Manuel d'utilisation / d'entretien du produit Digital Tuner Output Projector du fabricant Optoma Technology
Aller à la page of 31
1 ... English Table of Contents T able of Contents ....................................................................................... 1 Usage Notice .............................................................................................. 2 Precautions .
2 English ... Usage Notice Precautions Follow all warnings, precautions and maintenance as recom- mended in this user’s guide to maximize the life of your unit. Warning- Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes.
3 ... English Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don’t: Block the slots and openings on the unit provided for ventilation.
4 English ... Product Features This product is an SVGA single chip 0.55” DLP TM projector. Outstanding features include: True SVGA, 800 x 600 addressable pixels Single chip DLP TM technology NTSC/NTSC4.
5 ... English Power Cord 1.8m VGA Cable 1.8m Remote Control 2 x Battery Introduction Composite Video Cable 1.8m Projector with lens cap Package Overview This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing.
6 English ... Main Unit Product Overview 1. Focus Ring 2. Zoom Ring 3. Elevator Button 4. Zoom Lens 5. Remote Control Receiver 6. Connection Ports 7. Power Connector 8.
7 ... English Control Panel 1. Temp Indicator LED 2. Lamp Indicator LED 3. Power/Standby 4. Source 5. Four Directional Select Keys 6. Enter 7 4 8 5 Connection Ports 1. Remote Control Receiver 2. PC Analog Signal/HDTV/ Component Video Input Connector 3.
8 English ... Remote Control Introduction 1 6 9 11 2 3 1. Transmit Indicator Light 2. Power 3. Re-Sync 4. Volume ( + / - ) 5. Reset 6. Mute 7. Freeze 8. Page Up / Page Down 9. Keystone Correction 10. Menu 11. Four Directional Select Keys 4 7 8 10 5 12 14 13 15 12.
9 ... English 1 . Power Cord 2 . VGA Cable 3 . Composite Video Cable 4 . Audio Cable Jack/RCA (Optional Accessory) 5 . S-Video Cable (Optional Accessory) 6 .
10 English ... Installation Power/ Standby 1 2 Powering On the Projector 1. Remove the lens cap. n 2. Ensure that the power cord and signal cable are securely connected. The “Power/Standby” button will flash green . 3. Turn on the lamp by pressing “Power/Standby” button on the control panel.
11 ... English Powering Off the Projector 1. Press the “Power/Standby” button to turn off the projector lamp, you will see a message “Power off the lamp?” on the on-screen display. 2. Press the “Power/Standby” button again to confirm. Otherwise the message will disappear after 5 seconds.
12 English ... Adjusting the Projected Image Adjusting the Projector Image Height Tilt Adjusting Wheel Elevator Foot 1 2 3 Elevator Button The projector is equipped with an elevator foot for adjusting the image height. To raise the image: 1. Press the elevator button n .
13 ... English Max. 39.4"(100. 0cm) 84.4"(214. 3cm) 140.6"(357 .1cm) 225. 0"(571.4cm) 281.2"( 714.3cm) 337.5"(857 .1cm) Min. 32.5"(82. 5cm) 69.6"(176. 9cm) 116. 1"(294.8cm) 185.7"(471 .7cm) 232.1"( 589.
14 English ... User Controls Remote Control Control Panel Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Using the Control Panel Power/Standby Refer to the “Power On/Off the Projector” section on pages 10-11.
15 ... English Using the Remote Control Power/Standby Refer to the “Power On/Off the Projector” section on pages 10-11. Re-Sync Automatically synchronizes the projector to the input source. Volume + / - Increases/decreases speaker volume.
16 English ... The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press “Menu” on the Remote Control or Control Panel.
17 ... English Language Language Choose the multilingual OSD menu . Use the or key to select your prefered language. Press “Enter” to finalize the selection.
18 English ... Image-I Brightness Adjust the brightness of the image. Press the to darken image. Press the to lighten the image. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
19 ... English Image-II (Computer Mode) Frequency “Frequency”changes the display data frequency to match the frequency of your computer’s graphic card. If you experience a vertical flickering bar, use this function to make an adjustment. Tracking “Tracking” synchronizes the signal timing of the display with the graphic card.
20 English ... Reset Choose “Yes” to return the display parameters (except for Lamp Hour) on all menus to their factory default settings. Image-II (Computer Mode) Computer Mode User Controls.
21 ... English Image-II (Video Mode) Video Mode Degamma This allows to you to choose a degamma table that has been fine- tuned to bring out the best image quality for the input. Saturation Adjusts a video image from black and white to fully saturated color.
22 English ... Reset Choose “Yes” to return the display parameters (except for Lamp Hour) on all menus to their factory default settings. Image-II (Video Mode) Video Mode User Controls.
23 ... English Audio Volume Press the to decrease the volume. Press the to increase the volume. Treble The treble setting controls the higher frequencies of your audio source. Press the to decrease the treble. Press the to increase the treble.
24 English ... Menu Location Choose the Menu location on the display screen. Projection Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project behind a translucent screen.
25 ... English Management Computer / Video Mode Lamp Reminding Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will show up 30 hours before end of life. ECO Mode Choose “On” to dim the projector lamp which will lower power consumption and extend the lamp life by up to 130%.
26 English ... Appendices Problem: No image appears on screen. Ensure all the cables and power connections are correctly and securely connected as described in the “Installation” section. Ensure the pins of connectors are not crooked or broken.
27 ... English 6. Click on “Show all devices”. Then select “Standard monitor types” under the “Manufacturers” box ; choose the resolution mode you need under the “Models” box. 7. Verify that the resolution setting of the monitor display is less than or equal to 800 x 600.
28 English ... Problem: The image is outstretched when displaying 16:9 DVD. The projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting.
29 ... English Replacing the lamp The projector will detect the lamp life itself. It will show you a warning message “Lamp may fail soon ! Replacement Suggested !” When you see this message, change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp.
30 English ... Specifications Light Valve - Single Chip DLP TM Technology by Texas Instruments Lamp - 200W User Replaceable Lamp Number of Pixels - 800 pixels(H) X 600 lines(V) Displayable Color - 16.7M colors Projection Lens - F/2.4~2.7 f=19.7~23.6mm with 1.
31 ... English VES A V GA 640 X 350 70 31.5 VES A V GA 640 X 350 85 37.9 VES A V GA 640 X 400 85 37.9 VES A V GA 640 X 480 60 31.5 VES A V GA 640 X 480 72 37.9 VES A V GA 640 X 480 75 37.5 VES A V GA 640 X 480 85 43.3 VES A V GA 720 X 400 70 31.5 VES A V GA 720 X 400 85 37.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Optoma Technology Digital Tuner Output Projector c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Optoma Technology Digital Tuner Output Projector - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Optoma Technology Digital Tuner Output Projector, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Optoma Technology Digital Tuner Output Projector va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Optoma Technology Digital Tuner Output Projector, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Optoma Technology Digital Tuner Output Projector.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Optoma Technology Digital Tuner Output Projector. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Optoma Technology Digital Tuner Output Projector ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
