FR
Olympus logo
Notice d'utilisation officielle

Olympus PPO-E02

60 pages·5.4 MB·Accessoires pour appareil photo·PDF·ENITNL
Olympus PPO-E02
Table des matières 10 sections Disclaimer · IMPORTANT - Please read the following before using the product · For safe use · WARNING · … AfficherMasquer
Page 1 of the Olympus PPO-E02 user manual — CAUTION
Page 1 · cliquer pour agrandir
Page 1
  • Thank you for buying this product. To assure safe and correct use of this product, please read this instruc-

tion manual carefully. After reading, store the manual together with the warranty card in a safe, easily accessible place. ■ This product is the Waterproof Lens Port (PPO-E02) designed exclusively for use with the PT-E series of

waterproof case. ■ Underwater zooming is made possible by attaching the zoom gear, provided with this product, to the zoom

ring of an applicable camera lens.

Disclaimer

  • Unauthorized copying of this manual in part or in full, except for personal use, is prohibited. Unauthorized

reproduction is strictly prohibited. ■ Olympus shall not be responsible for damages, loss of profit or any claims by third parties in case of any

damage occurring from incorrect use of this product.

IMPORTANT - Please read the following before using the product

  • This product has been designed to be used underwater at depths up to 60 meters (200 ft). Handle this

product with care. ■ This product must always be used in combination with an applicable lens. Do not combine this product

with an inapplicable lens. ■ To ensure correct and safe use of this product, always use it as described in this instruction manual.

For safe use

This instruction manual uses pictographs to show how to use the product correctly and how to prevent danger to the user and other persons as well as damage to property. These pictographs and their meanings are shown below.

WARNINGPlease pay particular attention to this information. If ignored when using the product, there is a risk of serious injury and even death. CAUTIONIgnoring this information when using the product could lead to injury or material damage.

WARNING

  • This product should be kept out of reach of infants and children to prevent accidents such as the following:
  • Injury caused by the product falling from a height and striking the body from a height.
  • Injury caused by the swallowing of small parts. Please consult a doctor immediately if this happens.
  • This product is partly made of glass. If it is broken or smashed by being dropped or hit against a hard object, glass splinters could cause injury. Please handle this product carefully.
  • If water gets into this product during underwater use, immediately stop using it, remove the moisture from the product and detach it from the camera and lens.
  • Do not disassemble or modify this product. This may result in injury.
  • The silicone O-ring grease is not edible.

CAUTION

  • Do not expose this product to high temperatures for extended periods. This may lead to deterioration of the product’s components.
  • When mounting this product on the PT-E series waterproof case, be sure to follow the steps described in this manual.
  • Before detaching this product from the PT-E series waterproof case, make sure that the case is completely dry and free of moisture.
  • Never attach or detach this product in locations where there is a lot of sand, dust or dirt. If any foreign matter gets on the O-ring sections, the waterproof sealing will be compromised and water leakage may result.
  • This product has been designed and manufactured for use in a water pressure equivalent to a depth of 60 meters (200 ft). Please note that diving in depths over 60 meters may cause irreparable damage and/or may result in water leaking into this product and the camera and lens.
  • When sealing this product, make sure that no foreign matter is caught on the O-rings or O-ring contact surfaces.
  • Before storing this product, always remove it from the camera and lens.
  • To control lens zooming from this product, the provided zoom gear must be attached to the zoom ring of the lens. Correctly attach the zoom gear to the zoom ring of the lens as instructed in this manual.
Page 2 of the Olympus PPO-E02 user manual — Disclaimer
Page 2 · cliquer pour agrandir
Page 2
Olympus PPO-E02 — Disclaimer diagram (page 2)
Fig. 1 · Disclaimer

PPO-E02 main body Silicon O-ring (POL-E101) Front cap Rear cap Zoom gear Grease for silicone O-ring Pick for O-ring removal

This section describes how to mount this product on the PT-E series case. Before mounting, check that no for- eign matter is attached to the O-rings, the port mount thread on the PT-E series case, or the O-ring contact sur- faces. Apply a thin layer of the provid- ed silicone O-ring grease.

Align the threaded section of the PPO-E02 with the port mount thread on the PT-E series case. Hold the PT-E series case firmly with one hand, hold the main body of the PPO-E02 with your other

hand and screw it into the PT-E series by turning the PPO-E02 clockwise. Resistance increases as the PPO-E02 is screwed in more deeply. However, be sure to screw it in all the

way until there is no gap visible below the threaded section of the PPO-E02.

