to reject an incoming call, or end a current call. b g (Push to Talk / Mute): Press to silence the vehicle speakers only.
XM™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out.
✍ NOTES 3-122.
Your Driving, the Road, and the Vehicle ........... .4-2 Driving for Better Fuel Economy ...................... .4-2 Defensive Driving .......................................... .4-2 Drunk Driving ................................................ .4-3 Control of a Vehicle .
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops.
Drunk Driving { CAUTION: Drinking and then driving is very dangerous. Your reflexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking.
Braking See Brake System Warning Light on page 3-30 . Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second.
Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that will help prevent a braking skid.
Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. Brake Assist This vehicle has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions.
The system may be heard or felt while it is working. This is normal. This light may also come on after extended heavy braking, indicating the brakes have become too hot to limit wheel spin. StabiliTrak can be turned off using the StabiliTrak/ TCS control button.
TCS automatically comes on whenever the vehicle is started. To limit wheel spin, especially in slippery road conditions, the system should always be left on. But TCS can be turned off if needed. The system should be turned off if the vehicle ever gets stuck in sand, mud, ice, or snow and rocking the vehicle is required.
All-Wheel Drive (AWD) System If the vehicle has all-wheel drive (AWD), the AWD system operates automatically without any action required by the driver. If the front drive wheels begin to slip, the rear wheels will automatically begin to drive the vehicle as required.
Steering Electric Power Steering (3.4L V6 Engine) If the engine stalls while driving, the power steering assist system will continue to operate until you are able to stop the vehicle. If power steering assist is lost because the electric power steering system is not functioning, the vehicle can be steered but it will take more effort.
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Of f-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive.
Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle’s tires so they actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all fluid levels and brakes, tires, cooling system, and transmission.
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction.
Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 7-7 . To get help and keep everyone in the vehicle safe: • Turn on the Hazard Warning Flashers on page 3-6 .
Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed.
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible.
Tire and Loading Information Label A vehicle specific Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will find the label attached below the door lock post (striker).
Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Item Description Total A Maximum Vehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 7.
Item Description Total A Maximum Vehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg).
The Certification/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Towing Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/ retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 7-7 .
Dinghy Towing (Vehicles with a 5-speed Transmission) Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components. Do not tow an all-wheel-drive vehicle with any of its wheels on the ground.
If the vehicle is all-wheel-drive, it can be dinghy towed from the front. These vehicles can also be towed by placing them on a platform trailer with all four wheels off of the ground.
Dolly Towing (Front-Wheel-Drive Vehicles with a 5-speed Transmission) To dolly tow a front-wheel drive vehicle with a 5–speed transmission from the front with two of its wheels on the ground: 1. Attach the dolly to the tow vehicle following the dolly manufacturer’s instructions.
Dolly Towing (All-Wheel-Drive Vehicles with a 5-speed Transmission) Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components. Do not tow an all-wheel-drive vehicle with any of its wheels on the ground.
3. Shift the transmission to P (Park). 4. Firmly set the parking brake. 5. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 6. Secure the vehicle to the dolly following the manufacturer’s instructions.
Towing the Vehicle From the Rear Notice: Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the warranty. Never have the vehicle towed from the rear.
Towing a Trailer { CAUTION: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well — or even at all. The driver and passengers could be seriously injured.
Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why the right hitch is needed. • The rear bumper on the vehicle is not intended for hitches. Do not attach rental hitches or other bumper-type hitches to it.
Driving with a Trailer { CAUTION: When towing a trailer, exhaust gases may collect at the rear of the vehicle and enter if the liftgate, trunk/hatch, or rear-most window is open. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled.
Electronic Trailer Sway Control Electronic Trailer Sway Control is integrated into the StabiliTrak system of the vehicle. This feature detects the occurrence of trailer sway that may be caused by improper trailer weight balance, or excessive vehicle speed.
Turn Signals When Towing a Trailer The arrows on the instrument panel flash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps also flash, telling other drivers the vehicle is turning, changing lanes or stopping.
Parking on Hills { CAUTION: Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.
Service ........................................................... .5-3 Accessories and Modifications ......................... .5-3 California Proposition 65 Warning .................... .5-4 California Perchlorate Materials Requirements .... .5-4 Doing Your Own Service Work .
Tires ............................................................. .5-51 Tire Sidewall Labeling .................................. .5-52 Tire Terminology and Definitions .................... .5-56 Inflation - Tire Pressure .........................
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories an.
