Manuel d'utilisation / d'entretien du produit PT-EX500UL du fabricant Panasonic
Aller à la page of 118
Operating Instructions Functional Manual LCD Projector Commercial Use Model No. PT -EZ570U PT -EZ570UL PT -EW630U PT -EW630UL PT -EW530U PT -EW530UL PT -EX600U PT -EX600UL PT -EX500U PT -EX500UL ENGLISH KV4A Thank you for purchasing this Panasonic Product.
2 - ENGLISH Important Information Read this rst! W ARNING: THIS APP ARA TUS MUST BE EAR THED. W ARNING: T o prevent damage which may result in re or shock hazard, do not expose this appliance to rain or moisture. Machine Noise Information Ordinance 3.
Read this rst! ENGLISH - 3 Important Information FCC NOTICE (USA) Declaration of Conformity Model Number: PT -EZ570U, PT -EZ570UL, PT -EW630U, PT -EW630UL, PT -EW530U, PT -EW530UL, PT -EX600U, PT -.
Read this rst! 4 - ENGLISH Important Information IMPORT ANT : THE MOULDED PLUG (U.K. only) FOR YOUR SAFETY , PLEASE READ THE FOLLOWING TEXT CAREFULL Y . This appliance is supplied with a moulded three pin mains plug fo r your safety and convenience.
Read this rst! ENGLISH - 5 Important Information W ARNING: PO WER The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur . If the following problems occur , cut off the power supply immediately .
Read this rst! 6 - ENGLISH Important Information W ARNING: Installation work (such as ceiling mount bracket) should only be carried out by a qualied technician. If installation is not carried out and secured correctly it can cause injury or accidents, such as electric shocks.
Read this rst! ENGLISH - 7 Important Information W ARNING: ACCESSORI ES Do not use or handle the batteries improperly , and refer to the following. Failure to observe this will cause burns, batteries to leak, overheat, explode or catch re. Do not use unspecied batteries.
Read this rst! 8 - ENGLISH Important Information T o remove the battery Remote Control Battery 1 . P ress the g ui de a nd li f t th e cover . 2. Rem ove th e batter ies . CAUTION: PO WER When disconnecting the power cord, be sure to hold the power plug and power connector .
Read this rst! ENGLISH - 9 Important Information T rademarks HDMI, the HDMI logo and High-Denition Multimedia Interface is a trademark or registered trademark of HDMI • Licensing LLC. PJLink™ is a trademark or pending trademark in Japan, the United States, and other countries and region.
10 - ENGLISH With the Direct Power Of f function, you can disconnect the power cord from the wall outlet or turn of f the breaker even during projection. The inclusion of an HDMI terminal provides support for high quality video and HDMI audio. The digital zoom function allows you to focus on the crucial information during a presentation.
ENGLISH - 11 Important Information Preparation Getting Started Basic Operation Settings Maintenance Appendix Contents Be sure to read “Read this rst!”. ( pages 2 to 9) Important Information Read this rst! ....................................
12 - ENGLISH Important Information Preparation Getting Started Basic Operation Settings Maintenance Appendix Contents Image 1-10 ................................................................... 55 Image adjust.......................................
ENGLISH - 13 Important Information Precautions for Use Cautions when transporting When transporting the projector , hold it securely by its bottom and avoid z excessive vibration and impacts. Doing so may damage the internal parts and result in malfunctions.
Precautions for Use 14 - ENGLISH Important Information Cautio ns when setting the pro ject ors J When installing and using the projector with a method other than the oor standing installation using the z adjustable feet, x the projector using the ve screw holes for ceiling mounting (shown in the gure).
Precautions for Use ENGLISH - 15 Important Information Security T a ke saf e t y mea sures against f ollow ing incident s. J Personal information being leaked via this product. z Unauthorized operation of this product by a malicious third party . z Interfering or stopping of this product by a malicious third party .
Precautions for Use 16 - ENGLISH Important Information La mp J The luminous source of the projector is a mercury lamp with high internal pressure. A high pressure mercury lamp has following characteristics. The brightness of the lamp will decrease by duration of usage.
Precautions for Use ENGLISH - 17 Important Information Accessories Make sure the following accessories are provided with your projector . Numbers in the brackets ( ) show the number of accessories.