Olympus PPO-E02 — Disclaimer diagram (page 2)
Fig. 2 · Disclaimer
Page 3 of the Olympus PPO-E02 user manual — Disclaimer
Page 3 · cliquer pour agrandir
Page 3
Olympus PPO-E02 — Disclaimer diagram (page 3)
Fig. 3 · Disclaimer

If any water is on the product, wipe it completely away and

Holding the PT-E series case firmly with one hand, loosen the

PPO-E02 by turning it about 90 degrees counterclockwise. If the PPO-E02 is attached too tightly to turn, wrap it with a piece of rubber or similar non-slip material.

After loosening the PPO-E02, point its lens downward and

turn it further counterclockwise until it is separated from the PT-E series case. Be careful not to drop the PPO-E02 or PT-E series case.

ter on the lens or camera. If this happens, wipe the water off the lens and camera with a dry cloth. ・Make sure that the port is completely dry before dismounting.

Page 4 of the Olympus PPO-E02 user manual — 4 Attaching the Zoom Gear on the Lens
Page 4 · cliquer pour agrandir
Page 4

4 Attaching the Zoom Gear on the Lens

To control zooming of the camera lens, the provided zoom gear must be attached to the zoom ring of the lens.

Turn the zoom ring of the lens so that the correct number

(see the following table) is aligned with the zoom index.

Corresponding lens Number to align with the zoom index ZUIKO DIGITAL 14-54mm F2.8-3.5 25 ZUIKO DIGITAL 11-22mm F2.8-3.5 14

Check the position of the lock dial’s hinge on the zoom gear,

then turn the lock dial counterclockwise to release the lock and open the gear.

Open the zoom gear wide and align its hinge with the zoom

index on the lens. Place the zoom gear on the lens and adjust the rotation direction of the zoom gear. At this time, bring the gear section of the zoom gear to the left of the hinge as shown in the illustration.

Align the hinge with the index.

Set the front-rear direction of the zoom gear by aligning the

edge of the hinge with the end of the rubber section on the lens’ zoom ring.

After positioning the zoom gear, place it against the lens’s

zoom ring (taking care not to displace the zoom gear), and turn the zoom gear’s lock dial all the way clockwise to lock it. Push the gear with a finger to place the gear against the lens.

Turn the lock dial to lock the zoom gear.

zooming cannot be controlled properly. Be sure to attach the zoom gear correctly.

Show 4 more labels / short text on this page
Hinge · Open · Lock dial · Gear
Page 5 of the Olympus PPO-E02 user manual — 5 Loading the Camera and Lens
Page 5 · cliquer pour agrandir
Page 5

5 Loading the Camera and Lens

After attaching the zoom gear to the camera lens, insert the camera and lens into the PT-E series case on which the PPO-E02 is mounted.

Screw the camera table provided with the PT-E

Remove the eyecup from the camera’s viewfind-

series case firmly into the bottom of the cam- era.

er. If a lens cap or filter is attached to the lens or the strap is attached to the camera, remove them as well.

Pull out the zoom dial further.

Camera table lock lever

Lift the PT- E series case’s power switch dial,

Confirm that the camera’s power switch is OFF.

mode dial knob and zoom dial, and turn the case’s camera table lock lever counterclock- wise to release the lock. Refer to the PT-E series case’s instruction manual for instructions of how to attach the hot shoe cable for the flash.

Align the correct zoom value for the lens with the zoom index of the lens. While pulling out the zoom dial on the PT-E series case, slide the camera table with camera attached as far as it will go into the camera table mount on the inner side of the case’s front lid.

Show 4 more labels / short text on this page
Power switch dial · Mode dial knob · Zoom dial ·
Page 6 of the Olympus PPO-E02 user manual — 5 Loading the Camera and Lens
Page 6 · cliquer pour agrandir
Page 6

After inserting the camera, turn the PT- E series

Push in the PT- E series case’s power switch

case’s camera table lock lever all the way clock- wise to lock the camera table. Then, push in the zoom dial on the case and engage it with the zoom gear attached to the lens. Turn the zoom dial to confirm that it can control zooming.

dial and mode dial knob. Turn the power switch dial and mode dial knob and confirm that they can control the camera power ON-OFF and mode switching. Connect the hot shoe mount section of the hot shoe cable that has been connected to the PT-E series case to the hot shoe of the camera.

Attach the rear lid of the PT- E series case and

lock the four buckles (two diagonally located buckles first, and then the other two diagonally located buckles). Underwater shooting is now possible.