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
If doing some of your own service work, use the proper service manual. It tells you much more about how to service the vehicle than this manual can. To order the proper service manual, see Service Publications Ordering Information on page 7-16 . This vehicle has an airbag system.
Gasoline Octane If the vehicle has the 3.4L V6 engine (VIN Code F), use regular unleaded gasoline with a posted octane rating of 87 or higher. If the octane rating is less than 87, you might notice an audible knocking noise when you drive, commonly referred to as spark knock.
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel.
Filling the Tank { CAUTION: Fuel vapor burns violently and a fuel fire can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling. Do not smoke if you are near fuel or refueling the vehicle.
{ CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { CAUTION: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs. To help avoid injury to you and others: • Dispense fuel only into approved containers.
Hood Release To open the hood, do the following: 1. Pull the handle with this symbol on it. It is located inside the vehicle, to the left of the brake pedal. 2. Then go to the front of the vehicle and move the secondary hood release lever to the right.
Engine Compartment Overview When you open the hood on the 3.4L V6, here is what you will see: 5-12.
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-20 . B. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-15 . C. Engine Oil Dipstick. See “Checking Engine Oil” under Engine Oil on page 5-15 . D.
When you open the hood on the 3.6L V6, here is what you will see: 5-14.
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-20 . B. Power Steering Fluid Reservoir (Out of View). See Power Steering Fluid on page 5-31 . C. Engine Oil Fill Cap (Out of View). See “When to Add Engine Oil” under Engine Oil on page 5-15 .
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Specifications on page 5-103 .
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Cold Temperature Operation If in an area of extreme cold, where the temperature falls below − 20°F ( − 29°C), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil. Both provide easier cold starting for the engine at extremely low temperatures.
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required.
Engine Air Cleaner/Filter The engine air cleaner/filter is located in the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location.
4. Remove the air outlet duct. 5. Undo the clamps on the filter cover. To remove the cover, pull up on the front and then pull the cover out. 6. Inspect or replace the engine air cleaner/filter. Wipe all dust from inside of the housing and inspect the air cleaner and air outlet duct for cracks, cuts, and deterioration.
Automatic Transmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take your vehicle to the dealer/retailer and have it repaired as soon as possible.
{ CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. { CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
What to Use { CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture.
Notice: If an improper coolant mixture is used, the engine could overheat and be badly damaged. The repair cost would not be covered by the vehicle warranty. Too much water in the mixture can freeze and crack the engine, radiator, heater core, and other parts.
How to Add Coolant to the Surge Tank { CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a specific coolant fill procedure.
If coolant is needed, add the proper DEX-COOL ® coolant mixture at the coolant surge tank. 1. You can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot.
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. By this time, the coolant level inside the coolant surge tank may be lower.
Engine Overheating The vehicle has several indicators to warn of engine overheating. You will find a coolant temperature gage on your vehicle’s instrument panel. See Engine Coolant Temperature Gage on page 3-33 . There are also several different types of engine overheating messages that may be displayed in the Driver Information Center (DIC).
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: • Climbs a long hill on a hot day.
Power Steering Fluid See Engine Compartment Overview on page 5-12 for reservoir location. When to Check Power Steering Fluid Power steering fluid is used in all vehicles with the 3.6L V6 engine. Vehicles with the 3.4L V6 engine have electric power steering and do not use power steering fluid.
Windshield Washer Fluid What to Use When you need windshield or rear window washer fluid be sure to read the instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has suff icient protection against freezing.
Brakes Brake Fluid The brake master cylinder reservoir is filled with DOT-3 brake fluid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake fluid level in the reservoir might go down: • The brake fluid level goes down because of normal brake lining wear.
What to Add Use only new DOT-3 brake fluid from a sealed container. See Recommended Fluids and Lubricants on page 6-11 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly.
When parts of the braking system are replaced — for example, when the brake linings wear down and new ones are installed — be sure to get new approved replacement parts.
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. { CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you.
Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3. Turn off the ignition on both vehicles.
The remote negative ( − ) terminal is located in the front of the engine compartment, near the engine oil dipstick. See Engine Compartment Overview on page 5-12 for more information on the location of the remote positive (+) terminal and the engine oil dipstick.
{ CAUTION: An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. { CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded.
6. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged, too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one.
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
How to Check Lubricant A. Fill Plug B. Drain Plug To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, you’ll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the filler plug hole, located on the transfer case.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 6-11 . Carrier Assembly-Dif ferential (Rear Drive Module) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it.
