Manuel d'utilisation / d'entretien du produit GT6000 du fabricant NEC
Aller à la page of 117
GT6000/GT5000 LCD Projector User ’ s Manual.
ii Important Information Precautions Please read this manual carefully bef ore using your NEC GT6000/ GT5000 Projector and keep the man ual handy for future ref er- ence.
iii Power Supply 1. The projector is designed to oper ate on a power supply of 100- 120 or 200-240 V 50/60 Hz AC . Ensure that your power supply fits this requirement before attempting to use y our projector . 2. Handle the po wer cable carefully and a void e xcessive bending.
iv T able of Contents 1. Introduction z What's in the Box? .................................................................... 1-2 x Introduction to the Pr ojector ................................................... 1-3 c Getting to Know Y our Projector .
1 Introduction z What's in the Bo x? .................................................... 1-2 x Introduction to the Projector ..................................... 1-3 c Getting to Know Y our Projector ................................. 1-4 Attaching the lens hood cap to the lens hood with the supplied string and rivet .
1-2 z What's in the Box? Make sure your bo x contains e verything listed. If any pieces are missing, contact y our dealer. Please sav e the original box and packing materials if y ou ev er need to ship your Projector . NOTE: Lenses are optional. Order lenses from your NEC dealer .
1-3 x Introduction to the Pr ojector This chapter introduces you to the GT6000/GT5000 high end fixed installation projector and describes k ey f eatures and con- trols. Congratulations on Y our Pur chase of the GT6000/GT5000 projector The GT6000/GT5000 is our most sophisticated three panel, dual lamp XGA LCD projector .
1-4 1. Introduction A U D I O A U D IO O U T R R / Cr G /Y B / C b V H / HV R L/MONO R L/MONO R L/MONO L/MON O DVI R G B O U T R GB 1 R GB 2 A U D I O S L O T 1 S L O T 2 VIDEO S-VIDEO P C C O N T R O.
1-5 USB ( MOUSE/HUB ) USB ( PC ) PC CARD 1 2 PC CONTROL IN IN OUT OUT SC TRIGGER REMOTE 2 REMOTE 1 LAN AC IN AUDIO AUDIO AUDIO OUT R R/Cr G/Y B/Cb V H/ HV R L/MONO R L/MONO R L/MONO L/MONO SLOT 1 SLOT.
1-6 Attaching the lens hood cap to the lens hood with the supplied string and rivet 1. Thread the string through the hole on the lens hood cap. Lens hood cap String 2.
1-7 3D REFORM 3D A SELECT LENS SHIFT FOCUS ZOOM DOWN LEFT RIGHT UP Z STATUS PC CARD 2 PC CARD 1 LAMP 1 LAMP 2 POWER ON/STAND BY AUTO ADJUST M E N U E N T E R C A N C E L F 1 7 2 3 54 6 13 14 11 8 9 12 10 T op Features 1.
1-8 1. Introduction AUDIO AUDIO AUDIO OUT R R/Cr G/Y B/Cb V H/ HV R L/MONO R L/MONO R L/MONO L/MONO SLOT 1 SLOT 2 DVI RGB OUT RGB 1 RGB 2 VIDEO S-VIDEO 3 8 1 2 4 56 7 T erminal Panel Features 1. RGB 1 Connectors [R/Cr , G/Y , B/Cb, H/V , V] (BNC) Connect R,G,B,H (Horizontal sync) and V (V er tical sync) out- puts of external equipment.
1-9 USB ( MOUSE/HUB ) USB ( PC ) PC CARD 2 1 PC CONTROL IN IN OUT OUT SC TRIGGER REMOTE 2 REMOTE 1 LAN AC IN 12 3 7 4 8 9 10 11 5 6 1. USB P or t [MOUSE/HUB] (T ype A) Connect a USB mouse. Y ou can oper ate the menu or Viewer with a USB mouse via this por t.