Page 7 of the Olympus PPO-E02 user manual — 6 Maintenance
Page 7 · cliquer pour agrandir
Page 7

6 Maintenance

For safe use of this product, always perform maintenance after each diving session. For details, refer to “Handling After Shooting” and “Maintaining the Waterproof Function” in the PT-E series case instruction manual. Apply the same procedures to this product.

Olympus PPO-E02 — 6 Maintenance diagram (page 7)
Fig. 4 · 6 Maintenance
Olympus PPO-E02 — 6 Maintenance diagram (page 7)
Fig. 5 · 6 Maintenance

era and lens, then re-seal the empty case and immerse it in tap water to remove any salt as soon as possible.

case is completely dry, dismount this product from the case.

Remove sand and dust from the O-rings.

using the provided pick for removing O-rings. Take care not to damage the O-rings.

Pinch each O-ring between your fingers and lightly rub the entire circumference to check for foreign matter, scratches and cracks.

Olympus PPO-E02 — 6 Maintenance diagram (page 7)
Fig. 6 · 6 Maintenance
Olympus PPO-E02 — 6 Maintenance diagram (page 7)
Fig. 7 · 6 Maintenance

If any foreign matter is attached to the

After removing foreign matter, apply the

O-ring grooves, remove it using a clean, lint-free cloth or cotton swab. Also remove any foreign matter from the O-ring contact surfaces and from the port mount thread on the PT-E series case.

provided grease to the O-rings and fit them into the O-ring grooves. To apply grease to each O-ring, squeeze a drop of grease about the size of a grain onto your finger and lightly rub the entire circumference of the O-ring to spread the grease thinly and evenly.

Page 8 of the Olympus PPO-E02 user manual — 8 Consumable Items
Page 8 · cliquer pour agrandir
Page 8

7 Specifications

Applicable case : PT- E series Applicable lens : ZUIKO DIGITAL 14-54mm F2.8-3.5/ZUIKO DIGITAL 11-22mm F2.8-3.5 Main materials Main body : Aluminum. Lens window : Chemically reinforced glass. O-rings : Silicon rubber. Zoom gear : Polycarbonate resin. Front cap : NBR rubber. Rear cap : Polyethylene resin. Withstanding pressure : Water depth of 60 m (200 ft) Dimensions : Max. diameter 143 mm x Depth 105 mm Weight : 650 g (excluding the conversion lens)

8 Consumable Items

This product uses the following consumable items.

  • Silicon O-rings
Olympus PPO-E02 — 8 Consumable Items diagram (page 8)
Fig. 8 · 8 Consumable Items

Description O-ring for use with the PT-E series case.

  • Grease for silicone O-ring

Shinjuku Monolith, 3-1 Nishi Shinjuku 2-chome, Shinjuku-ku, Tokyo, Japan

PremisesWendenstrasse 14-18, 20097 Hamburg, Germany

Tel: +49 40-23 77 3-0 Fax: +49 40-23 07 61 Goods delivery : Bredowstrasse 20, 22113 Hamburg, Germany Letters : Postfach 10 49 08, 20034 Hamburg, Germany

European Technical Customer Support: Please visit our homepage http://www.olympus-europa.com or call our TOLL FREE NUMBER* : 00800 - 67 10 83 00

Two Corporate Center Drive, Po Box 9058, Melville, NY 11747-9058, U.S.A. Tel. 631-844-5000

Technical Support (USA) 24/7 online automated help: http://www.olympusamerica.com/support Phone customer support: Tel. 1-888-553-4448 (Toll-free)

for Austria, Belgium, Denmark, Finland, France, Germany, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom *Please note that some (mobile) phone services/ provider do not permit access or request an additional prefix to +800 numbers.

Our phone customer support is available from 8 am to 10 pm (Monday to Friday) ET E-Mail: distec@olympus.com Olympus software updates can be obtained at: http://www.olympus.com/digital/

For all not listed European Countries and in case that you can’t get connected to the above mentioned number please make use of the following CHARGED NUMBERS: +49 180 5 - 67 10 83 or +49 40 - 237 73 899 Our Technical Customer Support is available from 9am to 6pm MET (Monday to Friday)

© 2005 OLYMPUS IMAGING CORP.

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Olympus PPO-E02

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Olympus PPO-E02

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Olympus PPO-E02 manuel PDF

60 pages·5.4 MB·Accessoires pour appareil photo·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…