What to Use Refer to the Maintenance Schedule to determine what kind of lubricant to use. See Recommended Fluids and Lubricants on page 6-11 . Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However, if your vehicle is damaged in a crash, the headlamp aim may be affected.
Headlamps, Front Turn Signal, Sidemarker, and Parking Lamps To replace one of these bulbs: 1. Open the hood. See Hood Release on page 5-11 . 2. Remove the three headlamp assembly attachment screws. 3. Pull the headlamp assembly toward you to release it from the hidden, lower headlamp mount.
5. Pull the bulb straight out from the socket. 6. Push the new bulb into the socket and reinstall the socket into the headlamp assembly by turning it clockwise. 7. Reconnect the electrical connector. 8. Push the headlamp back into the lower headlamp mount carefully.
2. Remove the taillamp screw covers. 3. Remove the taillamp screws. 4. Pull the taillamp assembly towards you. 5. Turn the bulb socket counterclockwise to remove the bulb socket from the taillamp assembly. 6. Pull the bulb out of the bulb socket. 7. Push the new bulb straight into the bulb socket until it clicks.
License Plate Lamp To replace one of these bulbs: 1. Remove the two screws holding each of the license plate lamps to the liftgate handle. 2. Turn and pull the license plate lamp down through the liftgate opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Maintenance Replacement Parts on page 6-13 .
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall.
(E) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG) : Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance.
(B) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of Transportation) code is the Tire Identification Number (TIN).
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Tire Terminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure. Light Truck (LT-Metric) Tire : A tire used on light duty trucks and some multipurpose passenger vehicles.
Sidewall : The portion of a tire between the tread and the bead. Speed Rating : An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction : The friction between the tire and the road surface. The amount of grip provided.
Inflation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inflation or over-inflation is all right.
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under-inflated. Check the tire’s inflation pressure when the tires are cold.
If your vehicle has P235/50R18 size tires, they will require inflation pressure adjustment when driving your vehicle at speeds of 100 mph (160 km/h) or higher. Set the cold inflation pressure to the maximum inflation pressure shown on the tire sidewall, or 35 psi (241 kPa), whichever is lower.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly.
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
The TPMS sensors can also be matched to each tire/ wheel position by increasing or decreasing the tire’s air pressure. If increasing the tire’s air pressure, do not exceed the maximum inflation pressure indicated on the tire’s sidewall.
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 5-67 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 5-63 . Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 5-103 . { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Dif ferent Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover.
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired).
Used Replacement Wheels { CAUTION: Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 3-6 . { CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Removing the Spare Tire and Tools If your vehicle has the rear compartment storage panel/cover, you will have to remove it to access the load floor. See Rear Compartment Storage Panel/Cover on page 2-42 for more information. To access the spare tire and tools: 1.
5. Remove the wing-bolt holding the jack and then remove it. 6. Remove the hook and loop fastener straps holding the bag containing the wheel wrench. Remove the wheel wrench from the bag.
5. Attach the wheel wrench to the jack bolt head and turn the wheel wrench clockwise. That will raise the lift head a little. 6. Place the jack near the flat tire. Notice: Make sure that the jack lift head is in the correct position or you may damage your vehicle.
With the jack head positioned correctly on the metal jacking flange, it should look like this underneath the vehicle. Do not lift the vehicle using the plastic lower body panel. 8. Put the compact spare tire near you. { CAUTION: Getting under a vehicle when it is jacked up is dangerous.
{ CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
10. Remove all of the wheel nuts. 11. Remove the flat tire. { CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
12. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel. 13. Place the compact spare tire on the wheel-mounting surface. { CAUTION: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash.
{ CAUTION: Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to a crash. If you have to replace them, be sure to get new original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque specification.
Storing a Flat or Spare Tire and Tools { CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
5. Screw the threaded wheel stow rod onto the spare tire bracket. The final position of the wheel stow rod must be turned to the farthest forward position. 6. Remove the cap, if your vehicle has one, from the center of the load floor. Position the rod through the hole.
Compact Spare Tire Although the compact spare tire was fully inflated when the vehicle was new, it can lose air after a time. Check the inflation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inflated.
Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to home furnishings may also transfer color to the vehicle’s interior. When cleaning the vehicle’s interior, only use cleaners specifically designed for the surfaces being cleaned.
Fabric/Carpet Use a vacuum cleaner with a soft brush attachment frequently to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For any soil, always try to remove it first with plain water or club soda.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
Washing Your Vehicle The best way to preserve the vehicle’s finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle.