1-10 1. Introduction OFF + - PICTURE ADJUST ABC DEF GHI JKL MNO PQR STU ,. UNDO CANCEL TEST PICTURE KEYSTONE AMPLITUDE ENTRYLIST SOUND OSD MUTE MAGNIFY HELP INFO.
1-11 1. Introduction OFF + - IC TURE ADJUST BC DEF M WHITE BAL. IMAGE ON POWER MENU ENTER 2 ADDRESS P RO BS 27 28 10. UNDO Press to return the adjustments and settings to the previous condition. While pressing and holding CTL, pressing this but- ton clears the entire menus or adjustment/setting screen.
1-12 1. Introduction 7m 30˚ 30˚ Remote Control Precautions • The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the main unit, or when there is an obstacle in the path. • When remote control buttons are pressed and held, projector’ s function ke ys may not operate .
1-13 AUDIO AUDIO AUDIO OUT R R/Cr G/Y B/Cb V H/ HV R L/MONO R L/MONO R L/MONO L/MONO SLOT 1 SLOT 2 DVI RGB OUT RGB 1 RGB 2 VIDEO S-VIDEO USB ( MOUSE/HUB ) USB ( PC ) PC CARD 2 1 PC CONTROL IN IN OUT OUT SC TRIGGER REMOTE 2 REMOTE 1 LAN AC IN REMOTE 2 IN OFF + - PICTURE ADJUST ABC DEF GHI JKL MNO PQR STU ,.
2-1 2 Installation z Setting Up Y our Projector .......................................... 2-2 Screen Size and Projection Distance .................................................................. 2-2 x Lens Shift Adjustable Range ...................
2-2 List of Screen Sizes Screen size Width (H) Height (V) m inch m inch 40" 0.8 31.5 0.6 23.6 60" 1.2 47.2 0.9 35.4 80" 1.6 63.0 1.2 47.2 100" 2.0 78.7 1.5 59.1 120" 2.4 94.5 1.8 70.9 150" 3.0 118.1 2.3 90.6 200" 4.1 161.
2-3 GT34ZLB (H ⳯ 3.2) - (H ⳯ 4.8) GT24ZLB (H ⳯ 2.2) - (H ⳯ 3.2) GT20ZL (H ⳯ 2.0) - (H ⳯ 2.6) GT13ZLB (H ⳯ 1.2) - (H ⳯ 1.5) GT12ZLB (H ⳯ 1.2) - (H ⳯ 1.7) GT10RLB (H ⳯ 1.0) GT06RLB (H ⳯ 0.6) GT48ZLB (H ⳯ 4.8) - (H ⳯ 7.1) GT19ZLB (H ⳯ 1.
2-4 1H 1H 0.32H 0.5V 0.5V 0.5V 0.32H 0.32H 0.32H 1V 1V 0.5V 1V Desktop/Front Vertical Ceiling/Front Vertical Normal position Normal position Normal position Horizontal Normal projection position x Lens Shift Adjustable Range The top right diagram shows the location of the image position in the lens.
2-5 Lens Shift Adjustable Range (continued) The top right diagram shows the location of the image position in the lens. The lens can be shifted within the shaded area as s hown using the normal projection position as a star ting point. Maximum Possible Range for GT13ZLB/GT19ZLB/GT24ZLB/GT34ZLB: V alues in parentheses f or GT13ZLB.
2-6 2 c Optional Lens Installation This section describes how to install the lens. See page 2-8 for installing the GT12ZLB lens and page 2-10 f or the GT06RLB lens. Before installation * Deter mine the optional lens to be used to obtain a desired projection distance.
2-7 I N O U T RE M O TE 2 AC IN AUD IO A U D IO O U T R R /Cr G /Y B /Cb V H/ H V R L / MO N O R L /M O N O R L/M O N O L/ M ON O DVI RG B O U T RGB 1 RGB 2 VIDEO S-VIDEO AU DIO S LO T 1 S L O T 2 4 3.
