Manuel d'utilisation / d'entretien du produit MODEL 2707/I du fabricant Patton electronic
Aller à la page of 24
USER MANUAL MODEL 2707/I G.703 NTU with 10Base-T Ethernet Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M2707I-UM Doc# 08625U2-001 Rev .
2 1.0 Warranty Information ................................................................. 4 1.1 Radio and TV Interference ............................................................ 4 1.2 CE Notice .................................................
3 B.9 Diagnostics ................................................................................. 21 B.10 Indicators .................................................................................... 21 B.11 Configuration .........................
4 1.0 W ARRANTY INFORMATION P atton Electronics warrants all Model 2707/I components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment.
5 als A uthorization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Ser vices at: • T el: +1 (301) 975-1007 • Email: support@patton.com • URL: http://www .patton.com Note P ackages received without an RMA number will not be accepted.
6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear par ts and labor .
7 3.0 PPP OPERATIONAL BACKGR OUND PPP is a protocol used f or multi-ple xed transport over a point-to-point link. PPP operates on all full duple x media, and is a symmetr ic peer-to- peer protocol, wh.
8 Figure 1. Cisco router with serial interface, configured as PPP Half Bridge. Figure 1 shows a typical Cisco router with a serial interf ace configured as a PPP Half Bridge. The router ser ial interf ace connects to the W AN via a 2707/C (V .35) E1 NTU and to the remote 2707/I with suppor t for PPP bridging.
9 4.0 CONFIGURATION The Model 2707/I f eatures configuration capability via hardware DIP s witches. This section describes all possible DIP s witch configurations of the Model 2707/I. 4.1 DIP SWITCH CONFIGURATIONS The Model 2707/I has an internal DIP switch that enables configur ation f or a wide range of applications.
10 Switch S1 settings T able 1 sho ws the settings f or DIP s witch S1-1 thru S1-8. SW1-1 Line Coding: HDB3 (default) Use Switch SW1-1 to control the Network Line Coding options. Set these options to be the same as the Line Coding given to y ou by your Service Provider .
11 The receiver recogniz es these special violations and decodes them as zeros . This method enables the network to meet minimum pulse den- sity requirements. Unless AMI is required in your application, HDB3 should be used whene ver possib le. • AMI .
12 5.0 INSTALLATION Once the Model 2707/I is properly configured, it is ready to connect to the G.703 interf ace, to the Ethernet por t, and to the power source. This section describes how to make these connections . 5.1 CONNECTING TO THE G.703 NETWORK AND ETHERNET LAN This section describes installing the G.
13 Connecting Dual Coaxial Cable (75 ohm) to the G.703 Netw ork Ref er to Figure 5 to make the proper connections . Figure 5. Rear panel, showing location of connectors Note The outer conductor of the coax cables are isolated from system ear th ground.
14 Connecting the T wisted Pair (120 ohm) to the G.703 Network Ref er to the pinout and signals chart in Figure 6 to connect the 120-ohm G.703 network channel.
15 Figure 8. 10Base-T cross-ov er cable connection Connecting the 10Base-T Ethernet P or t to a Hub The 10Base-T interf ace is configured as DTE (data terminal equipment), just like a 10Base-T netw ork interface card in a PC . Theref ore, it “e xpects” to connect to a 10Base-T Hub using a straight-through RJ-45 cable .
16 DC Power . The 36-60 VDC DC to DC adapter is supplied with the DC version of the Model 2707/I. The black and red leads plug into a DC source (nominal 48VDC) and the barrel power connector plugs into the barrel power supply jac k on the 2707/I. (See Figure 10).
17 6.0 OPERATION When the Model 2707/I has been properly configured and installed, it should operate transparently . This section descr ibes power-up , LED sta- tus monitors, and the b uilt-in loopback test modes .
18 T able 2: LED descriptions LED Description E1 Link (Active Green) Solid g reen (On) indicates that the end to end E1 Link is up , signifying that the link is active .
19 6.3 OPERATING LINE LOOPBACK (LL) The Line Loopback (LL) test chec ks the operation of the local Model 2707/I, and is perf ormed separately on each unit. Figure 12. Line loopback f or a networ k ter mination application T o perform an LL test, set DIP s witch S1-2 to On .
20 APPENDIX A G.703 SPECIFICATIONS A.1 NETWORK DATA RATE 2.048 Mbps A.2 NETWORK CONNECTOR RJ-48C/Dual Coax BNC A.3 NOMINAL IMPEDANCE 75/120 ohm A.4 LINE CODING Selectable AMI or HDB3 A.5 LINE FRAMING G.703 (Unframed) A.6 CLOCKING Internal or Networ k (Receive Reco ver) A.
21 APPENDIX B ETHERNET 10BASE-T SPECIFICATIONS B.1 DTE INTERFACE 10Base-T on RJ-45F B.2 DTE DATA RATES 10 Mbps B.3 LAN CONNECTION RJ-45, 10Base-T , 802.3 Ether net B.4 PROTOCOL PPP (RFC 1661) with Bridging Control (RFC 1638) B.5 MAC ADDR ESS T ABLE SIZE 4096 entries B.
22 B.12 POWER SUPPLY 5 VDC external power supply 100–240V AC , 50–60Hz, 0.4A B.13 HUMIDITY Up to 90% non-condensing B.14 T EMPERATURE 0–50°C (32–122°F) B.
23 APPENDIX C F ACTOR Y REPLACEMENT P AR TS AND ACCESSORIES P atton Model # Description 2707/C G.703 NTU with a V .35 interface 2707/D G.703 NTU with an X.
24 Cop yright © 2006 P atton Electronics Company All Rights Reser ved..
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Patton electronic MODEL 2707/I c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Patton electronic MODEL 2707/I - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Patton electronic MODEL 2707/I, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Patton electronic MODEL 2707/I va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Patton electronic MODEL 2707/I, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Patton electronic MODEL 2707/I.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Patton electronic MODEL 2707/I. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Patton electronic MODEL 2707/I ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
