Manuel d'utilisation / d'entretien du produit SMD2000-24T du fabricant Paradyne
Aller à la page of 32
1 SMD2000-24T 24-P or t SHDSL Mini DSLAM Installation Instructions Document Number SMD2-A2- GN11-00 Ju ly 2005 Contents Softwar e and Firmware License Agree ment .............. ............. ............. ......... 2 Product Documentation Online .....
2 Software and Firmwar e License Agreement The ter ms and conditions of this License Ag reement (the “Agreeme nt”) will apply to the software and/or firmware (individually or collectively the “S.
3 b . ANY AND ALL IMPLIED W ARRANTIES , INCLUDING WITHOUT LIMIT A TION IMPLIED W ARRANTIES OF MERCHANT ABILITY , FITNESS FOR A P ARTICULAR PURPOSE AND NON-INFRINGEMENT .
4 Unpacking and Inspecting the Equipment HANDLING PRECA UTIONS FOR ST A TIC-SENSITIVE DEVICES This pr oduct is designed to pr otect sensitive components from damage due to electr ostatic discharge (ESD) d uring normal operation.
5 Installing Uplink Interf ace Modules (Optional) An SMD2000-24T d oes not require insta llation of an Uplink Interface Module (UIM) f or operational pur poses. A UIM offers additional upstream network por ts to supplement the two T1 uplink por ts already provided.
6 2. Mount the UIM on the SMD2000-24T Print ed Circuit Board (PCB). A UIM may be installed in either P or t 1 or P or t 2, or both for redundancy purposes. Using a Phillips screwdriver , remov e the flathead screws from both sides of the chosen por t on the chassis faceplate.
7 5. Secure the f aceplate. Using a Phillips screwdriver , secure the UIM faceplate to the SMD2000-24T faceplate with the two flathead screws included in your UIM packaging. 6. Replace the c hassis co ver . Replace the chassis cover and secure with the original e ight flathead screws as depicted in Step 1 on page 5.
8 Rack Installation Procedure T o insta ll the SMD2 000-24T in a rack: 1. Using a Phillips screwdriver , attach the two provided rac k mount brack ets to the sides of the SMD2000-24T with t he ten provided brack et screws.
9 P owering Up the SMD2000-24T C AUTION : T ur n your DC pow er source off until you ha ve completed connection of the SMD2000-24T as descr ibed below . Do not operate your SMD2000-24T without a ground connection. Procedure T o connect the SMD20 00-24T to power: 1.
10 The two ter minal blocks on the SMD2000-24T are independent feeds. Chassis power is supplied by only one termin al bloc k at a time; the second su pply is merely backup . Likewise , the two ter minal blocks do not load-share. Each terminal block must be supplied with the adequate amperage to r un the chassis.
11 7. V erify the connection. T urn your power source ON. The PWR (po wer) LED on your SMD2000-24T f aceplate will illuminate solid green to indicate that the chassis is receiving power . Connecting the SHDSL RJ21 Cable Procedure T o connect the SHD SL cable to the SMD2000-24T RJ21 connector : 1.
12 3. Slide the RJ21 plug connector of your SHDSL cable under neath the hook-and -loop f astener from the right and press it fir mly into the RJ21 socket on the chassis.
13 The speed and data passing capability of mult ip le SHDSL lines, as used f or one networ k connection, is cumulative. F or example, loop bonding three SHDSL lines for one network connection nets three times the speed and da ta passing capability of a single-line SHDSL connection.
14 Connecting the Uplink Lines T o connect the SMD2000-24T to T1 ser vice: 1. Configure the T1 uplinks. No configuration is necessar y f or the SM D2000-24T to operate at default settings . Howe ver , if you wish to run uplinks at settings other than the SMD2000 -24T defaults , configure the uplinks pr ior to connection.
15 Default Settings SHDSL Parameter Defaults T1 Uplink Parameter Defaults T able 1. SHDSL Defaul ts Parameter Default Backbone-VLA N 0 (off) Circuit Identification n/a (no default) Flood Uplink IP Range 1 0.0.0.0 – 255.255.255.255 IP Range 2 0.0.0.0 – 0.