2-8 For installing the GT12ZLB Preparation: T ools needed f or installation: A he xagonal dr iver is supplied with the optional lens. 1. Remov e the lens hood cap and lens hood. q Remov e the lens hood cap. w Loosen and remov e the 2 screws on the lens hood using the he xagonal driver .
2-9 IN O U T R E M O T E 2 AC IN A UD IO A U D I O O U T R R /C r G /Y B/ Cb V H / H V R L /M O N O R L / M ON O R L / M O N O L / M O N O DVI R GB OUT RGB 1 RGB 2 VIDEO S-VIDEO A U DIO S LOT 1 S L OT.
2-10 For installing the GT06RLB Preparation: T ools needed f or installation: A he xagonal dr iver is supplied with the optional lens. 1. Remov e the lens hood cap and lens hood. q Remov e the lens hood cap. w Loosen and remov e the 2 screws on the lens hood using the he xagonal driver .
2-11 IN O U T R E M O T E 2 A C I N A UD IO A U D IO O U T R R/ C r G/Y B /C b V H / H V R L / M O N O R L / M O N O R L / M O N O L / M O N O D VI R G B O U T RG B 1 RGB 2 V IDEO S -V ID EO A UD IO S.
2-12 r Reattach the front par t which was remov ed on step q above and rotate the knob in clockwise direction to secure it. t Remov e the front lens cap from the lens unit. This completes installation. If necessary , put the lens hood cap on the lens hood.
2-13 v Making Connections NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from the RGB output unless the notebook PC is turned on after connecting with the projector .
2-14 T o connect SCART output (RGB) Before connections: An e xclusive SCAR T adapter (ADP-SC1) and a commercially availab le SCAR T cable are required for this connection. NOTE: • Audio signal is not available for this connection. • The RGB 1 IN connector does not support Plug & Play .
2-15 AUDIO OUT L AUDIO IN LR R Component YC b C r USB A USB B PC CARD PC CONTROL IN IN OUT OUT SC TRIGGER REMOTE 2 REMOTE 1 LAN AC IN AUDIO AUDIO AUDIO OUT R R/Cr G/Y B/Cb V H/ HV R L/MONO R L/MONO R .
2-16 AUDIO OUT L R VIDEO OUT S-VIDEO VIDEO AUDIO IN LR USB A USB B PC CARD PC CONTROL IN IN OUT OUT SC TRIGGER REMOTE 2 REMOTE 1 LAN AC IN AUDIO AUDIO AUDIO OUT R R/Cr G/Y B/Cb V H/ HV R L/MONO R L/MO.
2-17 2. Installation Connecting to a Network With the LAN connection, you can control the projector o ver the network using a computer to s witch the unit on/off, select the input and others. * T o control the projector over the network using a computer , use the Dynamic Image Utility 2.
2-18 2. Installation Connecting the Supplied Power Cable Connect the supplied power cable to the projector . First connect the supplied power cab le's three-pin plug to the AC IN of the projector , and then connect the other plug of the supplied pow er cable in the wall outlet.
3 Projecting an Image (Basic Operation) z T urning on the Projector ............................................ 3-2 x Selecting a Source ................................................... 3-3 c Adjusting the Picture Size and P osition ..............
3-2 3. Projecting an Image This chapter describes how to turn on the projector and to project a pic- ture onto the screen. z T urning on the Projector NOTE: • When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off[O] position.
3-3 3. Projecting an Image x Selecting a Source Selecting the computer or video source Using the Remote Control Press the Source/Number button (0-9) to se- lect input. 1 ...... RGB 1 input 2 ...... RGB 2 input 3 ...... D VI (DIGIT AL) input 4 ...... VIDEO input 5 .
3-4 v Correcting the Horizontal and V ertical Keystone Distortion (3D Reform) Use the 3D Reform feature to correct k eystone (trapez oidal) distor tion to make the top or bottom and the left or right side of the screen longer or shor ter so that the projected image is rectangular .
