FR
Olympus logo
Notice d'utilisation officielle

Olympus PPO-E05

60 pages·7.9 MB·Objectif photo·PDF·ENITNL
Olympus PPO-E05
Table des matières 12 sections Introduction · Please read the following items before use · For safe use · WARNING · … AfficherMasquer
Page 1 of the Olympus PPO-E05 user manual — WARNING
Page 1 · cliquer pour agrandir
Page 1
Olympus PPO-E05 — Introduction diagram (page 1)
Fig. 1 · Introduction

„ Thank you for buying this product. To assure safe and correct use of this product, please read this

instruction manual carefully. After reading, store the manual together with the warranty card in a safe, easily accessible place. „ This product is the Waterproof Lens Port (PPO-E05) designed exclusively for use with the PT-E

series of waterproof case. „ Underwater zooming is made possible by attaching the zoom gear, provided with this product, to

Introduction

„ Unauthorized copying of this manual in part or in full, except for personal use, is prohibited.

Unauthorized reproduction is strictly prohibited. „ Olympus shall not be responsible for damages, loss of profit or any claims by third parties in case of

any damage occurring from incorrect use of this product.

Please read the following items before use

„ This product has been designed to be used underwater at depths up to 40 meters. Handle this product

with care. „ This product must always be used in combination with an applicable lens. Do not combine this product

with an inapplicable lens. „ To ensure correct and safe use of this product, always use it as described in this instruction manual.

For safe use

This instruction manual uses pictographs to show how to use the product correctly and how to prevent danger to the user and other persons as well as damage to property. These pictographs and their meanings are shown below.

WARNINGPlease pay particular attention to this information. If ignored when using the product, there is a risk of serious injury and even death. CAUTIONIgnoring this information when using the product could lead to injury or material damage.

WARNING

z This product should be kept out of reach of infants and children to prevent accidents such as the

  • following:
  • Injury caused by the product falling from a height and striking the body.
  • Injury caused by the swallowing of small parts. Please consult a doctor immediately if this happens. z This product is partly made of glass. If it is broken or smashed by being dropped or hit against a hard

object, glass splinters could cause injury. Handle this product with care. z If water gets into this product during underwater use, immediately stop using it, remove the moisture

from the product and detach it from the camera and lens. z Do not disassemble or modify this product. This may result in injury. z The silicone O-ring grease is inedible.

Page 2 of the Olympus PPO-E05 user manual — 1. Name of Parts
Page 2 · cliquer pour agrandir
Page 2

CAUTION

z Do not expose this product to high temperatures for extended periods. This may lead to deterioration

of the product’s components. z When mounting this product on the PT-E series waterproof case, be sure to follow the steps described

in this manual. z Before detaching this product from the PT-E series waterproof case, make sure that the case is

completely dry and free of moisture. z Never attach or detach this product in locations where there is a lot of sand, dust or dirt. If any foreign

matter gets on the O-ring sections, the waterproof sealing will be compromised and water leakage may result. z This product has been designed to be used underwater at depths up to 40 meters. Please note that

diving in depths over 40 meters may cause irreparable damage and/or may result in water leaking into this product and the camera and lens. z The maximum depth that this product can be used is 40 meters, regardless of what case it is combined

with. For example, even when combined with a PT-E series case certified for 60 meters, the maximum depth is still limited to 40 meters. z When sealing this product, make sure that no foreign matter is caught on the O-rings or O-ring contact

surfaces. z Before storing this product, always remove it from the camera and lens. z To control lens zooming from this product, the provided zoom gear must be attached to the zoom ring

of the lens. Correctly attach the zoom gear to the zoom ring of the lens as instructed in this manual.

1. Name of Parts

Olympus PPO-E05 — 1. Name of Parts diagram (page 2)
Fig. 2 · 1. Name of Parts

1 PPO-E05 main body 2 Silicon O-ring (POL-E101) 3 Front cap 4 Rear cap 5 Zoom gear (PPZR-E06) 6 Grease for silicone O-ring 7 O-ring remover

Page 3 of the Olympus PPO-E05 user manual — 2. Mounting the PPO-E05 on the Waterproof Case
Page 3 · cliquer pour agrandir
Page 3

2. Mounting the PPO-E05 on the Waterproof Case

This section describes how to mount this product on the PT-E series case. Before mounting, check that no foreign matter is attached to the O-rings, the port mount thread on the PT-E series case, or the O- ring contact surfaces. Apply a thin layer of the provided silicone O-ring grease.

Olympus PPO-E05 — 2. Mounting the PPO-E05 on the Waterproof Case diagram (page 3)
Fig. 3 · 2. Mounting the PPO-E05 on the Waterproof Case

1 Align the threaded section of the PPO-E05 with the port mount thread on the PT-E series case.

2 Hold the PT-E series case firmly with one hand, hold the main body of the PPO-E05 with your other hand and screw it into the PT-E series by turning the PPO-E05 clockwise.

3 Resistance increases as the PPO- E05 is screwed in more deeply. However, be sure to screw it in all the way until there is no gap visible below the threaded section of the PPO-E05.

Screw in until there

is no gap.

Page 4 of the Olympus PPO-E05 user manual — 3. Dismounting the PPO-E05
Page 4 · cliquer pour agrandir
Page 4

3. Dismounting the PPO-E05

Olympus PPO-E05 — 3. Dismounting the PPO-E05 diagram (page 4)
Fig. 4 · 3. Dismounting the PPO-E05

1 If any water is on the product, wipe it completely away and make sure that the product is dry.

2 Holding the PT-E series case firmly with one hand, loosen the PPO-E05 by turning it about 90 degrees counterclockwise. If the PPO-E05 is attached too tightly to turn, wrap it with a piece of rubber or similar non-slip material, and turn it counterclockwise.

