
tion manual carefully. After reading, store the manual together with the warranty card in a safe, easily accessible place. ■ This product is the Waterproof Lens Port (PPO-E04) designed exclusively for use with the PT-E series of
waterproof case. ■ This product (PPO-E04) is an underwater lens port for use with the ZUIKO DIGITAL ED 7-14mm or ED
8mm Fisheye lens. When used with the ED 7-14mm lens, the PPO-E04 should also be used in combina- tion with the PER-E02 Underwater Extension Ring.
reproduction is strictly prohibited. ■ Olympus shall not be responsible for damages, loss of profit or any claims by third parties in case of any
damage occurring from incorrect use of this product.
product with care. ■ This product must always be used in combination with an applicable lens. Do not combine this product
with an inapplicable lens. ■ When this product is used with the ZUIKO DIGITAL ED 7-14mm lens, the separately available PER-E02
Underwater Extension Ring must also be used. ■ To ensure correct and safe use of this product, always use it as described in this instruction manual.
This instruction manual uses pictographs to show how to use the product correctly and how to prevent danger to the user and other persons as well as damage to property. These pictographs and their meanings are shown below.
Please pay particular attention to this information. If ignored when using the product, there is a risk of serious injury and even death. WARNING
Ignoring this information when using the product could lead to injury or material damage. CAUTION


PPO-E04 main body Silicon O-ring (POL-E101) Front cap Rear cap Lens hood Grease for silicone O-ring Pick for O-ring removal Lens hood clamping screws (x 4) Clamping screw securing wrench
This chapter describes how to mount this product and an applicable lens on the PT-E series Underwater Case. Before mounting, make sure that no foreign matter is attached to the PPO-E04’s O-ring and thread- ed section or to the case’s port mount thread and O-ring contact surface. Apply a thin layer of the provided silicone O-ring grease to each of these parts.

Align the threaded section of the PPO-E04 with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the lens hood around the lens of the PPO-E04 with
your other hand and screw it into the PT-E series by turning the PPO-E04 clockwise. Resistance increases as the PPO-E04 is screwed in more deeply. However, be sure to screw it in all the way
until there is no gap visible between the case’s port mount thread and the PPO-E04’s threaded section. If the resistance is extremely high, apply some more silicone O-ring grease again to surfaces listed above.



"
! " # $
When using the ZUIKO DIGITAL ED 7-14 mm lens, the separately available PER-E02 Underwater Extension Ring should be mounted between the PPO-E04 and PT-E series Underwater Case. Before mounting, make sure that no foreign matter is attached to the O-rings, O-ring contact surfaces, port mount threads and threaded sections of the three modules. After this, apply thin layers of the provided silicone O- ring grease on these parts.
Align the threaded section of the PER-E02 extension ring with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the main body of the PER-E02 extension ring with
your other hand and screw it into the PT-E series by turning the extension ring clockwise. Resistance increases as the PER-E02 extension ring is screwed in more deeply. However, be sure to screw it in all
the way until there is no gap visible between the case’s port mount thread and the extension ring’s threaded section. If the resistance is extremely high, apply some more silicone O-ring grease again to surfaces listed above.


Align the lens port mount thread of the PER-E02 extension ring with the threaded section on the PPO-E04. Hold the PT-E series case and PER-E02 extension ring firmly with one hand, hold the lens hood around
the lens of the PPO-E04 with your other hand and turn it clockwise to screw it into the extension ring. Resistance will increase as the PPO-E04 is screwed in. However, be sure to screw it in all the way until there
is no gap visible between the PPO-E04’s thread section and the extension ring’s port mount thread. If the resistance is extremely high, apply some more silicone O-ring grease again to surfaces listed above.