3-5 3. Press the 3D REFORM button on the remote control. The Cornerstone adjustment screen is displayed. The Cornerstone adjustment screen will disappear when you mov e the USB mouse cursor . 4. Point to one of the remaining 3 corners and left-click on it.
3-6 The confirmation screen is displayed. On the Cornerstone adjustment screen, select “Exit” and then “OK”, or press the CANCEL but- ton on the remote control. 8. Use the SELECT 왖왔왗왘 button to select another icon which points in the direction.
3-7 m T urning off the Projector T o turn off the projector: First press the POWER (ON/ST AND BY) button on the projector cabinet or the POWER OFF b utton on the remote control for a minimum of two seconds.
4 Convenient Features z T urning Off the Image and Sound ............................. 4-2 x Enlarging and Moving a Picture ................................ 4-2 c Getting the On-line Help and Inf or mation ................. 4-2 v Using a USB Mouse ...
4-2 z T urning Off the Image and Sound Press the MUTE PICTURE button to turn off the image and sound for a shor t period of time. Press again to restore the image and sound. x Enlarging and Moving a Picture Y ou can enlarge the area you w ant up to 400 percent.
4-3 v Using the USB Mouse Using a commercially av ailable USB mouse gives y ou smooth operation. NOTE: There may be some brands of USB mouse that the projector does not sup- port. Operate the Projector Menus using the USB mouse Mouse Cursor When connecting a USB mouse to the projector , you get a mouse cursor on the screen.
4-4 n Changing Backgr ound Logo Y ou can change the default bac kground logo using the PC Card Files feature . NOTE: File size must be 256KB or less. File formats other than JPEG and BMP are not available.
4-5 This function ser ves to store the adjusted v alue when using the Shift, Focus , and Zoom buttons of the projector or the remote control. Reference memory: Reference P oint ....... Adjusted settings are stored in memory as a ref erence com- mon to all the input sources.
5-1 5 Using the V iewer z Making the Most out of the Vie wer Function ............. 5-2 x Operating the Viewer Function from the Projector (pla yback) .
5-2 P C C O N T R O L I N I N O U T O S C T R I G G E R R E M O T E 2 R E M O T E 1 L A N U S B ( MOUSE/HUB ) U S B ( P C ) P C C A R D 2 1 NOTE: • T o use the Viewer , first you need to create presentation materials on your PC using the Dynamic Image Utility 2.
5-3 x Operating the V iewer Function from the Projector (playback) This section describes the operation for sho wing slides of pre- sentation documents created using the Viewer function with the projector . It is also possible to mak e slides directly from the im- ages projected with the projector .
5-4 Auto Play Mode If the "Auto Pla y" option is selected in "Viewer Options" of the menu, any giv en slide will star t to play automatically .
5-5 Deleting Captured Images Using the Delete button on the tool bar f or Viewer can delete captured images. T o delete captured images: 1. Select Vie wer and display a f older list of captured images. 2. Use b utton to select the Capture folder “Cap” in the right bottom of the screen.
6-1 6 Using the Projector in a Network z End User License Agreement ................................... 6-2 x Introduction ............................................................... 6-3 c Suppor ted Projectors ....................................
6-2 Be sure to read this before installing and using the accompan y- ing software. z END USER LICENSE AGREEMENT PLEASE READ THIS SOFTW ARE LICENSE AGREEMENT ("LI- CENSE") CAREFULL Y BEFORE INST ALLING THE SOFTW ARE. IT PRO VIDES THE TERMS OF THIS LICENSE.
6-3 x Introduction Thank you f or your purchase of the NEC portable projector (here- after referred to as "unit" or "projector"). This projector is connected to a personal computer or other equip- ment and clearly projects text or graphics to a screen.
6-4 c Supported Projectors The follo wing NEC projectors will be suppor ted: GT6000/GT5000* 1 , MT1065/MT1060/MT860, L T260/L T240/L T220/L T260K/L T240K/WT600 and VT770* 2 . *1 The GT6000/GT5000 comes standard with a LAN por t (RJ-45). *2 The whole functions of Image Express Utility 1.