Precautions for Use 18 - ENGLISH Important Information Attention After unpacking the projector , discard the power cord cap and packaging material properly . z For lost accessories, consult your dealer . z The part numbers of accessories and separately sold components are subject to change without notice.
ENGLISH - 19 Preparation About Y our Projector Remote control (6) (4) (1) Remote control signal emitter (2) <POWER ON> button T urn the projector on. ( Æ page 38) (3) <SHUTTER>/<A V MUTE> button * <SHUTTER> button (Only for EZ570 series, EW630 series and EX600 series.
About Y our Projector 20 - ENGLISH Preparation (15) (23) (20) * (22) (19) (14) (18) (16) (26) (17) (25) (24) (21) (14) <ECO> button Display the Eco management function. ( Æ page 44) (15) <P-TIMER> button Operate the P-timer function. ( Æ page 44) (16) <FREEZE > button Pauses the projected image and sound tentatively .
About Y our Projector ENGLISH - 21 Preparation (1) Lens Release Button (2) Indicators ( Æ page 22) (3) Daylight view sensor ( Æ page 57) (4) Lamp cover ( Æ page 97) The lamp unit is located inside.
About Y our Projector 22 - ENGLISH Preparation Side control and Indicators (1) (2) (4) (5) (7) (6) (8) (9) (1) < > button T urn the projector on or off. (2) <MENU> button Displays the menu screen. ( Æ page 47) (3) <SHUTTER>/<A V MUTE> button * <SHUTTER> button (Only for EZ570 series, EW630 series and EX600 series.
About Y our Projector ENGLISH - 23 Preparation Rear terminals (1) Remote control signal receiver (Back) The infrared remote receiver is also located in the front and top . (2) LAN Connect the LAN cable. (3) MONITOR OUT This terminal can be used to output the incoming analog RGB signal from INPUT 1-3 terminals to the other monitor .
24 - ENGLISH Preparation Using Remote control Installing and Removing batteries Open the cover 1 ) Install batteries and close the cover 2 ) (Insert the – side rst.
ENGLISH - 25 Getting Started Setting up Projection method Y ou can use the projector with any of the following 4 projection methods. T o set the desired method in the projector .
Setting up 26 - ENGLISH Getting Started Removing and attaching the projection lens When replacing the lens or using an optional lens, install the lens by following the instructions below . Ask the sales dealer for detailed information of the optional lens specications.
Setting up ENGLISH - 27 Getting Started Screen size and throw distance Place the projector referring to the diagram on the right and the gures of throwing distance.
Setting up 28 - ENGLISH Getting Started For the screen aspect ratio of 16:9 (Unit: m) z Lens type The standard zoom lens The lens of optional accessories Height position (H) * 2 Fixed-focus Lens Short Zoom Lens Long Zoom Lens Ultra Long Zoom Lens Model number of projection lens - - - ET -EL W21 ET -EL W20 ET -EL T20 ET-EL T21 Throw ratio * 1 1.
Setting up ENGLISH - 29 Getting Started J Projection distance by projection lens (for EW630 series and EW530 series) For the screen aspect ratio of 16:10 (Unit: m) z Lens type The standard zoom lens T.
Setting up 30 - ENGLISH Getting Started For the screen aspect ratio of 4:3 (Unit: m) z Lens type The standard zoom lens The lens of optional accessories Height position (H) * 2 Fixed-focus Lens Short Zoom Lens Long Zoom Lens Ultra Long Zoom Lens Model number of projection lens - - - ET -EL W21 ET-EL W20 ET -EL T20 ET -EL T21 Throw ratio * 1 2.
Setting up ENGLISH - 31 Getting Started For the screen aspect ratio of 4:3 (Unit: m) z Lens type The standard zoom lens The lens of optional accessories Height position (H) * 2 Fixed-focus Lens Short Zoom Lens Long Zoom Lens Ultr a Long Zoom Lens Model nu mber of proje ction lens - - - ET -EL W21 ET-EL W20 ET -EL T20 ET -EL T21 Throw ratio * 1 1.
Setting up 32 - ENGLISH Getting Started If the projector is used with a screen size not listed in this manual, check the diagonal dimension (m) of your screen and calculation the projection distance using the following formula.
