Manuel d'utilisation / d'entretien du produit SM-8X4-HDA du fabricant Network Technologies
Aller à la page of 38
MAN066 Rev Date 04/4/2006 SM-8X4-HDA Audio/HD Video Matrix Switch Installation and Operation Manual V EEMUX ® Series NETWORK TECHNOLOGIES INCORPORATED Tel: 330- 562 -70 70 Fax :33 0-5 62- 199 9 1275 Dan ner D r Aurora, OH 44202 www.
i MAN066 Rev Date 04/4/2006 TRADEMARK VEEMUX is a registered trademark of Network Te chnologies Inc in the U.S. and other countri es. COPYRIGHT Copyright © 2006 by Net work Technologies Inc.
ii MAN066 Rev Date 04/4/2006 TABLE OF CONTENTS Introduct ion ...................................................................................................................................................................... 1 Materials ...........
iii MAN066 Rev Date 04/4/2006 Pinout of RS232 port on VEEM UX-A ............................................................................................... ......................... 30 Pinouts for typical DCE to DT E cable for CP U connect ion ...
NTI AUDIO/HD VI DEO MATRIX SWITCH 1 INTRODUCTION The VEEMUX SM-8X4-HDA (VEEMUX-A) is a versatile multi-input au dio/vide o matrix switch that independently switches e ight sets of incoming YPbPr component video a nd analog/digital audio si gnals to any or all of the four outputs.
NTI AUDIO/HD VI DEO MATRIX SWITCH 2 FEA TURES AND FUNCTIONS 1. LCD Display- for visual indication of input-to-out put connections and for conf iguration of the VEEMUX-A. 2. Keypad- buttons for user control over s witch functions 3. IEC Power Connector- for attachment of power cord 4.
NTI AUDIO/HD VI DEO MATRIX SWITCH 3 INST ALLA TION Connect the Sources 1. Turn OFF power to all video sources (inputs) that will be connected to the VEEMU X-A before connecting or disconnecting any cables. 2. Connect each video source to the VEEMUX-A using 4CEXT-xx BNC cabl es.
NTI AUDIO/HD VI DEO MATRIX SWITCH 4 Figure 2- Stereo audio connection block Connect the Devices 1. Connect each of the vi deo display devices to the VEEMUX-A using 3CEXT-xx or 4CEXT-xx cables. The groups of terminals are labeled OUTPUT 1-4. Use BNC to RCA adapters (as shown in figure 3) to connect the BNC cables to the devices.
NTI AUDIO/HD VI DEO MATRIX SWITCH 5 Connect RS232 RS232 control can be achieved using a separate user terminal or CPU with a terminal program. To make a terminal connection, connect a seria l cable (specif ications on page 30) bet ween the us er terminal and the 9 pin DIN female connector on the VEEMUX-A labeled "RS232".
NTI AUDIO/HD VI DEO MATRIX SWITCH 6 Power Up 1. Connect the IEC power cord to the VEEMUX-A and plug the cord into an AC p ower outlet. 2. Turn ON power to the VEEMUX-A us ing the switch abov e the IEC socket. 3. Turn ON power to the video and audio so urces, and the video and audio devices conn ected to the VEEMUX-A, if they are not already ON.
NTI AUDIO/HD VI DEO MATRIX SWITCH 7 CONTROL OPTIONS The VEEMUX-A video matrix switch has four methods of control: • F ront Panel LCD with Keypad • Directl y via an RS232 Interface • Remote ly via Ethernet (web interface) • Infrared Rem ote (optional).
NTI AUDIO/HD VI DEO MATRIX SWITCH 8 Volume Control The volume level can be adjuste d on each output port. • To increment < ▲ > or decrement < ▼ > the volume, use the follo wing comma.
NTI AUDIO/HD VI DEO MATRIX SWITCH 9 Scan Mode Scan Mode causes output ports (audio and video) to a utomati cally switch from one audio and video in put port to the next consecutive audio and vid eo input port after a specified peri od of time (referred to as the dwell time).
