Manuel d'utilisation / d'entretien du produit AJ-D440 du fabricant Panasonic
Aller à la page of 68
.
IMPORTANT “Unauthorized recording of copyrighted televi- sion programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws.” CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
– 3 – Contents General and Features Controls and their functions • Front panel • Connector area Tapes Connections • When recording/playback using 1 unit • When recording, playback and edit.
– 4 – General and Features This unit is a digital video cassette recorder which uses 1/4-inch tapes. It incorporates digital compression technology so that the deterioration in picture quality and sound quality resulting from dubbing is significantly minimized compared with existing analog systems.
– 5 – Multi-function input/output interfaces (AJ-D450 only for input) • Analog input/output Component (Y, P B , P R ) and composite and S-VIDEO signal input and output connectors are provided. • Digital audio input/output AES/EBU audio input/output is possible when the optional digital audio interface board (AJ- YA655P) is used.
– 6 – Controls and their functions Front panel Counter Display Section ON OFF POWER EJECT REC PLAY FF STOP REW COUNTER/ REMAIN RESET CH CONDITION LEVEL HEADPHONES CH 1 AUDIO REC LEVEL CTL TC UB CH.
– 7 – POWER switch When the ON side is pressed, the power is switched on, and the counter display lights up. Cassette insertion slot The M cassette, L cassette and consumer cassette (S cassette) with adaptor are inserted into this slot. Consumer cassettes can be played back only.
.
– 9 – Headphones jack The sound being recorded, played back or edited can be monitored on stereo headphones when they are connected to this jack. Volume control This is used to adjust the headphones volume. Audio recording level controls (AJ-D450 only) These are used to adjust the recording levels of the analog audio signal CH1/CH2.
– 10 – Controls and their functions (continued) SET button When this is pressed, the data which has been set on the setup menu is entered. After data entry, the setup mode is exited and the original operating mode is restored. DIAG button When this is pressed, VTR information is displayed.
– 11 – Connector area * Applicable only to AJ-D450..
– 12 – AC IN connector This is for connecting the unit to the power outlet using the power cord provided. SIGNAL GND terminal This terminal is connected to the signa unit which is connected to the unit in order to reduce noise. It is not connected to ground for safety purposes.
– 13 – S1-VIDEO OUT connector This is the S-VIDEO output connector. ANALOG COMPONENT VIDEO OUT connector The analog component video signal is output from this connector. ANALOG COMPOSITE VIDEO OUT connectors The analog composite video signals are output from these connectors.
Tapes Type Description Consumer cassette (S cassette) M cassette L cassette Tape designed exclusively for the camcorders used by consumers in general. Only playback is possible using the optional cassette adaptor (AJ-CS750P). However, please note that long-play cassette tapes (80- minute standard/120-minute LP mode) cannot be used.
– 15 – When recording/playback using 1 unit.
– 16 – When recording, playback & editing with 2 units (deck to deck).
– 17 – When using an editing controller Basic system Camera/external input editing System using two players (AB roll editing) Video/audio signals Remote Remote Player Recorder Recorder AJ-D440 AJ-.
– 18 – Internal encoder adjustments In order to ensure error-free and accurate editing during AB roll editing (a method of editing using two source VTRs) using an editor, the ENCODER OUT controls must be adjusted after the system has been connected.
– 19 – Check the connections. (see previous page.) Select [OFF] on ENCODER SEL at the set up menu. (See page 30.) Select [ON] to operate the internal encoder externally. Adjust the SYSTEM PHASE. 3-1 3-2 1 2 Adjust the connected P2 VTR in the same way.
– 20 – Printed circuit board Printed circuit board F8 board ADDA- CUE* SW1 Audio Input Impedance SW SW61 HIGH This sets the CH1 audio input impedance. HIGH/600 Ω HIGH SW400 BETA Abbr. name Full name Function Factory setting F4 board Audio Input Impedance SW Component P B /P R Output level selector This sets the CH2 audio input impedance.
– 21 – Switching on the power/inserting the cassette Before starting to operate the unit, check whether the equipment has been connected properly. Turn on the power. Check that the error indicator is not displayed on the counter. Insert the cassette tape.