Setting up ENGLISH - 33 Getting Started Calculation formulas for projection distance by lens types J (for EW630 series, EW530 series) Lens type Aspect ratio Projection distance (L) formula The standard zoom lens 16:10 Min. (L W) L= 1.407382 x SD(m) - 0.
Setting up 34 - ENGLISH Getting Started Adjusting front adjustable feet The adjustable feet can be extended by turning it as shown in the gure. It is retracted by turning it in the opposite direction. (Projection angle can be adjusted vertically .) Attention Heated air comes out of the air exhaust port while the lamp is lit.
ENGLISH - 35 Getting Started Connections Before connecting to the projector Read carefully the instruction manual for the device to be connected. z T urn off the power switch of the devices before connecting cables.
36 - ENGLISH Basic Operation Powering ON/OFF Connecting the power cord Be sure to insert the attached power cord securely to its base to prevent it from coming off. Power cord holder J A power cord holder is designed to prevent the AC power cord from coming off the projector .
Powering ON/OFF ENGLISH - 37 Basic Operation ON(G)/ST ANDBY(R) indicator The <ON(G)/ST ANDBY(R)> indicator informs you the status of the power . Conrm the status of the <ON(G)/ ST ANDBY(R)> indicator before operating the projector .
Powering ON/OFF 38 - ENGLISH Basic Operation Complete peripheral connections (with a 1 ) computer , VCR, etc.) before turning on the projector . Connect the projector ’s AC power cord into an 2 ) AC outlet. The <ON(G)/ST ANDBY(R)> indicator lights red.
Powering ON/OFF ENGLISH - 39 Basic Operation Enter a PIN code PIN Code Input Dialog Box When using the side control J Press ▲▼ to enter a number . Press ► to x the number and move the red frame pointer to the next box. The number changes to .
Powering ON/OFF 40 - ENGLISH Basic Operation Press the < 1 ) > button on the side control o r the <ST ANDBY> button on the remote control, and Power off? appears on the screen. Press the < 2 ) > button on the side control o r the <POWER ON> button on the remote control again to turn off the projector .
ENGLISH - 41 Basic Operation Projecting Check the connections of the peripheral devices and connection of the power cord ( Æ page 36) and switch on the power ( Æ page 38) to start the projector . Select the image and adjust the state of the image. Selecting the image Select an input signal.
42 - ENGLISH Basic Operation Basic operations by using the remote control Using the SHUTTER/ A V MUTE button * <SHUTTER> button (Only for EZ570 series, EW630 series and EX600 series) This function allows you allows you to completely block out light to the screen.
Basic operations by using the remote control ENGLISH - 43 Basic Operation Using the MENU button This function allows you to open or close the On- Screen Menu. button Press the <MENU> button on the remote control. Note For details, please refer to “Menu Navigation”.
Basic operations by using the remote control 44 - ENGLISH Basic Operation Using the P-TIMER button Press the <P-TIMER> button on the remote control to operate the Count up/Count down function. button Press <P-TIMER> button on the remote control.
Basic operations by using the remote control ENGLISH - 45 Basic Operation Using the KEYST ONE button This function allows you to correct keystone distortion. button For EW530 series and EX500 J series. Press the <KEYSTONE> button on the remote control.
Basic operations by using the remote control 46 - ENGLISH Basic Operation Using the ZOOM +/- buttons Adjusts the zoom of the lens. buttons Press <ZOOM +/-> buttons on the remote control. Note For details, please refer to “Adjusting the image” z ( Æ page 41).
ENGLISH - 47 Settings Menu Navigation Navigating through the menu Operating procedure J For example: PT -EZ570U Press the <MENU> button. 1 ) The Main Menu screen appears.
Menu Navigation 48 - ENGLISH Settings Main menu The main menu consists of the following 9 menu items. When a main menu item is selected, the screen changes to a submenu selection screen.
Menu Navigation ENGLISH - 49 Settings Screen [ J ] Sub-menu item Factory default Page Normal - 59 Full - 59 Wide (16:9) - 59 Zoom - 59 T rue* 1 - 59 Natural wide* 2 - 59 Custom - 59 Custom adj.
