Manuel d'utilisation / d'entretien du produit 5620 du fabricant Paradyne
Aller à la page of 20
TM 1 Hotwire 5620 RTU Customer Premises Installation Instructions Document Number 5620-A2-GN1 1-10 June 1999 Before Y ou Begin The Hotwire 5620 RTU (Remote T ermination Unit) interoperates with the Hotwire 8510 DSL Card in the DSLAM (Digital Subscriber Line Access Multiplexer) system.
2 Package Checklist V erify that your package contains the following: - Model 5620 Remote T ermination Unit (RTU) - DSL interface cable with RJ1 1 connectors - Power cord with power transformer Refer to Cables & Connectors, page 14, for standard pin numbers.
3 97-15346-02 Punchdown Block or NID DSL Jack RTU New Wiring Connections Existing Wiring (POTS) Customer Premises (CP) DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) Demarcation Po.
4 DSL Access without a POTS Splitter When the Hotwire 5620 RTU is installed without a POTS splitter , a second telephone wiring pair is needed for DSL access.
5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to an RJ1 1 jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
6 3. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. In the following example, a NID is used without a POTS splitter . It includes an existing POTS line and a second pair installed for DSL access.
97-15300a RJ11 W all Jack or 7 The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack. It may be necessary to install a standard single RJ1 1 jack or replace a single jack with a double RJ1 1 jack.
8 Installing the Hotwire 5620 R TU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors. Procedur e 1. Use the supplied RJ1 1 6-pin cable for the DSL connection. Insert one end of the cable into the jack labeled DSL.
9 2. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET . Use a straight-through cable and connect the other end to an Ethernet hub.
10 3. Insert the power cord’s round end into the jack labeled POWER. Plug the transformer into an ac outlet. 98-15836 PO WER ETHERNET DSL Hotwire RTU Po w e r Jack or T ransformer or The RTU hardware installation is now complete. When the power cord is installed, the RTU goes through a power-on self-test.
11 Optional R TU W all Placement The Hotwire 5620 RTU is designed for tabletop placement. The R TU can also be mounted on a wall. T o mount an RTU, you will need: - Three slotted-head #6 self-threadin.
12 R TU Hardwar e T emplate F ront (LEDs) 98-16171 5.43" 7.55" T o Bottom Hole.
13 Status LEDs All of the LEDs turn on and off during the power-on self-test. After a successful self-test, the LEDs should appear as indicated in BOLD in the Condition column below . LED Condition Status PWR ON RTU has power . ALM OFF ON No active alarms.
98-15304-01 6-Pin RJ11 Plug DSL Cable Pin #1 Pin #6 14 LED Symptom Action DSL and Ethernet LEDs are on and there is no data transmission. The DSL link and the Ethernet link have been established but there is no data transmission. If the problem continues, contact the NSP .
98-16055a 8-Pin Plug Ethernet Cable Pin #1 Pin #8 15 The Ethernet interface connector uses an 8-pin, non-keyed modular plug. — T o connect to an Ethernet hub, use the straight-through connection.
16 Model 5620 R TU T echnical Specifications Item Specification * Height x Width x Depth 1.43 ″ x 6.00 ″ x 8.75 ″ (3.64 cm x 15.24 cm x 22.23 cm) Weight 1 lb.
17 ! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5620-A3-200 This device complies with Part 15 of the FCC Rules.
19 Directive 89/336/EEC – Council Directive of 3 May 1989 on the approximation of the laws of the member states relating to Electro-Magnetic Compatibility (EMC), as amended by Directive 93/68/EEC.
20 W arranty , Sales, Service, and T raining Information Contact your local sales representative, service representative, or distributor directly for any help needed.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Paradyne 5620 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Paradyne 5620 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Paradyne 5620, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Paradyne 5620 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Paradyne 5620, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Paradyne 5620.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Paradyne 5620. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Paradyne 5620 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