– 22 – STOP mode When the STOP button is pressed, the unit goes into the stop mode. The STOP lamp lights and the tape stops traveling. • In order to protect the tape, the unit goes into the standby OFF mode after the time set by setup menu No. 400 (STILL TIMER) has elapsed.
– 23 – Recording (AJ-D450 only) Set the accidental erasure prevention tab on the cassette tape to the “recording” position and insert the tape. Press the STOP button to place the unit in the stop mode. Check that the REC INHIBIT lamp is off. Select the video and audio input signals and adjust their levels.
– 24 – Playback Insert the cassette tape, and place the unit in the stop mode. Press the PLAY button. Regular playback is now commenced. To end playback, press the STOP button. The VTR now goes into the stop mode. 1 2 <Note> Check that the SERVO lamp is lighted during playback.
– 25 – Setup (default settings) The unit’s major settings are performed by making selections on menus. The setting menus appear on the TV monitor when the TV monitor and VIDEO OUT 3 connector in the unit's connector area are hooked up.
– 26 – Setup (setting) menus 1 2 3 This unit can store up to 5 user files (user 1 to user 5) containing different menu settings, and these files can be selected and used. Changing the file Press the MENU button. Hold down the FILE button and press the cursor button to switch to the next user file.
– 27 – Setup menus Lock mode can be set to protect the settings in the system files and user files (USER2 – USER5). Settings can no longer be changed when this mode is set. To set and release the lock mode for the system files and user files use setup item No.
– 28 – Setup menus The contents of the USER2 – USER5 files can be copied (loaded) into the USER1 file. In addition, the contents of the USER1 file can be copied (saved) to the USER2 – USER5 files. USER1 USER2 USER3 USER4 USER5 Settings can be locked.
– 29 – Saving a user file Automatic loading of user file when the power is turned on When the user file to be loaded is selected in advance using setup menu item No. A02 (P.ON LOAD), it can be automatically loaded into USER1 when the power is turned on.
.
– 31 – Setup menus The underline on the setting item denotes the initial setting. Item Setting No. Superimposed display Description No. Superimposed display USER menu 002 CHARA V-POS 003 DISPLAY SEL 0000 0001 0002 TIME T&STA T&S&M 005 TAPE TIMER 0000 0001 ± 12h 24h 0000 0018 0022 0 18 22 .
– 32 – Setup menus.
– 33 – The underline on the setting item denotes the initial setting. * The Setup menu can only be displayed for the model AJ-D450. Item Setting No.
– 34 – Setup menus USER menu The underline on the setting item denotes the initial setting. Item Setting No. Superimposed display Description No. Superimposed display 201 9P SEL 0000 0001 OFF ON This selects whether the 9P connector functions when the REMOTE/LOCAL switch has been set to REMOTE.
– 35 – The underline on the setting item denotes the initial setting. * The Setup menu can only be displayed for the model AJ-D450. Item Setting No.
– 36 – Setup menus.
– 37 – The underline on the setting item denotes the initial setting. <TAPE PROTECT> <Note> In order to protect the tape and VTR helical heads, it is recommended that the Still Timer be set for automatic tape protection mode in 30 seconds or under.
– 38 – Setup menus USER menu.
– 39 – Item Setting No. Superimposed display Description No. Superimposed display USER menu 508* TCG CF FLAG 0000 0001 OFF ON This selects whether the CF flag of the TCG is to ON. 0: 1: CF flag is OFF. CF flag is ON. 507 PHASE CORR 0000 0001 OFF ON This selects whether to control the phase correction of the LTC generated by the TCG.
– 40 – Setup menus The underline on the setting item denotes the initial setting. USER menu 611 EDH 0000 0001 OFF ON This selects whether to superimpose EDH onto the serial output signals. 0: 1: • This item setting is valid when the optional serial interface board has been installed.
– 41 – The underline on the setting item denotes the initial setting. * The Setup menu can only be displayed for the model AJ-D450. USER menu <AUDIO>.
– 42 – Setup menus The underline on the setting item denotes the initial setting. * The Setup menu can only be displayed for the model AJ-D450. Item Setting No.