50 - ENGLISH Settings Input menu Select [Input] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Input 1 Press ▲▼ to select [Input 1]. 1 ) Press ► to access the submenu. 2 ) Press ▲▼ to select [RGB(PC analog)], 3 ) [RGB(Scart)], [DVI-D], [DVI-D(HDCP)] or [HDMI].
Input menu ENGLISH - 51 Settings Y , Pb/Cb, Pr/Cr Auto The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance.
52 - ENGLISH Settings AUT O PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu.
ENGLISH - 53 Settings Manual PC adjust Select [PC adjust] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Remote Control Side Control Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector .
Manual PC adjust 54 - ENGLISH Settings Current mode Press ▲▼ to select [Current mode]. 1 ) Press ► or the <ENTER> button to 2 ) enter the next submenu to show [ H-sync freq.] and [V -sync freq.] of the connected computer . Clamp Press ▲▼ to select [Clamp].
ENGLISH - 55 Settings Image select Select [Image select] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Remote Control Side Control Dynamic For viewing pictures in a bright room. Press ▲▼ to select [Dynamic] and then press the <ENTER> button.
56 - ENGLISH Settings Select [Image adjust] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Remote Control Side Control Note Make sure you selected [Store] after adjusting settings. z Some settings can not be stored if not registered with [Store] function.
Image adjust ENGLISH - 57 Settings Color temp. Press ▲▼ to select [Color temp.]. 1 ) Press the <ENTER> button to display 2 ) the adjustment dialog box. Press ◄► to select the desired Color 3 ) temp. level. Y ou can select the desired [Color temp.
Image adjust 58 - ENGLISH Settings Sharpness Press ▲▼ to select [Sharpness]. 1 ) Press the <ENTER> button to display 2 ) the adjustment dialog box . Press ◄► to adjust the setting value. 3 ) Operation Adjustment Adjustment range Press ►.
ENGLISH - 59 Settings Screen Select [Screen] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Remote Control Side Control Normal Provide the image to t the screen size while maintaining the aspect ratio of the input signal.
Screen 60 - ENGLISH Settings Custom adj. Adjust the screen scale and position manually with this function. Press ▲▼ to select [Custom adj.]. 1 ) Press ► or the <ENTER> button to 2 ) enter the next submenu. Press ▲▼ to choose the item you 3 ) want to adjust.
Screen ENGLISH - 61 Settings Ceiling This function is used to project the image from a ceiling-mounted projector . Press ▲▼ to select [Ceiling] and then 1 ) press the <ENTER> button. Press ▲▼ to change the image. 2 ) When this function is set to [On], the picture will z be top/bottom and left/right reversed.
62 - ENGLISH Settings Sound Select [Sound] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Remote Control Side Control V olume Press ▲▼ to select [V olume] and then 1 ) press the <ENTER> button.
ENGLISH - 63 Settings Setting Select [Setting] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Remote Control Side Control Language Press ▲▼ to select [Language]. 1 ) Press ► or the <ENTER> button.
Setting 64 - ENGLISH Settings Display This function decides whether to display On-Screen Displays. Press ▲▼ to select [Display]. 1 ) Press the <ENTER> button.
Setting ENGLISH - 65 Settings Attention Be sure to note the new Logo PIN code and keep it on z hand. If you lost the number , you could no longer change the Logo PIN code setting. Picture in Picture This function is used to project two images simultaneously by placing a separate small sub screen within or next to the main screen.
Setting 66 - ENGLISH Settings HDMI setup This function is only used for HDMI input source. Press ▲▼ to select [HDMI setup]. 1 ) Press ► or the <ENTER> button. 2 ) The names for the output setting of Digital R/G/ z B vary from equipment to equipment.
Setting ENGLISH - 67 Settings Simple mode This function decides whether to activate the simple mode. Press ▲▼ to select [Simple mode] and 1 ) then press the <ENTER> button. Press ▲▼ to switch between [On] and 2 ) [Off]. On Simple mode function is off.
Setting 68 - ENGLISH Settings Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period. Press ▲▼ to select [Power 1 ) management].
Setting ENGLISH - 69 Settings Execute J Press ▲▼ to select one among the 1 ) items as below and then press the <ENTER> button. Start It executes the count up or count down function.* 1 Reset Reset the P-timer values.* 2 Exit T o exit the P-timer operation.