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer/retailer. If the vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat.
Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel.
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Vehicle Identification Vehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle.
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer first. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty.
Remove the console cover to access the fuse block. Fuses Usage 1 Sunroof, Inside Rear View Mirror, Compass 2 Rear Seat Entertainment 3 Rear Wiper 4 Liftgate 5-97.
Fuses Usage 5 Airbags 6 Heated Seats 7 Driver Side Turn Signal 8 Door Locks 9 Automatic Occupant Sensing Module 10 Power Mirrors 11 Passenger Side Turn Signal 12 Amplifier 13 Steering Wheel Illuminat.
Engine Compartment Fuse Block The engine compartment fuse block is located on the driver side of the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location. To remove the fuse block cover, release the rear of the cover first, by unlocking both of the tabs in the back.
Fuses Usage 1 Cooling Fan 2 2 Cooling Fan 1 3 Auxiliary Power 4 Rear HVAC 5 Spare 6 Sun Roof 7 Antilock Brake System 8 Air Conditioning Clutch 9 Driver Side Low-Beam 10 Daytime Running Lamp 2 11 Passe.
Fuses Usage 22 Powertrain Control Module, Ignition 23 Transmission 24 Mass Airflow Sensor 25 Airbag Display 26 Spare 27 Stoplamp 28 Passenger Side Low-Beam 29 Driver Side High-Beam 30 Battery Main 3 .
When changing relays, observe the location of the notch on the old relay. Install new relays with the notch in the same location. Relays Usage 31 Ignition Main 46 Air Conditioning Compressor Clutch 47.
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-11 for more information.
Application Capacities English Metric Fuel Tank Front-Wheel Drive 20.5 gal 77.6 L All-Wheel Drive 16.6 gal 62.8 L Transmission Fluid Automatic 5-Speed AF33 Transmission 4.1 qt 3.9 L Automatic 6-Speed 6T70 Transmission 9.5 qt 9.0 L Wheel Nut Torque 100 lb ft 140 Y All capacities are approximate.
Maintenance Schedule ..................................... .6-2 Introduction .................................................. .6-2 Maintenance Requirements ............................. .6-2 Your Vehicle and the Environment ................... .6-2 Using the Maintenance Schedule .
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details.
Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather.
The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-11 and Maintenance Replacement Parts on page 6-13 . When the vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle.
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter. See Engine Oil on page 5-15 . Reset oil life system. See Engine Oil Life System on page 5-18 . An Emission Control Service. •• Visually check for any leaks or damage.
Additional Required Services The following services should be performed at the first maintenance service ( I or II ) after the indicated miles (kilometers) shown for each item.
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc.
(i) Drain, flush, and refill cooling system. This service can be complex; you should have your dealer/retailer perform this service. See Engine Coolant on page 5-23 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and filler neck.
At Least Once a Month Tire Inflation Check Inspect the vehicle’s tires and make sure they are inflated to the correct pressures. Do not forget to check the spare tire. See Inflation - Tire Pressure on page 5-59 . Check to make sure the spare tire is stored securely.
Automatic Transmission Shift Lock Control System Check { CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. • To check the parking brake’s holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal.
Usage Fluid/Lubricant Hydraulic Power Steering System (3.6L V6 engine only) GM Power Steering Fluid (GM Part No. U.S. 89021184, in Canada 89021186). 5-speed Automatic Transmission (3.4L V6 engine only) Use only T-IV Automatic Transmission Fluid (GM Part No.
Maintenance Replacement Parts Replacement parts identified below by name, part number, or specification can be obtained from your dealer/retailer. Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 22676970 A1627C Engine Oil Filter 3.
Engine Drive Belt Routing 3.4L V6 Engine 3.6L V6 Engine 6-14.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 . Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-16.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-17.
Maintenance Record (cont’d) Date Odometer Reading Serviced By Maintenance I or Maintenance II Services Performed 6-18.
Customer Assistance and Information .............. .7-2 Customer Satisfaction Procedure ..................... .7-2 Online Owner Center ..................................... .7-5 Customer Assistance for Text Telephone (TTY) Users ......................
Customer Assistance and Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Pontiac. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments.
STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However, if you continue to remain unsatisfied after following the procedure outlined in Steps One and Two, you can file with the BBB Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps One and Two, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program.
Online Owner Center Online Owner Center (U.S.) — www.gmownercenter.com/pontiac Information and services customized for your specific vehicle — all in one convenient place.