6-5 v Equipment Connections and Settings When Using a Network Environment What Can Be Accomplished • Using Image Express Utility 1.0, the screen image display ed by the personal computer can be sent to the projector and then projected to a screen. • Using Dynamic Image Utility 2.
6-6 b Software Installation NOTE • Windows XP operations will be described in examples given here. • When using Windows 2000, please per form software installation/uninstalling with "Administrators" authority . When using Windows XP , perform with "Computer Administrator" authority .
6-7 n Starting/Exiting the Software NOTE: Windows XP operations will be described in examples given here. Dynamic Image Utility 2.0 Start the Software Preparation: Install the software on the personal computer from the supplied CD-ROM. (Page 6-6) The software cannot be started from the supplied CD-ROM.
6-8 m T r oubleshooting In this section, the software names ha ve been abbre viated as follo ws: Dynamic Image Utility 2.0 to DIU 2.0, Viewer PPT Con verter 2.0 to PPTC 2.0, and Image Express Utility 1.0 to IEU 1.0. <Problem> Installation does not complete normally .
6-9 <Problem> Projection to the screen is not possib le when using the LAN environment. (DIU 2.0, IEU 1.0) Check P oints Countermeasures Have LAN cards (i.e., adapters) been put into both the personal computer and the projector? Put LAN cards (i.
6-10 <Problem> The projector cannot be found with "General search" . (IEU 1.0) Check P oints Countermeasures Are the wir eless LAN settings appropriate? Are the channel numbers for the.
6-11 6. Using the Projector in a Network <Problem> When used in the LAN environment, the projector cannot be detected. (DIU 2.0, IEU 1.0) Check P oints Countermeasures If you have a personal firewall installed on your computer , the personal firewall may not allow for communication with the projector .
7-1 7 Setting Up for Double Stacking in Link Mode z Stacking and Connecting the Projectors .................. 7-2 x Adjusting and Registering Signals to Be Projected ........... 7-5 c Adjusting the Lens Shift, Zoom and F ocus to Clearly Displa y all projected patter ns .
7-2 7. Setting Up for Double Stacking in Link Mode z Stacking and Connecting the Projectors Master projector Slav e projector NOTE: Up to two units can be gravity stacked without external support. In some cases, however , two images will not align on the screen correctly .
7-3 7. Setting Up for Double Stacking in Link Mode Thro w Distances for Optional Lenses Master projector Slav e projector Throw Distance Screen center Recommended Throw Distances f or Double Stack NOTE: • The optional lenses for GT6000/GT5000 have different geometrical distortions in wide zoom and tele.
7-4 z -3. Hookup z -3-1. Use commercially a vailable RGB signal cab les to connect the RGB output of the master projector to the RGB input of the slav e projector until all the projectors are connected.
7-5 7. Setting Up for Double Stacking in Link Mode x Adjusting and Registering Signals to Be Projected x -1. Displa y a desired input signal on the master projector . x -2. Make adjustments to the signal, then sa ve (register) adjust- ments on the master projector by pressing and holding CTL and pressing ENTR Y LIST button on the remote control.
7-6 b List of Menu Items A vailable in Link Mode 7. Setting Up for Double Stacking in Link Mode A vailable Menu Items NO TE Source Select *1 Sound Menu Link Mode On/Off Timer Sleep Timer Source Inform.
8-1 8 Using On-Screen Menu z Basic Menu Operation ............................... 8-2 x List of Direct Button Combinations ............ 8-3 c Menu tree ................................................... 8-4 v Menu Descriptions & Functions .......
8-2 z Basic Menu Operation Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or projector cabinet to displa y the Basic, Advanced or Custom Menu.
8-3 x List of Direct Button Combinations CTL+ Input (1-10) Switches to any selected signal f ound in the Entry List. T o enable this combination, y ou must first assign specific remote b uttons for direct input selection in the Entry Edit window . CTL+ ENTER (While displa ying Entr y list) Displays the selected signal.