Setting 70 - ENGLISH Settings Press ▲▼ to select the desired items 1 ) as below . Permit the shutter operation from both the remote control and the projector's side control. Prohibit the shutter operation from the remote control. Prohibit the shutter operation from the side control.
Setting ENGLISH - 71 Settings Filter counter This function is used to set a frequency for the lter replacement. Press ▲▼ to select [Filter counter]. 1 ) Press ► or the <ENTER> button to 2 ) access the submenu items. Filter counter J Show the total accumulated time of the lter use timer setting.
72 - ENGLISH Settings Information Select [Information] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu.
ENGLISH - 73 Settings Network Select [Network] from the Main Menu (see “Navigating through the menu” on page 47), then select the item from the sub-menu. Remote Control Side Control Projector name Y ou can change the projector name to be displayed on the network.
Network 74 - ENGLISH Settings "Crestron RoomView" is a system developed by Crestron Electronics, Inc. which collectively manage and control multiple system devices connected via the network, from a computer . This projector supports "Crestron RoomView".
Network ENGLISH - 75 Settings Network connections The projector has a network fuction, and the following operations are available from the computer using the web browser control. Setting and adjustment of the projector . z Display of the projector status.
Network 76 - ENGLISH Settings Accessing from the W eb browser Activate the Web bro wser in the pe rsonal computer . 1 ) Enter the IP ad dress set b y the projec tor into the URL input eld of the Web bro wser . 2 ) Enter y our “ User name” and “ Passw ord” .
Network ENGLISH - 77 Settings Description of each item J 1 Pag e sele ct ion ta bs Click t hese t o switch p age s. 2 M onit or infor mat ion bu tt on Click t his it em, a nd the s tatu s of the p rojec tor is di splayed. 3 Proj ect or cont rol bu tt on Click t his it em to di splay t he proj ecto r cont rol page.
Network 78 - ENGLISH Settings Error information page J If [Erro r (Detail) ] is displayed in the self- diagno sis informati on display column on th e [Projector st atus ] scre en, clic k the par t to display the details of the er ror .
Network ENGLISH - 79 Settings Basic control page J T o mov e fro m another page, clic k [Projector c ontrol], th en [Basic c ontrol]. 1 Power st and by/ on co ntro l 2 U se the se to sele ct t he inpu.
Network 80 - ENGLISH Settings 5 Op erat ions o n Ke ysto ne func tio n 6 Op erat ions o n Lens shi f t 7 Op erat ions o n Zoom 8 Op erat ions o n F ocu s 9 Op erat ions o n T est pat te rn 10 Retur n .
Network ENGLISH - 81 Settings Network cong page J Y ou can c hange netwo rk sett ings on projec tor when c onnecting w ith the administrator autho rit y . LAN settings z Click [ Det ailed set up ] in the menu. 1 ) Click [ Change ] to change t he LA N settings.
Network 82 - ENGLISH Settings Ping test page J This page makes it pos sible to check w hether the net work is c onnected to th e e- mail ser ver , PO P ser ver , DNS ser ver , etc. Click [D etailed set up], then [Ping test] to displa y the Ping test page.
Network ENGLISH - 83 Settings E-mail set up page J With t his projector , if a probl em occur s or if the lamp us age time reache s a set value , an e -mai l message c an be sent to one or more pr eset e- mail addres ses ( maxi mum two addres ses ). Click [D etailed set up], then [E-mail set up] to display the E-mail setup page.
Network 84 - ENGLISH Settings E-mail set up page (continued) J 1 E nter t he E- mai l Addre ss2 of your de sired re cipi ent . 2 S elec t th e condi tio ns for sen ding e - mail . MA IL CONT ENTS : Selec t [NOR MA L ] or [SIM PLE]. ERRO R: A n error is detec ted b y self -diagn osis.
Network ENGLISH - 85 Settings Contents of mail sent J Mail with the contents shown below is sent when the e-mail settings have z been established. == = Pan asonic pro jector rep ort ( CON FI GU RE) ==.
Network 86 - ENGLISH Settings Mail with the contents shown below is sent when an error has occurred. z == = Pan asonic pro jector rep ort (ER ROR ) == = Proj ector Ty p e : PT -E Z5 7 0 Serial No : 00.
