
Installation These items include installation instructions.

A document output analysis of your business which could save you up to 30% on your printing costs.
Call 1-888-654-6264 to schedule an appointment with an Oki Managed Services project manager.
Or, for more information, go to WWW.OKIPRINTINGSOLUTIONS.COM
English · 5 • English

Settings made in the printer driver will override the printer menu settings.
If the MP Tray will normally be loaded with index cards, set the printer menu as follows:
to enter the Menu mode.
repeatedly to scroll through the Categories, Items and Values.
to select a Category, Item or Value to change, or to engage the new setting for a Value.
to exit the Menu mode.
or

Categories
This menu controls the operation of the printer’s Parallel data interface.
Print the Menu Map, Network settings or Demo page.
Set parameters for USB.
This menu only appears if the hard disk drive is installed. This item should always be selected before switching the printer off, to ensure that no hard disk data is lost.
Set network parameters.
Enable power save, and set other printer parameters.
Indicates page counts and remaining life for consumables.
Set the number of copies, feed tray used, etc.
Set media size and weight for the various trays, etc.
The MenuMap provides a listing of the current printer menu settings.
Set color density, registration, etc.
Sys Config Menu
Set power save, timeouts, etc.
This menu controls settings effective when the printer is operating in PCL emulation mode.
This menu controls settings effective when the printer is operating in PPR emulation mode.
This menu controls settings effective when the printer is operating in FX emulation mode.

Weight Media weight settings can be made in the printer menu or the printer driver.
Settings
Printer Driver Versus
Printer Menu Printer driver settings override printer menu settings.
Default Settings The default media weight setting for all trays is Medium.
Defaults
Media Weight for an Individual Print Job If you are printing a job on special media, you can temporarily load the media in a tray and change the media settings for that tray in the driver as you print the job.





6 Important! Adjust the paper size dial to the size of the paper being used.




Rear (Face Up) Exit Tray
This is the exit tray that is normally used.
If the rear tray is open, all printed pages will exit there regardless of the printer driver setting.


Edge

the Duplexer Open the file you wish to print and click File → Print. Select the C8800 Series printer.
Windows 1. For all but Windows 2000, click Properties or Preferences. Otherwise go to step 2.

Macintosh 1. Under Presets, select Duplex.
Paper Weight 20 to 28 lb. US Bond (75 to 105 g/m2).

Paper Feed Tray 1, Optional Tray 2 or MP Tray.
Paper Exit Top Exit Tray or Rear Exit tray.
Long Edge · Short Edge

Power Save sets how long the printer waits before going into standby mode. This saves energy, but the printer requires time to warm up when it receives a print job or if you want to enter the menu and change settings.
Power Save
The printer comes set for Power Save enabled. To disable (or enable) Power Save
Interval
POW SAVE TIME 60 MIN *
The second line of the display starts blinking.
The second line of the display starts blinking.
The new setting is engaged and the second line of the display stops blinking.
The new setting is engaged and the second line of the display stops blinking.















To remove a sheet trapped in the fuser:

Y
K








For additional error messages, see your on-line User’s Guide.
Appears on the second line of the display to indicate that consumable xxx needs to be replaced. Replace the indicated item. (See the instructions supplied with the item.)
Open the cover. Push the XXX Toner lock lever toward the back of the printer as far as it will go. Close the cover. If this does not clear the message, call your local service dealer.
LOAD mmm/ppp AND PRESS
The media type in the indicated tray (ttt) does not match that specified in the print job being processed. Load the appropriate media in the tray and press ON-LINE.
Appears on the second line of the display to indicate that consumable XXX (E.g., toner cartridge, image drum, belt, fuser) is nearing end of life.
LOAD mmm/ppp AND PRESS
If you have changed the LOW TONER setting to STOP, the ATTENTION light will blink and you must either replace the toner cartridge immediately or press the ON LINE button to continue printing.
The media size (mmm) and/or type (ppp) loaded in the indicated tray (ttt) does not match that specified in the print job being processed. Load the appropriate media in the tray and press ON-LINE.
Be sure you have a genuine OKI replacement toner cartridge on hand (see page 5).
Replace the XXXX toner cartridge with a genuine OKI Toner Cartridge.

CANCELING JOB (JAM)
The setting for Jam Recovery in the menu (under SYS COHNFIG MENU) has been changed to OFF. Any unprinted data is being deleted. Clear the jam (see page 16, ff.). Resend the missing pages of the print job.
Load more media (mmm) in the indicated tray (tttt).
Paper has jammed. Clear the jam: see page 16, ff.
PRESS ONLINE SWITCH INVALID DATA
The Job Accounting software has detected a print job from a user who is either • not authorized to print or
The printer has received invalid data. Press ON-LINE. Reprocess and resend the print job.

Consult the store where you purchased your printer.
OKI is a registered trademark of Oki Electric Industry Company, Ltd. AmEx is a registered trademark of American Express Co. MasterCard is a registered trademark of MasterCard International, Inc. VISA is a registered trademark of Visa. Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and other countries.
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.