8-4 c Menu tree 8. Using On-Screen Menu Advanced Menu Source Select Adjust (Source) Sound Ref. Adjust Factory Default Projector Options Tools Help Test Pattern 1. RGB1 2. RGB2 3. DVI(DIGITAL) 4. Video 5. S-Video 6. Viewer 7. LAN 8. Slot 1 9. Slot 2 0.
8-5 8. Using On-Screen Menu Advanced Menu Source Select Adjust (Source) Sound Ref. Adjust Factory Default Projector Options Tools Help Test Pattern 3D Reform Screen Ref.
8-6 8. Using On-Screen Menu Advanced Menu Source Select Adjust (Source) Sound Ref. Adjust Factory Default Projector Options Tools Help Test Pattern Settings Status Status Mail Lamp Settings Link Mode .
8-7 Entering Alphanumeric Characters by Using the Menu Alphabet or numeric characters are used for y our IP address or projector name. T o enter an IP Address or projector name, use the software ke yboard. For using the softw are keyboard, see page 10-10.
8-8 Edit .............. Enables you to change source names or assign the direct ke y . Source Name Enter a signal name. Up to 18 alphan umer ic char- acters can be used. Input T erminal Change the input terminal. RGB1 and RGB2 are av ailable f or RGB signal; Video and S-Video are av ailable f or composite signal.
8-9 SweetVision The SweetVision f eature provides improv ement of contrast us- ing a proprietar y detail enhancement technology . NOTE: This feature is not available for 480p, 576p and HDTV signals. Off ............... T ur ns off the SweetVision feature Low .
8-10 Selecting Gamma Correction Mode Use the 왗 or 왘 buttons to choose one mode from three options . Each mode is recommended f or : Dynamic ...... F or true color reproduction of natural tones Natural .
8-11 Sync Protection When a VCR, D VD , or some other equipment that suppor ts Copyguard (a cop y prev ention system) is pla yed back, the screen may be displa yed in a curved manner . Adjustments are made in such circumstances. Use the SELECT 왗 or 왘 b utton to adjust the VD lev el.
8-12 Ref. Adjust Using 3D Reform This f eature corrects trapezoidal distortion so that the projected image is rectangular . T wo options are a vailable f or correcting procedures. Y ou can save adjustment settings b y using the 3D Reform Save option on Setup (See page 8-16).
8-13 Reference Lens Memory [Ref. Lens Memmory] This function serves to store the adjusted value common to all input sources when using the Shift, Focus , and Zoom buttons of the main unit or the remote control. Set Reference P oint ............. Stores the current adjusted v al- ues in memor y as a ref erence.
8-14 Selecting Menu Displa y Time This option allows y ou to select how long the projector waits after the last touch of a button to turn off the menu. The preset choices are "Manual", "A uto 5 sec", "Auto 15 sec", and "Auto 45 sec".
8-15 Setup [Pa g e 1] Selecting Projector Orientation [Orientation] This reorients your image f or your type of projection. The op- tions are: desktop front projection, ceiling rear projection, desk- top rear projection, and ceiling front projection.
8-16 Selecting Operation Mode [Operation Mode Select] Set the operation mode of the USB mouse connected to the USB por t (MOUSE/HUB) on the projector Auto .
8-17 Enabling Last Memory [Last Memor y] The projector stores the last signal data in memor y f or each input (RGB1, RGB2, D VI DIGIT AL, Video , S-Video and Slot 1/ 2). This f eature will reduce switching time between sources. If a commercially av ailable s witcher is connected, tur ning on this feature ma y cause the image to appear incorrectly .
8-18 Disabling the Cabinet Buttons [Control P anel K ey Loc k] This option turns on or off the Control Panel K e y Lock function. NOTE: * This Control Panel Key Lock does not affect the remote control functions. * When the cabinet buttons are disabled, pressing and holding the CANCEL button for about 10 seconds will change the setting to enable.