NTI AUDIO/HD VI DEO MATRIX SWITCH 10 RS232 Control Remote Connection The RS232 Interface is designed to control the s witch via serial (RS232) daisy ch ain connection from any host computer or oth er controller with an RS232 communicatio ns port.
NTI AUDIO/HD VI DEO MATRIX SWITCH 11 Command Protocol CPU controller commands supported b y the unit are defined belo w. All commands should be terminated with a <CR> (carriage return). When a command is sent, the entire string is echoed back to the CPU alon g with a response from the addressed unit as shown in the command definitio ns.
NTI AUDIO/HD VI DEO MATRIX SWITCH 12 Set Volume Level For Output/User Port (for command string AV SW,OP,VV in chart on page 11) This command will set the volume of the specified AUDIO output/user p ort from a scale of 00 to 99, which represents a logarithm ic volume.
NTI AUDIO/HD VI DEO MATRIX SWITCH 13 Matrix Operations Key Selection Description 1) Connect Video Output/User to an Input/CPU - connect an output to an input 2) Connect All Video Outputs/Users to an I.
NTI AUDIO/HD VI DEO MATRIX SWITCH 14 Telnet Interface The Telnet Interface enables the user to control the s witch using telnet client thro ugh an Ethernet connection. T he telnet ser ver listens on port 2000 . To access the telnet interface, using the curr ent IP address t ype the following in a command shell: telnet 192.
NTI AUDIO/HD VI DEO MATRIX SWITCH 15 Sc nn *<CR> Clear scan list of individual output nn S+ nn,mm *<CR> Add input mm to Scan List of output nn S- nn,mm *<CR> Remove inp ut mm from Sc.
NTI AUDIO/HD VI DEO MATRIX SWITCH 16 Web Interface A user may control the connections of t he VEEMUX-A using a Web Interface via any web browser (see page 1 for web supported browsers). With the VEEMUX-A connected to a LAN through an Ethernet cable, a user can access the web interface controls inside the VEEMUX-A.
NTI AUDIO/HD VI DEO MATRIX SWITCH 17 Video Switch Page The Video Switch page (right) displ ays the active connections (shown in orang e) and enables the user to control the audio and video connectio ns of the VEEMUX-A, or just the video. (To change audio connections separately, see pag e 18.
NTI AUDIO/HD VI DEO MATRIX SWITCH 18 To load a sav ed configuration , from the Stored Configuratio ns user interface, use the drop-down list to select the desired configuration. T hen press the Load button. The VEEMUX-A w i ll make th e connections and the screen will refresh to show the connections associat e d with that configuration selection.
NTI AUDIO/HD VI DEO MATRIX SWITCH 19 Serial Data (VV) Audio Volume Serial Data (VV) Audio Volume 90-99 +10dB 40 -40dB 80 0dB 30 -50dB 70 -10dB 20 -60dB 60 -20dB 10 -70dB 50 -30dB 0 -80dB Place a checkmark in the Mute box for any output port where no volume is desired.
NTI AUDIO/HD VI DEO MATRIX SWITCH 20 Figure 13- Web interface Serial S etup page Changes to the Serial Address and S erial Speed (Fig. 13) do not require a reset and will take effect immediately.
NTI AUDIO/HD VI DEO MATRIX SWITCH 21 Output Names From the Administration menu, the Video or Audi o Output Names page can be displa yed. (Selected separately from the menu.) These pages enable the Adm inistrator to change the names of the output ports displa yed on the Switch page.
NTI AUDIO/HD VI DEO MATRIX SWITCH 22 Update Firmware F i gu re 17- W eb interface Update Firmw are p ag e The Update Firmware pa ge (found in the main menu under "ADMINISTRAT ION") shows the current version of the firmware and enables the Administrator to updat e the firmware of the VEEMUX-A.