Network ENGLISH - 87 Settings Change Password page J Click [Change pas sword]. 1 Administ rator 2 User Administ rator mod e 1 Account 2 Cur rent u ser na me inpu t eld 3 Cur rent p assword i nput .
Network 88 - ENGLISH Settings CRSTRON RoomV iew page J Y ou can mo nitor or contr ol the projec tor using Room Vi ew . T o display the operation pa ge of Room View fro m W eb C ontrol screen, ac cess w ith the administrator r ights is required. ( The [CRESTRON Room View] but ton is not display ed on t he Web Control scre en for user ri ghts.
Network ENGLISH - 89 Settings Info page Click Info on t he operation pa ge. 1 Proj ect or nam e Displays the name of the p rojector . 2 M ac Addr ess Displays the M A C addres s. 3 Resolution Displays the reso lution of the proje ctor . 4 L amp H ours Displays the lamp usag e time ( conver ted value ).
90 - ENGLISH Maintenance About indicator status If an indicator turns on If a problem occurs within the projector , it will be notied with the temperature indicator <TEMP>, the lter indicator <FIL TER>, the shutter indicator <SHUTTER>*, and the lamp indicator <LAMP>.
About indicator status ENGLISH - 91 Maintenance When there is a problem with internal temperature J The status of the indicator is displayed with the following symbols.
About indicator status 92 - ENGLISH Maintenance When there is a problem with internal power J The status of the indicator is displayed with the following symbols.
About indicator status ENGLISH - 93 Maintenance When there is a problem with the lamp J The status of the indicator is displayed with the following symbols.
94 - ENGLISH Maintenance Replacement Before replacing the unit When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect z the power plug from the wall outlet. ( Æ pages 36, 40) Be sure to observe the procedure “T uring off the projector” ( z Æ page 40) when performing power supply operation.
Replacement ENGLISH - 95 Maintenance Pull out the air lter unit. When 4 ) taking out the air lter unit, put your nger on the air lter unit’ s tab and then pull. Put the new one back into the position 5 ) and close the lter cover . Make sure that the air lter unit is properly and fully inserted.
Replacement 96 - ENGLISH Maintenance J Lamp unit The lamp unit is a consumable component. Y ou can check the total usage time using Lamp runtime in the Information menu on page 72. It is recommended to ask an authorized engineer to replace the lamp unit.
Replacement ENGLISH - 97 Maintenance J Replacing the Lamp unit CAUTION: When the projector is mounted on a ceiling, do not work with your face close to the projector . z Attach the lamp unit and the lamp cover securely . z When you experience difculty in installing the lamp, remove it and try again.
98 - ENGLISH Maintenance T roubleshooting Please check following points. For details, see the corresponding pages. Problem Cause Reference page Power does not turn on. The power cord may not be connected. z — No electric supply is at the wall outlet.
T roubleshooting ENGLISH - 99 Maintenance Problem Cause Reference page The picture does not display correctly . There may be a problem with the VCR or other signal source. z A signal which is not compatible with the projector is being input. z — 109-1 13 Picture from a computer does not appear .
100 - ENGLISH Appendix T echnical Information PJLink protocol The net work func tion of the p rojector suppo r ts P JLink c lass 1 , and the P J Link protocol c an be used to per form projec tor setting and p rojector st atus quer y operations f rom a com puter .
T echnical Information Appendix ENGLISH - 101 Control commands via LAN When WEB Control administrator rights password is set (Protect mode) J Connection method z Obtain the IP address and port number (Initial set value = 1 024) of the projector and 1 ) make a request for connection to the projector .
T echnical Information 102 - ENGLISH Appendix When WEB Control a dministrator rights password is not set (Non-protect J mode) Connection method z Obtain the IP address and port number (Initial set value = 1 024) of the projector and 1 ) make a request for connection to the projector .
T echnical Information Appendix ENGLISH - 103 Serial terminal The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specication, so that the projector can be controlled by a personal computer which is connected to this connector .