8-19 Status Displa ying Current Status of Link Mode When selecting the tab "Status", you will get the f ollowing dia- log box. Master ID ................. Indicates the Master projector Status ...................... Indicates the status of the master pro- jector Connected PJ .
8-20 Advanced IP Address An IP address can be automatically assigned to this projector by y our DHCP ser ver . If y our network does not automatically assign IP address, ask y our network administrator for an ad- dress, and then register it manually .
8-21 WEP (for Wireless only) Select this option whether using the WEP (Wired Equivalent Pri- vacy) k ey f or encr yption or not. T o use encr yption, specify WEP key . Disable ........ Will not turn on the encr yption f eature. Y our com- munications ma y be monitored by someone.
8-22 Mail NOTE: T o the Mail Alert feature on wireless LAN connection, select "Infrastructure" for "Mode" in "Network T ype." . Aler t Mail: Checking this bo x enables Alert Mail feature. This option notifies your computer of an error message via e- mail when using wireless or wired LAN.
8-23 8. Using On-Screen Menu Seamless Switch (GT6000 only) 1. What Does This Function Do? This function provides a transition eff ect during source switch- ing. [Before switching] [During switching] [After switching] * The drawings sho w an example of how “Eff ect-Wipe Right” works.
8-24 8. Using On-Screen Menu Setting a Password A password can be set for your projector to avoid operation by an unauthorized person. There are two pass word options: one for men u and the other for logo. When a password is set, doing an y one of the f ollowing four op- erations will display the P ass word input screen.
8-25 Enable/Disable ........ This tur ns the Security function on or off. Keyword .................. Enter an appropriate keyword when you use the Security function. (Up to 10 characters can be used.) The Security function is available only when your keyword is entered.
8-26 (3) When you attempt to display an image for which security is set while the security function is enabled • Blanks (spaces) cannot be used in the Keyword section. T o delete PC car d data you registered. 1. Use the SELECT 왖왔 button to select "Delete" and use the SELECT 왗 button to select the list windo w .
8-27 8. Using On-Screen Menu 3. Select “Edit” and press the ENTER button to open the Edit window . 4. Set the Day , Time (24 hours f ormat), On-Time and Off-Time using the SELECT buttons and the Softw are keyboard (1 thru 10). 5. Select On Timer or Off Timer 6.
8-28 8. Using On-Screen Menu Enabling Sleep Timer 1. Select your desired time between 30 minutes and 16 hours: Off , 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00. 2. Select “Set” and press the ENTER button on the remote control. 3. The remaining time star ts counting down.
8-29 8. Using On-Screen Menu T ype Standard lamp Extended lif e lamp Normal 2000H Eco 3000H Model GT60LP GT60LPS 4500H Lamp lif e (H) P age 2 Signal T ype, Video T ype, Sync T ype, Interlace, Direct K ey Projector Information Displays the inf ormation for your projector such as lamp usage , filter usage, v ersion number and others.
9 Maintenance z Replacing the Lamp .................................................. 9-2 x Replacing or Cleaning the Filter ..........................
9-2 This chapter describes the simple maintenance procedures you should follo w to replace the lamp and the filter , and to clean the filter and the cabinet. z Replacing the Lamp The projector has two lamps. The lamp replacement procedure applies to both lamps.
9-3 x Replacing or Cleaning the Filter T o replace the filter: • Replace both filters at the same time. • Before replacing the filters , remove dust and dirt from the pro- jector cabinet. • The projector contains high-precision par ts. K eep out dust and dir t during filter replacement.
9-4 1. T urn off the projector bef ore cleaning. 2. Clean the cabinet per iodically with a damp cloth. If heavily soiled, use a mild detergent. Ne ver use strong detergents or solv ents such as alcohol or thinner . 3. Use a blower or lens paper to clean the lens , and be careful not to scratch or mar the lens.
10 Appendix z USB Memor y De vice or USB Memor y Card Reader Suppor t .... 10-2 x T roub leshooting ...................................................... 10-3 c Specifications ......................................................... 10-5 v Cabinet Dimensions .