– 43 – The underline on the setting item denotes the initial setting. Item Setting No. Superimposed display Description No. Superimposed display <MENU> A00 LOAD 0000 0001 0002 0003 USER2 USER3 USER4 USER5 This selects the user file whose contents will be loaded into USER1.
– 44 – Time code/user bit The time code is used when the time code signal generated by the time code generator (time code signal generator) is to be recorded on the tape, its values are to be read.
– 45 – Recording internal/external time codes Place the VTR in the stop mode. Set the CTL/TC/UB switch to TC. Set the TC INT/EXT switch to INT. (Internal time code selected) Set the RUN MODE. (setup menu No. 510) REC (RUN): FREE (RUN): Set the REGEN MODE.
– 46 – Reproducing the time code/user bit Place the unit in the stop mode. Set the CTL/TC/UB switch to TC or UB. TC: UB: Press the PLAY button. Playback now commences, and the time code appears on the display. When setup menu No.006 (SUPER) is ON, the time code value is superimposed onto the video signal from the VIDEO OUT 3 connector.
– 47 – Superimpose screen.
– 48 – Servo reference EXT This unit automatically selects the input video signal selected by the INPUT switch, the reference video signal supplied from the REF VIDEO input connector or the internal sync signal as the servo reference signal.
– 49 – Servo reference setting tables .
– 50 – Audio V Fade Function (AJ-D450 only) When editing tapes, the edit point splicing selection (setup menu No. 309 and 310) information is recorded on the tape. This information is then sensed during playback, and V fade or cut processing is automatically performed for these sections.
Rack mounting The unit can be mounted into a 19-inch standard rack if the optional rack-mounting adaptors (AJ-MA75P) are used. For the installation rails, it is recommended that the rail and bracket for 18" length (model number CC3001-99-0400) of CHASSIS TRAK be used.
– 52 – Video head cleaning This unit has an auto head cleaning function which automatically reduces the dirt on the heads. However, to further increase the unit’s reliability, it is recommended that its video heads be cleaned every day. Use the cleaning fluid designated by Panasonic.
– 53 – Error messages When a warning occurs in this unit, an error number appears at the counter display. Opening the DIAG menu will display the error description on the monitor. Also, when an abnormal operation is detected in this unit, an error number flashes on the counter display.
– 54 – Error messages.
– 55 –.
– 56 – Error messages.
– 57 – RS-232C interface The VTR can be operated by commands when the RS-232C interface is used. (See command table on page 60 – 62.) Conditions for acknowledging commands from RS-232C interface The front panel REMOTE/LOCAL switch must be at REMOTE.
– 58 – RS-232C interface.
– 59 –.
– 60 – RS-232C interface.
– 61 –.
– 62 – Commands relating to inquiries (2) VTR operation Send command Return (completion) message Supplementary notes [STX] QCD [ETX] <Notes> • • As for the return (completion) message, [ACK] is first returned when data is received, and the execution message is subsequently returned.
– 63 – Microsoft QuickBASIC sample program (3) CLS STX$ = CHR$(&H2): ETX$ = CHR$ (&H3): NAK$ = CHR$(15): ACK$ = CHR$(&H6) PRINT "*** RS-232C COMMUNICATION SAMPLE PROGRAM ***" PRINT "Type Command 'QUIT' to quit.
– 64 – Connector signals.
– 65 – RS-232C REMOTE (25-pin D-SUB straight cable supported) Pin No. 1 FRAME GROUND Abbreviation Circuit Description Protective ground ENCODER REMOTE (15P) Pin No. Pin No. 1 Signal Signal Pin No. Signal 61 1 2 SET UP 7 12 3 C LEVEL 8 13 4 GND 9 HUE –12V SYSTEM H SYS.
– 66 – Specifications GENERAL Operating ambient temperature: Operating ambient humidity: Weight: Dimensions (W × H × D): Recording format: Recording tracks: Tape speed: Recording time: Tape: FF/.
– 67 –.
PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500 EASTERN ZONE: One.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Panasonic AJ-D440 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Panasonic AJ-D440 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Panasonic AJ-D440, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Panasonic AJ-D440 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Panasonic AJ-D440, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Panasonic AJ-D440.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Panasonic AJ-D440. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Panasonic AJ-D440 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