Olympus PPO-E05 — 3. Dismounting the PPO-E05 diagram (page 4)
Fig. 5 · 3. Dismounting the PPO-E05

3 After loosening the PPO-E05, point its lens downward and turn it further counterclockwise until it is separated from the PT-E series case. Be careful not to drop the PPO-E05 or PT-E series case.

  • CAUTION:
  • While dismounting the PPOE05 from the case, water remaining on the PPO-E05 may splatter on the lens or camera. If this happens, wipe the water off the lens and camera with a dry cloth.
  • Make sure that the port is completely dry before dismounting.
Page 5 of the Olympus PPO-E05 user manual — 4. Attaching the Zoom Gear to the Lens
Page 5 · cliquer pour agrandir
Page 5

4. Attaching the Zoom Gear to the Lens

To use this product for lens zooming, attach the zoom gear provided with this product to the zoom ring of the lens.

1 The zoom gear has two marks (U) for use in aligning its position on the lens. Use either mark to adjust the position of the zoom gear with respect to the lens.

Olympus PPO-E05 — 4. Attaching the Zoom Gear to the Lens diagram (page 5)
Fig. 6 · 4. Attaching the Zoom Gear to the Lens

2 Turn the lens’ zoom ring to full wide-angle end and align the “14 mm” position with the index.

3 Attach the zoom gear to the lens from the direction of the lens mount. Be sure to attach the zoom gear in the correct orientation.

4 Adjust the position of the zoom gear so that its front end is aligned with the front end of the lens’ zoom ring and the alignment mark (U) on the zoom gear is aligned with the mounting index on the lens.

Olympus PPO-E05 — 4. Attaching the Zoom Gear to the Lens diagram (page 5)
Fig. 7 · 4. Attaching the Zoom Gear to the Lens

5 Mount the lens/zoom gear combination on the lens.

  • CAUTION:
  • If the zoom gear position in the rotation and/or front-rear directions is inappropriate, the lens cannot be zoomed smoothly. Be sure to attach the zoom gear properly and ensure that it is correctly positioned.
  • For details on how to load the camera into the PT-E series case, refer to the case’s instruction manual.

UAlignment markings

Page 6 of the Olympus PPO-E05 user manual — 5. Maintenance
Page 6 · cliquer pour agrandir
Page 6

5. Maintenance

For safe use of this product, always perform maintenance after each diving session. For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series case instruction manual. Apply the same procedures to this product.

Olympus PPO-E05 — 5. Maintenance diagram (page 6)
Fig. 8 · 5. Maintenance
Olympus PPO-E05 — 5. Maintenance diagram (page 6)
Fig. 9 · 5. Maintenance

1 After shooting, remove the inserted camera and lens, then re-seal the empty case and immerse it in tap water to remove any salt as soon as possible.

2 After making sure that the PT-E series case is completely dry, dismount this product from the case.

3 Insert the O-ring remover between the O-ring and O-ring groove so that the tip of the O-ring remover slides under the O-ring (take care not to damage the groove with the tip of the O-ring remover). When the O-ring is raised, pinch it with your fingers and separate it from the case.

4 Remove any dust that you can see from the O-ring, and then pinch the O-ring with your fingers and rub it along its length to check for foreign objects such as sand, damage and cracks.

Olympus PPO-E05 — 5. Maintenance diagram (page 6)
Fig. 10 · 5. Maintenance

5 If any foreign matter is attached to the O-ring grooves, remove it using a clean, lint-free cloth or cotton swab. Also remove any foreign matter from the O-ring contact surfaces and from the port mount thread on the PT-E series case.

6 After removing foreign matter, apply the provided grease to the O-rings and fit them into the O-ring grooves. To apply grease to each O-ring, squeeze a drop of grease about the size of a grain onto your finger and lightly rub the entire circumference of the O-ring to spread the grease thinly and evenly.

Page 7 of the Olympus PPO-E05 user manual — 7. Consumable Items
Page 7 · cliquer pour agrandir
Page 7

6. Specifications

Applicable case : PT- E series Applicable lens : ZUIKO DIGITAL ED14-42 mm F3.5-5.6 Main materials Main body : Aluminum. Lens window : Chemically reinforced glass. O-rings : Silicon rubber. Zoom gear : NBR rubber. Front cap : NBR rubber. Rear cap : Polyethylene resin. Withstanding pressure : Water depth of 40 m Dimensions : Max. diameter 143 mm x Depth 80 mm Weight : 739 g (excluding the conversion lens)

7. Consumable Items

This product uses the following consumable items.

POL-E101 O-ring for use with the PT-E series case.

„ Grease for silicone O-ring

PSOLG-1 Grease for silicone O-ring

„ Silicon O-rings · Product Model Description · Product Model Description

Page 8 of the Olympus PPO-E05 user manual — 6. Specifications
Page 8 · cliquer pour agrandir
Page 8
Olympus PPO-E05 — 6. Specifications diagram (page 8)
Fig. 11 · 6. Specifications
Olympus PPO-E05 — 6. Specifications diagram (page 8)
Fig. 12 · 6. Specifications
Olympus PPO-E05 — 6. Specifications diagram (page 8)
Fig. 13 · 6. Specifications

Poser une question sur : Olympus PPO-E05

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Olympus PPO-E05

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Olympus PPO-E05 manuel PDF

60 pages·7.9 MB·Objectif photo·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…