To attach the front cap, fit it into the front end (lens hood) of the PPO-E04 as shown below. The front cap can be removed by reversing the attaching procedure. Be sure to remove the front cap before shooting.
If the corners of the image in the pickup finder are cut off after the PPO-E04 is attached, adjust the lens hood position.
Using the clamping screw securing wrench provided with the PPO-E04, loosen the four lens hood clamping
screws on the PPO-E04. Adjust the hood until the image in the pickup finder is not cut off. Set the lens hood to the position where the image is not cut off. Tighten the lens hood clamping screws to clamp the lens hood in that position.
Turn the lens hood to adjust the position. Tighten screws to clamp the lens hood.

If any water is on the product, wipe it completely away and
make sure that the product is dry.
Holding the PT-E series case firmly with one hand, loosen the
PPO-E04 by turning it about 90 degrees counterclockwise. If the PPO-E04 is attached too tightly to turn, wrap it with a piece of rubber or similar non-slip material.
After loosening the PPO-E04, point its lens downward and
turn it further counterclockwise until it is separated from the PT-E series case. Be careful not to drop the PPO-E04 or PT-E series case.
splash on the lens or camera. If this happens, wipe the water drops away from the lens and camera with a dry cloth. ・Make sure that all of the parts are completely dry before dismounting.

If any water is on the product, wipe it completely away and
make sure that the product is dry.
Holding the PT-E series case firmly with one hand, loosen the
PPO-E04 from the PER-E02 extension ring by turning the PPO-E04 about 90 degrees counterclockwise. If the PPO-E04 is screwed in too tight, wrap it with a piece of rubber or other slip-resistant material.
After loosening the PPO-E04, position it so that its lens
points down and turn it further counterclockwise until it sepa- rates from the extension ring. Be careful not to drop the PPO-E04, PER-E02 extension ring or PT-E series case.
Holding the PT-E series case firmly with one hand, loosen the
PER-E02 by turning it about 90 degrees counterclockwise. If the PER-E02 is screwed in too tight, wrap it with a piece of rubber or other slip-resistant material.
After loosening the PER-E02, point its lens down and turn it
further counterclockwise until it is separated from the PT-E series case. Be careful not to drop the PER-E02 or PT-E.
water drops on the O-rings may splash on the lens or camera. If this happens, wipe the water drops away from the lens and camera with a dry cloth. ・Make sure that all of the parts are completely dry before dismounting.

To control zooming of the ZUIKO DIGITAL ED 7-14mm lens using the combination of the PPO-E04 with the PER-E02 Underwater Extension Ring, the zoom gear, provided with the extension ring, must be attached to the zoom ring on the lens.
Remove the lens from the camera.
Turn the lens’s zoom ring so that the
“10mm” mark is aligned with the zoom index.
Fit the zoom gear from the lens mount side
Position alignment mark Index
so that the position alignment mark (two marks are provided on the gear periphery and either can be selected for use as refer- ence in the position alignment operation) is aligned with the index on the lens.
Fit the zoom gear by aligning the mark with the index.
Confirm that the position alignment mark on
the zoom gear is aligned correctly with the index on the lens and that the zoom gear is attached properly.
Confirm alignment.
Two position alignment marks are provided
Two marks are provided on the zoom gear.
on the gear periphery. Either mark can be used as reference in the position alignment operation for zooming control.
sure to attach the zoom gear to the correct position.
To enable manual focusing of this lens, we are developing a separately available MF gear (to be released in early 2006) for attachment to the lens’s MF ring.
Lens · Zoom gear

The following description is applicable when the ZUIKO DIGITAL ED 7-14mm lens is used. After installing the lens on the camera and attaching the zoom gear provided with the PER-E02 extension ring, insert the camera into the PT-E series case on which the PER-E02 extension ring and PPO-E04 are mounted.


Screw the camera table provided with the PT-E
series case firmly into the bottom of the cam- era.
er. If a lens cap or filter is attached to the lens or the strap is attached to the camera, remove them as well.
Lift the PT- E series case’s power switch dial,
Confirm that the camera’s power switch is OFF.
mode dial knob and zoom dial, and turn the case’s camera table lock lever counterclock- wise to release the lock. Refer to the PT-E series case’s instruction manual for instructions of how to attach the hot shoe cable for the flash.
Align the “10 mm” zoom position with the zoom index of the lens and, while pulling out the zoom dial of the PT-E series case further, place the camera table (with camera attached) on the camera table mount on the inner side of the front lid of the PT-E series case.