NTI AUDIO/HD VI DEO MATRIX SWITCH 23 Change Password Page Use this page to change the password for accessing the web interface. (This password is also used for the telnet interface.) Be sure to make note of the new password exactly as it is case sensitive.
NTI AUDIO/HD VI DEO MATRIX SWITCH 24 DEVICE DISCOVER Y TOOL In order to easily locate the VEEMUX-A on a net work, and change the IP settings, the NTI Device Discovery Tool may be used. A link to the Discovery Tool is provided o n the web page that appears when you insert the instruction manual CD provi ded into your CD ROM drive.
NTI AUDIO/HD VI DEO MATRIX SWITCH 25 12 3 45 6 78 9 0 OUT IN SYS Lo B a tt NTI R Netw ork Tec hnolog ies In c IR T- 64 X 32 SW INFRARED CONTROL (Optional) The IRT-64X32 (or IRT) is an infrared rem ote.
NTI AUDIO/HD VI DEO MATRIX SWITCH 26 How To Use The IRT The IRT-64X32 enabl es the user to control the connections of up to 32 input ports and 16 output ports on up to four (4) separat e NTI video matrix switches. When an y key is pressed, the IRT will po wer ON.
NTI AUDIO/HD VI DEO MATRIX SWITCH 27 Change Output Port Press the desired port number. If there is no change in the desired output port, the output port must still be selected. A s the digits are se lected, the last nu mber entered will blin k. The LCD will al so display the current sw itch number fol lo wed by the decimal point.
NTI AUDIO/HD VI DEO MATRIX SWITCH 28 Set Configuration The IRT-64x32 factory d efault setting is 32 inputs and 16 outputs . When the batteri es are changed the setting will return to th e default value.
NTI AUDIO/HD VI DEO MATRIX SWITCH 29 Battery Replacement The IRT has a low-battery indicator to let the user kno w when it is time to change the batteries.
NTI AUDIO/HD VI DEO MATRIX SWITCH 30 RS232 CONNECTION CABLES Pinout of RS232 port on VEEMUX-A The VEEMUX-A RS232 serial port is a DB-9F (female) connector configure d as a DCE (data communication equipment) port. The RS232 port interface signals ar e listed below, including eq uivalent CCITT V.
NTI AUDIO/HD VI DEO MATRIX SWITCH 31 Pinout for Matrix Y-1 Cable Arrows indicate signal direction. Figure 22- Pinout for Matrix Y-1 Cable SAFETY ST A TEMENTS Grounding These products have protective earth gr ound te rminals and are bui lt with full attention to consumer safety.
NTI AUDIO/HD VI DEO MATRIX SWITCH 32 RACK MOUNTING INSTRUCTIONS This NTI switch was designed to be directly mounted to a ra ck. It includes a mou nting flange to make attachment easy. Install 4 captive nuts to the rack in locati ons that line up with the holes (or slots) in the mounting flange on the NTI s witch .
NTI AUDIO/HD VI DEO MATRIX SWITCH 33 SPECIFICA TIONS DESCRIPTION SPECIFICATION Video Video Connectors BNC Maximum Resolution 1920X1080@ 60Hz Supported Signals Component vi deo, S-video, Composit e video Input/Output Impedance 75 ohm Maximum Input / Output Lev els 1.
NTI AUDIO/HD VI DEO MATRIX SWITCH 34 TROUBLESHOOTING Problem Solution No Video - Check power – power ON, power cable connected - Check video cabling – make sure cables are sec ured - Check connect.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Network Technologies SM-8X4-HDA c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Network Technologies SM-8X4-HDA - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Network Technologies SM-8X4-HDA, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Network Technologies SM-8X4-HDA va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Network Technologies SM-8X4-HDA, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Network Technologies SM-8X4-HDA.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Network Technologies SM-8X4-HDA. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Network Technologies SM-8X4-HDA ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