Customer Assistance for Text Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Pontiac has TTY equipment available at its Customer Assistance Center. Any TTY user in the U.S.
GM Mobility Reimbursement Program This program, available to qualified applicants, can reimburse you up to $1,000 of the cost of eligible aftermarket adaptive equipment required for your vehicle, such as hand controls or a wheelchair/scooter lift. The offer is available for a very limited period of time from the date of vehicle purchase/lease.
Coverage Services are provided up to 5 years/ 100,000 miles (160 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered. In Canada, a person driving the vehicle without permission from the owner is not covered. Roadside Assistance is not a part of the New Vehicle Limited Warranty.
Services Not Included in Roadside Assistance • Impound towing caused by violation of any laws. • Legal fines. • Mounting, dismounting or changing of snow tires, chains, or other traction devices. • Towing or services for vehicles driven on a non-public road or highway.
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience.
Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer’s shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service.
Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualified technician using the proper equipment and quality replacement parts. Poorly performed collision repairs diminish your vehicle’s resale value, and safety performance can be compromised in subsequent collisions.
Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are significant differences in the quality of coverage afforded by various insurance policy terms.
• Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identification Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle.
Reporting Safety Defects Reporting Safety Defects to the United States Government If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traff ic Safety Administration (NHTSA) in addition to notifying General Motors.
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks.
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven.
To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.
A Accessories and Modifications ............................ 5 - 3 Accessory Power Outlets ................................. 3-18 Adding Equipment to Y our Airbag-Equipped V ehicle ....................................................... 1-72 Additives, Fuel .
Automatic Headlamp System ............................ 3-14 Automatic T ransmission Fluid .......................................................... 5-22 Operation ........................................... 2-22, 2-25 B Battery ......................
Check Engine Lamp .............................................. 3-34 Checking Things Under the Hood ...................... 5-10 Chemical Paint Spotting ................................... 5-94 Child Restraints Child Restraint Systems ................
Customer Assistance Information (cont.) Customer Assistance Off ices ........................... 7 - 6 Customer Satisfaction Procedure ..................... 7 - 2 GM Mobility Reimbursement Program ............... 7 - 7 Reporting Safety Defects to General Motors .
Electronic Immobilizer P ASS-Key ® III+ ........................................... 2-16 Electronic Immobilizer Operation P ASS-Key ® III+ ........................................... 2-17 Engine Air Cleaner/Filter ...................................
Fuel (cont.) Filling the T ank ............................................. 5 - 8 Fuels in Foreign Countries .............................. 5 - 7 G a g e ......................................................... 3-41 Gasoline Octane .................
I Ignition Positions ............................................. 2-19 Infants and Y oung Children, Restraints ............... 1-35 Inflation - T ire Pressure ................................... 5-59 Instrument Panel Brightness .....................
Light (cont.) Safety Belt Reminders .................................. 3-27 Security ..................................................... 3-38 Service All-Wheel-Drive ................................ 3-40 Service V ehicle Soon .......................
Malfunction Indicator Lamp ............................... 3-34 Manual Lumbar Controls .................................... 1 - 4 Manual Reclining Seatbacks ............................... 1 - 5 Manual Seats ...........................................
Parking Over Things That Burn ................................. 2-33 Passenger Airbag Status Indicator ..................... 3-29 Passenger Compartment Air Filter ..................... 3-23 Passenger Sensing System .............................. 1-66 Passing .
Removing the Flat T ire and Installing the Spare T ire .................................................. 5-78 Removing the Spare T ire and T ools ................... 5-77 Replacement Bulbs ......................................... 5-49 Replacement Parts, Maintenance .
Service (cont.) Doing Y our Own Work ................................... 5 - 4 Engine Soon Lamp ...................................... 3-34 Publications Ordering Information ................... 7-16 V ehicle Soon Light ................................
T ilt Wheel ........................................................ 3 - 6 T ime, Setting .................................................. 3-66 T ire Pressure Light ............................................. 3-34 T ires ..........................
V ehicle Data Recording and Privacy .................. 7-17 V ehicle Identification Number (VIN) ............................................. 5-95 Service Parts Identification Label ................... 5-95 V ehicle Personalization D I C ..........
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pontiac 2009 torrent c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pontiac 2009 torrent - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pontiac 2009 torrent, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pontiac 2009 torrent va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pontiac 2009 torrent, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pontiac 2009 torrent.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pontiac 2009 torrent. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pontiac 2009 torrent ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