After inserting the camera, turn the PT- E series
Push in the PT- E series case’s power switch
case’s camera table lock lever all the way clock- wise to lock the camera table. Then, push in the zoom dial on the case and engage it with the zoom gear attached to the lens. Turn the zoom dial to confirm that it can control zooming.
dial and mode dial knob. Turn the power switch dial and mode dial knob and confirm that they can control the camera power ON-OFF and mode switching. Connect the hot shoe mount section of the hot shoe cable that has been connected to the PT-E series case to the hot shoe of the camera.
Attach the rear lid of the PT- E series case and
lock the four buckles (two diagonally located buckles first, and then the other two diagonally located buckles). Underwater shooting is now possible.

For safe use of this product, always perform maintenance after each diving session. For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series case instruction manual. Apply the same procedures to this product.


era and lens, then re-seal the empty case and immerse it in tap water to remove any salt as soon as possible.
case is completely dry, dismount this product from the case.
Remove sand and dust from the O-rings.
using the provided pick for removing O-rings. Take care not to damage the O-rings.
Pinch each O-ring between your fingers and lightly rub the entire circumference to check for foreign matter, scratches and cracks.


If any foreign matter is attached to the
After removing foreign matter, apply the
O-ring grooves, remove it using a clean, lint-free cloth or cotton swab. Also remove any foreign matter from the O-ring contact surfaces and from the port mount thread on the PT-E series case.
provided grease to the O-rings and fit them into the O-ring grooves. To apply grease to each O-ring, squeeze a drop of grease about the size of a grain onto your finger and lightly rub the entire circumference of the O-ring to spread the grease thinly and evenly.

Applicable case : PT- E series Applicable lens : ZUIKO DIGITAL ED 7-14mm F4.0*, ED 8 mm F3.5 Fisheye
* The separately available PER-E02 Underwater Extension Ring is required. Main materials Main body : Aluminum. Lens : Glass dome lens (AR multi-coated) O-rings : Silicon rubber. Front cap : Neoprene Rear cap : Polyethylene resin. Withstanding pressure : Water depth of 60 m (200 ft) Dimensions : Max. diameter 176 mm x Depth 78 mm Weight : Approx. 935 g
This product uses the following consumable items.

Description O-ring for use with the PT-E series case.
Shinjuku Monolith, 3-1 Nishi Shinjuku 2-chome, Shinjuku-ku, Tokyo, Japan
Tel: +49 40-23 77 3-0 Fax: +49 40-23 07 61 Goods delivery : Bredowstrasse 20, 22113 Hamburg, Germany Letters : Postfach 10 49 08, 20034 Hamburg, Germany
European Technical Customer Support: Please visit our homepage http://www.olympus-europa.com or call our TOLL FREE NUMBER* : 00800 - 67 10 83 00
Two Corporate Center Drive, Po Box 9058, Melville, NY 11747-9058, U.S.A. Tel. 631-844-5000
Technical Support (USA) 24/7 online automated help: http://www.olympusamerica.com/support Phone customer support: Tel. 1-888-553-4448 (Toll-free)
for Austria, Belgium, Denmark, Finland, France, Germany, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom *Please note that some (mobile) phone services/ provider do not permit access or request an additional prefix to +800 numbers.
Our phone customer support is available from 8 am to 10 pm (Monday to Friday) ET E-Mail: distec@olympus.com Olympus software updates can be obtained at: http://www.olympus.com/digital/
For all not listed European Countries and in case that you can’t get connected to the above mentioned number please make use of the following CHARGED NUMBERS: +49 180 5 - 67 10 83 or +49 40 - 237 73 899 Our Technical Customer Support is available from 9am to 6pm MET (Monday to Friday)
© 2005 OLYMPUS IMAGING CORP.
Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.