10-2 10. Appendix z USB Memory Device or USB Memory Card Reader Support The projector is compatible with either a USB memory device or USB memory card reader which suppor ts the view er and secu- rity features . • T o use a USB memory device or USB memory card reader, connect the de vice to the USB por t (type A).
10-3 x T r oubleshooting This section helps you resolv e problems you ma y encounter while setting up or using the projector . Power Indicator Indicator Condition Projector Condition Note Off Blinking light Steady light Green blinking Orange blinking 0.
10-4 Does not turn on Will turn off No picture Image isn’t square to the screen Picture is blurred Image is scrolling verti- cally , horizontally or both Remote control does not work Indicator is li.
10-5 10. Appendix If there is no picture, or the picture is not displa yed correctly . • Power on process for the projector and the PC. Be sure to connect the RGB cable between the projector and the computer bef ore turning on the computer .
10-6 c Specifications This section provides technical inf or mation about the GT6000/GT5000 Projector’ s perf or mance. Model Number GT6000/GT5000 Optical LCD Panel 1.
10-7 Built-in Speakers 5W ⳯ 2 P ower Requirement 100 - 120V A C / 200 - 240 V A C, 50 / 60 Hz Input Current 8.0 A (100 - 120 V A C) / 4.0A (200 - 240 V A C) P ower Consumption 800W (Lamp Nor mal mode) (2 lamps) 660W (Lamp Eco mode) 1W (Standby) Mechanical Dimensions 20.
10-8 USB ( MOUSE/HUB ) USB ( PC ) PC CARD 1 2 PC CONTROL IN IN OUT OUT SC TRIGGER REMOTE 2 REMOTE 1 LAN AC IN 3D REFORM 3D A SELECT LENS SHIFT FOCUS ZOOM DOWN LEFT RIGHT UP Z STATUS PC CARD 2 PC CARD .
10-9 n Compatible Input Signal List Signal Resolution F requency H. Refresh Rate ( Dots ) ( kHz ) ( Hz ) NTSC – 15.734 60 P AL – 15.625 50 SECAM – 15.625 50 VESA 640 ⳯ 480 31.47 59.94 IBM 640 ⳯ 480 31.47 60 MA C 640 ⳯ 480 31.47 60 MA C 640 ⳯ 480 34.
10-10 m REMOTE 1 Connector 51 42 3 10 11 12 13 14 15 6 97 8 This connector is used for a third party external control device . Pin No. 14 5 10 3 4,8,12,11 SHORT/OPEN SHORT OPEN SHORT OPEN SHORT OPEN S.
10-11 15 24 3 67 9 8 Cable Connection Communication Protocol Baud rate ........................ 38400 bps Data length ..................... 8 bits P arity .............................. No parity Stop bit ........................... One bit X on/off .
10-12 ⁄0 Operation Using an HTTP Browser Overview The use of HTTP server functions will allow control of the projec- tor from a web browser without the installation of special soft- ware. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version f or the web browser .
10-13 Source Select: This switches the input connector of the projec- tor . RGB1 ...................... Switches to the RGB 1 connector . RGB2 ...................... Switches to the RGB 2 connector . D VI(DIGIT AL) ........... Switches to the D VI connector .
NEC SOLUTIONS’ PROJECTOR PRODUCTS NEC Solutions (America), Inc. (hereafter NEC Solutions) warrants this product to be free from defects in material and workmanship under the following terms.
DECLARA TION OF CONFORMITY U.S. Responsible Party: Address: Tel. No.: NEC Solutions (America), Inc. 1250 N. Arlington Heights Road Itasca, Illinois 60143 (630) 467-5000 Type of Product: Equipment Clas.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté NEC GT6000 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du NEC GT6000 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation NEC GT6000, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le NEC GT6000 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le NEC GT6000, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du NEC GT6000.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le NEC GT6000. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei NEC GT6000 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