T echnical Information 104 - ENGLISH Appendix J Basic format T ransmission from the computer begins with STX, then the command, parameter , and ETX are sent in this order . Add parameters according to the details of control. STX C1 C2 C3 : P1 P2 Pn ETX When sending commands without parameters, a colon (:) is not necessary .
T echnical Information Appendix ENGLISH - 105 J Cable specications [When connected to a computer] Projector 1 NC NC 1 Computer (DTE specications) 2 2 3 3 4 NC NC 4 5 5 6 NC NC 6 7 7 8 8 9 NC NC .
T echnical Information 106 - ENGLISH Appendix Other terminals Pin assignments and signal names of <S-VIDEO IN> terminal J Outside view Pin No. Signal names GND (luminance signal) GND (color signal) Luminance signal Color signal Pin assignments and signal names of <RGB> terminal J Outside view Pin No.
T echnical Information Appendix ENGLISH - 107 Pin assignments and signal names of <DVI-D> terminal J Outside view Pin No. Pin No. Signal names 1 T .M.D.S. Data2– 15 Ground (for +5V) 2 T .M.D.S. Data2+ 16 Hot Plug Detect 3 T .M.D.S. Data2 Shield 17 T .
T echnical Information 108 - ENGLISH Appendix List of Picture in Picture o : Picture in Picture combinations are enabled. x : Picture in Picture combinations are disabled Note When the input signal(s) is/are incompatible, z X mark will be displayed on the Main/Sub picture .
T echnical Information Appendix ENGLISH - 109 List of compatible signals The following table species the types of signals compatible with the projectors.
T echnical Information 1 10 - ENGLISH Appendix Mode Display resolution * 1 (dots) Scanning frequency Dot clock frequency (MHz) Picture quality * 2 PnP* 3 Format H (kHz) V (Hz) EW630 series EW530 series EX600 series EX500 series EZ570 series SVGA 800 x 600 38.
T echnical Information Appendix ENGLISH - 111 Mode Display resolution * 1 (dots) Scanning frequency Dot clock frequency (MHz) Picture quality * 2 PnP* 3 Format H (kHz) V (Hz) EW630 series EW530 series EX600 series EX500 series EZ570 series WXGA 1 280 x 800 49.
T echnical Information 1 12 - ENGLISH Appendix Mode Display resolution * 1 (dots) Scanning frequency Dot clock frequency (MHz) Picture quality * 2 PnP* 3 Format H (kHz) V (Hz) EW630 series EW530 series EX600 series EX500 series EZ570 series D-VGA 640 x 480 31.
T echnical Information Appendix ENGLISH - 1 13 “i” added to the resolution value indicates an interlaced signal. *1 : Picture quality is indicated by the following symbols. *2 : AA: Maximum picture quality can be obtained. A: Signals are converted by the image processing circuit.
1 14 - ENGLISH Appendix Specications Model No. EW530 series EW630 series EX500 series EX600 series EZ570 series Power supply AC100 V - 240 V 50 Hz/60 Hz Power consumption 100 V - 240 V 4.9 A-2.0 A 490 W When [Standby mode] of [Setting] is set to [ECO]: 0.
Specications Appendix ENGLISH - 1 15 Model No. EW530 series EW630 series EX500 series EX600 series EZ570 series T erminals MONITOR OUT 1 (D-sub 15 pin female) [RGB signal] 0.
1 16 - ENGLISH Appendix Dimensions <Unit : mm(inch)> Ceiling mount bracket safeguards Installation work of the ceiling mount bracket should only be carried by a qualied technician.
Appendix ENGLISH - 1 17 Index A About Y our Projector....................... 19 Accessing from the Web browser ... 76 Accessories .................................... 17 Adjusting front adjustable feet ........ 34 Adjusting the image .................
Panasonic Systems Communications Company of North America 3 Panasonic Way, Secaucus, NJ 07094 TEL: (877) 803 - 8492 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 TEL: (905) 624 - 5010 Panasonic Corporation © Panasonic Corporation 2012 We b Site : http://panasonic.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Panasonic PT-EX500UL c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Panasonic PT-EX500UL - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Panasonic PT-EX500UL, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Panasonic PT-EX500UL va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Panasonic PT-EX500UL, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Panasonic PT-EX500UL.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Panasonic PT-EX500UL. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Panasonic PT-EX500UL ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
