Manuel d'utilisation / d'entretien du produit PX2411MW du fabricant Planar
Aller à la page of 26
4.
The information contained in this document is subject to change without notice. This document contains proprietary informa tion that is protected by copyright.
TABLE OF CONTENTS ----------------------------------------------------------- 1 ------------------------------------------------ 2 ----------------------------- 3 Product r egistration and t echnical .
1 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED .
2 PRECAUTIONS • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable ca rt, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
3 SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent ligh t, the screen may flicker during initial use. Turn off the Power Swit ch and then turn it on again to make sure the flicker disappears.
INSTALLATION INSTRUCTIONS 1 Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down. 2 Install the Stand-Base to the Monitor. 3 Fix the Monitor with the Stand by the screw 2 firmly, and the knob of the scew push down.
5 CONTROLS AND CONNECTORS SIGNAL CABLE Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 2 Connecting Cables 1. Power Cable 2. HDMI Cable 3. DVI Cable 4. D-SUB Cable 5 Audio cable Connecting the Signal Cable : and the other end to a computer or a video source .
6 ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s an gle to your own preference. • Hold the stand so you do not toppl e the monitor when you change the monitor’s angle.
7 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Fi gure 4). By changing these settings, the picture can be adjusted to your personal preferences.
8 FRONT PANEL CONTROL • Power Button : Press this button to switch ON/OFF monitor’s power. • Power Indicator: Blue — Power On mode. Orange —Off mode.
9 HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window. 2. Press + or - to navigate through the functi ons. Once the desired function is highlighted, press the MENU-button to acti vate it. If the function selected has a sub-menu, press + or - again to navigate through the sub-menu functions.
10 ADJUSTING THE PICTURE Main Menu Item Main Menu Icon Sub Menu Description Enhances Contrast Ratio Note: When this function is turned "On" you cannot adjust the current settings for Contrast, Brightness, ECO mode or Gamma.
11 Main Menu Item Main Menu Icon Sub Menu Description.
12 Main Menu Item Main Menu Icon Sub Menu Description.
13 Main Menu Item Main Menu Icon Sub Menu Description.
14 PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, co mmunicate additional information about its display capabilities.
15 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play * C h e c k .
16 CLOCK (pixel frequency) controls the numb er of pixels scanned by one horizontal sweep. If the frequency is not correct, th e screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel cloc k signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture.
1 7 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 60cm(23.6") Pixel pitch 0.2715 ( H ) × 0.2715 ( V ) R,G,B Analog Interface Video DVI HDMI Input Separate Sync. H/V TTL H-Frequency Analog:24-80kHz,Digital: 30kHz – 80kHz V-Frequency Analog&Digital: 5 5 -75Hz Display Colors 16.
18 FACTORY PRESET TIMING TABLE 640 x 480 31.469 59.94 640 x 480 35 66.667 VGA 640 x 480 37.861 72.809 Mac VGA 640 x 480 37.5 75 Dos-mode 720 x 400 31.469 70.087 800 x 600 35.156 56.25 800 x 600 37.879 60.317 800 x 600 48.077 72.188 SVGA 800 x 600 46.875 75 Mac SVGA 832 x 624 49.
1 9 CONNECTOR PIN ASSIGNMENT 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14. V-Sync 7.
2 0 19 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. TMDS Data 2+ 11. TMDS Clock Shield 2. TMDS Data 2 Shield 12. TMDS Clock- 3. TMDS Data 2- 13. CEC 4. TMDS Data 1+ 14. N.C. 5. TMDS Data 1 Shield 15. DDC SCL 6. TMDS Data 1- 16.
2 1 Wall Mounting (Optional) Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk-mounted to a wall-mounted display, do the following: 1. Verify that the Power button is turne d Off, then disconnect the power cord.
2 2 Product Registration and Technical Support Register Your Planar Products Today Thank you choosing Planar. To assure you receiv e all the benefits of your Planar product and services, re gister your Planar product today. Visit our website to register your product at http://www.
Q41G240193511A.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Planar PX2411MW c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Planar PX2411MW - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Planar PX2411MW, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Planar PX2411MW va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Planar PX2411MW, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Planar PX2411MW.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Planar PX2411MW. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Planar PX2411MW ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