16 System and Management Defaults No configuration is necessar y f or an SM D2000-24T to operate at default settings. User Access Defaults T able 3. System and Management Defaults Parameter Default IP Address 192.168.254.252 Subnet Mask 255.255.255.0 Gatew ay 0.
17 Data Storage Configuration backup is inherent in the SMD2000-24T . Def ault parameters remain in place unless changed us ing the CL I, web management system, or SNMP . Memory P aramete r configurations are automatically recorded in both Random Access Memory (RAM) and Non-V olatile Random Access Memor y (NVRAM).
18 SMD2000-24T T emplate An SMD2000-24T templa te file records a ll management and por t configurations except IP Address. SHDSL Port T emplate A SHDSL por t confi guration file records all o f one por t's configurations except Circuit ID .
19 Reset Button The reset button is a small, unmarked b utton just to the right of the T1 up link LEDs on the chassis faceplate . The button is rece ssed and you need a paper clip, mechanical pencil, or similar tool to press i t. System Reset A system reset will clear all statistica l data (stored in RA M) and restart the SMD2000-24T .
20 Command Line Interface f or 4000E and 12000E BACs, Micro DSLAMs, and Network Extenders User 's Guide (Document Number CLI-A2-GB20) o r the Network Management System User's Guide (Document Number NMS-A2 -GB20) for furt her inf or mation.
21 LNK (10/100 Ethernet Manage- ment Link) Flashing green 100 Mbps management connection is established and active T raffic is flowing at 100 Mbps. Solid green 100 Mbps management connection is established No current traf fic flow . Flashing amber 10 Mbps management connection is established and active T raffic is flowing at 10 Mbps.
22 AL: T1 Alarm Po r t 1 and 2 No illumination T1 uplink connection is operational An established T1 uplink connection has no alar m indications and is operational UNLESS the T1 LK LED remains unli t as well, in which case the T1 uplink connection i s in Red Alarm.
23 Pin Assignments SHDSL RJ21 Pinouts Pins 25 and 50 are not used . T able 10. SHDSL RJ21 Pinouts Por t Connector Pins (Ring, Tip) Port Connector Pins (Ring, Tip) P or t 1 1, 26 P or t 13 13, 38 P or .
24 10/100BaseT RJ45 Pinouts T1 RJ48C Pin Assignments T able 11. Ethernet RJ45 Connection Pin Connection 1R x + 2R x – 3T x + 4 not used 5 not used 6T x – 7 not used 8 not used T able 12.
25 DB9 to 8-Pin Modular Adapter Pinouts T o connect the COM p or t to the DB9 serial por t of a PC, use an adapter wired as sh own: Pins not shown are unused.
26 T echnical Specif ications T able 14. SMD2000-24T T echnical Specif ications Specif ication Criteria Bandwidth and Distan ce Capabilities – SHDSL Po r t s Def ault is 272 kbps at up to 20,200 ft .
27 EMI Notices United States – EMI Notice This equipment has been teste d and found to comply with the limits f or a Class A digital de vice, pursuant to P a r t 15 of the FCC ru les. These limits are designed to provide reasonable protection against har mful interf erence when the equipment is operated in a commercial environment.
28 A plug and jack used to connect this equipment to the premises wir ing and teleph one network must comply with the applicable FCC Part 68 rules and require ments adopted by the A CT A.
29 Jap a n N o ti c e Class A ITE This is a Class A product based on the sta ndard of the V oluntar y Control Council for interf erence by Inf or mation T echnology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance ma y arise.
30 Important Safety Instructions 1. Read and follow all warning notices an d instructions marked on the product o r included in the manual . 2. Slots and openings in the cabinet are provided for v entilation . T o ensure reliable operation of the product and to protec t it from overheating, these slots and openings must not be block ed or covered.
31 W arranty , Sales, Service, and T raining Inf ormation Contact your local sales representative , ser vic e representati ve , or distributor directly f o r any help needed.
32 *SMD2-A2-GN11-00* *SMD2-A2-GN11-00*.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Paradyne SMD2000-24T c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Paradyne SMD2000-24T - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Paradyne SMD2000-24T, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Paradyne SMD2000-24T va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Paradyne SMD2000-24T, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Paradyne SMD2000-24T.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Paradyne SMD2000-24T. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Paradyne SMD2000-24T ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
