Manuel d'utilisation / d'entretien du produit PT7700 du fabricant Pelco
Aller à la page of 25
C997M 3500 Pelco W ay , Clovis, CA 93612-5699 • (559) 292-1981 • (800) 289-9100 • F AX (800) 289-9150 W ARNING! ® W arning! When lifting, transporting, or un- packing the PT7700 Series pan/tilt systems, DO NOT use the camera enclosure as a handle.
Pelco Manual C397M (4/98) 1 ® Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 International Custome.
2 Pelco Manual C397M (4/98) LIST OF ILLUSTRA TIONS Figur e Page 1 PT7700 Series Input Wiring Diagram ................................................ 8 2 PT7700 Series Connector ................................................................. 9 3 T ilt Limit Stop Adjustment .
Pelco Manual C397M (4/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed.
4 Pelco Manual C397M (4/98) 2.0 DESCRIPTION The PT7700 systems combine an environmental camera enclosure, pan/tilt as- sembly , and receiver/driver into a single unit that you can install indoors or out- doors. Y ou can install 2/3-inch (1.69 cm) and 1-inch (2.
Pelco Manual C397M (4/98) 5 3.0 INST ALLA TION 3.1 MOUNTING Attach the base of the pan/tilt system to a flat surface. If you use a wall or pedestal mount, follow the instructions that are provided with the mount. Make sure the mounting surface can support four (4) times the weight of the pan/tilt system.
6 Pelco Manual C397M (4/98) j. On the bottom of the enclosure, remove the vent grill and filters at the front of the enclosure. Replace the grill with one of the vent cover plates that was attached to the camera sled as loose equipment. k. On the bottom of the enclosure, attach the other vent cover plate over the grill at the rear of the enclosure.
Pelco Manual C397M (4/98) 7 3.3 WIRING 1. Route the six-foot power/video/control cable through the wall or pedestal mount if applicable. 2. Connect the end of the cable with the 16-pin connector to the mating connec- tor in the base of the pan/tilt unit.
8 Pelco Manual C397M (4/98) Figure 1. PT7700 Series Input Wiring Diagram.
Pelco Manual C397M (4/98) 9 PT7729RX PT7723RX-1 PT7729RX-1 PT7729RX-3 PT7729RX-1/SL Base Connector Pin Assignments PT7729WX PT7723WX-1 PT7729WX-1 PT7729WX-3 Base Connector Pin Assignments PT7729RX-1/PP PT7729RX-3/PP With Alarm Outputs Base Connector Pin Assignments Figure 2.
10 Pelco Manual C397M (4/98) 3.4 TESTING SYSTEM AND ADJUSTING LIMIT STOPS T o test the system and adjust the limit stops: 1. Loosen the two pan limit stops at the base of the pan/tilt. 2. T urn on power . 3. T est the system by moving the pan/tilt to the left, right, up and down.
Pelco Manual C397M (4/98) 11 4.0 OPERA TION Refer to the manual for your control equipment for operating the pan/tilt system. If your enclosure has a thermostatically controlled blower , the thermostat is set to turn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and to turn the fan off be- tween 62 ° and 78 ° F (17 ° and 26 ° C).
12 Pelco Manual C397M (4/98) 5.0 TROUBLESHOOTING Fuses are located inside the left cover of the pan/tilt unit. Fuses F1 (mother board) and F2 (camera) are 2/10-ampere, slow-blow fuses. F3 (pan/tilt) is a 1-ampere, slow-blow fuse. T o order fuses F1 and F2, specify the part number FUS2/10SB.
Pelco Manual C397M (4/98) 13 6.0 MAINTENANCE Perform the following maintenance at six-month (or more often in harsh environ- ments) intervals to prolong the operational life and appearance of the equipment. Window and Filters 1. Clean the window with a mild nonabrasive detergent in water and a soft cloth to maintain picture clarity .
14 Pelco Manual C397M (4/98) Tilt Adjustments and Lubrication 10. Remove the plastic cover on the right side of the pan/tilt unit. 1 1. Refer to Figure 5. V erify that the worm (B) is fully seated in the worm gear (A). If it is not, turn the two nuts (C) to lift the worm.
Pelco Manual C397M (4/98) 15 7.0 EXPLODED ASSEMBL Y DIAGRAMS Figure 6. Exploded Assembly Diagram for Blower and Circuit Board SCREWS COME WITH BLANKING PLA TE 2 1 4 5 6 7 F G H 12 8 B A B E 9 A B C 10.
16 Pelco Manual C397M (4/98) T able A. Parts List (Figure 6) Item Qty Description Part Number 1 1 V ent Grill 57004005COMP 2 2 Foam Filter EH550010045 4 1 Circuit Board Insulator EH450010256 5 1 Circu.
Pelco Manual C397M (4/98) 17 Figure 7. Exploded Assembly Diagram for Heaters and Circuit Board T able B. Parts List (Figure 7) Item Qty Description Part Number 1 1 Bracket/Heater Sink 57004020COMP 2 2.
18 Pelco Manual C397M (4/98) Figure 8. Wiring Diagram for Enclosure Circuit Board.
Pelco Manual C397M (4/98) 19 Figure 9. Component Locations for Enclosure Circuit Board Figure 10. Layout of T races on Enclosure Circuit Board.
20 Pelco Manual C397M (4/98) 8.0 SPECIFICA TIONS SYSTEM Input Voltage: 120 or 230 VAC, 50/60 Hz Power Requirements: PT7729RX, PT7729WX 0.35 A (42 vA) PT7729RX-1, PT7723RX-1, PT7729RX-1/PP, PT7729RX-1/SL, PT7729WX-1, PT7723WX-1 1.7 A (204 vA) PT7729RX-3, PT7729RX-3/PP, PT7729WX-3 1.
Pelco Manual C397M (4/98) 21 PAN/TILT Construction Body: Aluminum plate Side Covers: Vacuum-formed ABS plastic, UV protected Pan: 0-355 ° movement in horizontal plane, except PT7729RX-1/SL, which has.
22 Pelco Manual C397M (4/98) Wiretron Receiver/Driver Fuses: One 1 A, 3 AG type Two 2/10 A, 3 AG type Control Method: 15 pulse train (pulse width modulated) Pulse Amplitude: 35 mA current loop Cable R.
Pelco Manual C397M (4/98) 23 Figure 1 1. Dimension Drawing MODEL “A” “B” PT7729RX 32.50 (82.55) 29.00 (73.66) PT7729RX-1 PT7729RX-1/SL PT7729RX-1/PP PT7729RX-3 PT7729RX-3/PP PT7729WX PT7729WX-1 PT7729WX-3 PT7723RX-1 26.
24 Pelco Manual C397M (4/98) 9.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Pelco PT7700 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Pelco PT7700 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Pelco PT7700, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Pelco PT7700 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Pelco PT7700, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Pelco PT7700.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Pelco PT7700. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Pelco PT7700 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
