Manuel d'utilisation / d'entretien du produit Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, du fabricant Metz
Aller à la page of 68
TV . VIDEO. AUDIO. MEC ABLITZ Spectral-MF PIP 72 T F 80 – 100 HT Astral-MF PIP 72 T F 81 – 100 HT T aros-MF PIP 72 T F 82 – 100 HT Carat-SF 72 T F 83 – 100 HT Stratos-SF PIP 72 T F 86 – 100 .
2 Contents Remote control handset RD 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 1. Setting up and connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 Turning the TV on and off . . . . . . . . . . . . .
3 Batteries: Insert the enclosed batteries in the remote control, observing the symbols on the cover of the battery compartment. Remove exhausted batteries from the remote control and return them to your dealer or to an authorised battery collection point.
4 Connecting the aerial Standard SAT and terrestrial station aerial sockets are fitted at the rear of the TV. Thunderstorms represent a danger for all electrical appliances! If lightning strikes the power line or the aerial, the TV may be dama- ged even if it is switched off.
5 Turning on with the ON/OFF key Before turning on a cold TV in a warm room, first allow any condensation mist that may have formed on the screen to evaporate.
6 2. Programme selection 1. Select programme position 2 (only the first 9 programme positions in the station table are occupied) 4. Next programme You can step sequentially through the programme positions with the keys.
7 2. Programme selection 9-PRG Programme scanning 1. Call 9-PRG. programme scanning 2. Next 9 programmes 3. Select a programme position (e.g. NTV) 4. Return to the original programme position ZDF ARD .
? return OK P + + - AV --/- - P 123 456 789 0 A B TV ? MENU Operator help Switch set on/off Prog select Next programme Basic video/audio settings Sound interrupt Change vol.
3. Presetting TV stations In the sub-menu Standard , you can select the colour and/or the transmission standard. The TV set normally recognises the colour stan- dards (PAL, SECAM, NTSC) automatically, but the transmission standard must always be set manually.
Press this key on the remote control.... The screen displays Explanation 4. Store the setting and return to TV picture TV picture Prog Logo Chan./Freq . Signal ▲▼ >> weitere Einstellungen Std, Pict., Sound 696+03A-GB LOGIC ARD ZDF SA T 1 00 06 34 40 Video Rec.
3. Presetting TV stations Autostore function, sorted to countries The autostore function automatically scans through the entire reception range to locate stations. The located stations are presented in the station table and can then be stored by way of the key.
3.1 Sorting stations In the „Sort“ submenu you can move, exchange, copy, or delete the stationss stored in the programme positions. The „Sort“ submenu is displayed automatically after the autostore function has found all available stations.
Press this key on the remote control.... The screen displays Explanation 13 3.2 Fine tuning The individual channels are automatically tuned to channel centre for station tuning. As a rule, this automatic tuning will be sufficient. Apply manual fine tuning if automatic tuning does not produce satisfactory results.
Press this key on the remote control.... The screen displays Explanation TV picture 14 3.3 Allocating a station logo A logo of up to 8 characters is provided for each station via the VPS signal. The station RTL 2, for example, receives the logo RTL 2.
4. Changing individual picture settings 15 Note: The on-screen display (OSD) can be switched on and off: see page 20, item 8. All settings modified in this menu can be stored by calling the „Video standard values“ or „Audio standard values“ menu respectively and pressing the key.
Press this key on the remote control.... The screen displays Explanation 16 4.2 Adjusting the video and audio standard v alues 1. Call the TV menu 2. Example 1: Call the „Video standard values“ sub- menu. Adjust and store the sharpness. 3. Example 2: Call the „Audio standard values“ sub- menu.
Press this key on the remote control.... The screen displays Explanation 17 5. Equipment configuration Assigning the function keys The remote control handset has three factory programmed function keys A, B and C . Press the key in normal television mode to reveal the factory programming.
Press this key on the remote control.... The screen displays Explanation 18 5. Equipment configuration Assigning the function keys 4. Select the function for TV mode (in this example „Subtitles“) 5. Switch to Hi Text mode and program the function keys 6.
Press this key on the remote control.... The screen displays Explanation 19 5. Equipment configuration Settings for programme change 2. Call the settings for programme change 3. Set spatial sound when changing programmes 4. Select stereo wide when changing programmes OK P + + - AV --/- - P 123 456 789 0 A B TV ? MENU Prog.
Press this key on the remote control.... The screen displays Explanation 20 OK P + + - AV --/- - P 123 456 789 0 A B TV ? MENU Equipm. configuration 696+05H-GB ? MENU return Help TV picture store ? OK Permanent display: c lock Luminance display: 3 OSD setting indic.
21 OK TV 5. Equipment configuration Sound settings You must change the settings in the menu „Sound settings“ if your TV set is connected to a HiFi system or if you wish to compensate for the varying sound volumes of different stations. Audio sockets via which the TV set can be connected to a HiFI system are provided on the rear of the set.
Press this key on the remote control.... The screen displays Explanation 22 Programme Std Pict. ▲▼ << weitere Einstellungen Logo, Channel, Signal 696+06A-GB LOGIC ARD ZDF SA T 1 Auto.
23 Press this key on the remote control.... The screen displays Explanation Programme Std Pict. ▲▼ << weitere Einstellungen Logo, Channel, Signal 696+06C1a-GB VTR1 ARD ZDF SA T 1 Auto. Auto. Auto. Auto. Auto. Auto. Auto. Auto. Auto. Auto. 0 1 2 3 4 5 6 7 8 9 — — — — Sound — — — — Sharpn.
Press this key on the remote control.... The screen displays Explanation 24 Programme Std Pict. ▲▼ << weitere Einstellungen Logo, Channel, Signal 696+06G-GB LOGIC ARD ZDF SA T 1 Auto. Auto. Auto. Auto. Auto. Auto. Auto. Auto. Auto. Auto. 0 1 2 3 4 5 6 7 8 9 — — — — Sound — — — — Chrom.
Press this key on the remote control.... The screen displays Explanation 25 The copy operation with the selected devices is now active. If any subsequent switching operations could interfere with copying, a warning box with the text „AV recor- ding“ will be displayed and the requested switching operation will not be executed.
Press this key on the remote control.... The screen displays Explanation 26 7. AV recording Video recorder ➜ video recorder Example: You wish to copy a film from video recorder 2 to the logic video recorder. 1. Call the AV menu 2. Select the desired AV device (in this example: video rec.
Press this key on the remote control.... The screen displays Explanation 27 Switch-on time: Switch-off time: Reminder time Time of day: OK P + + - AV --/- - P 123 456 789 0 A B TV ? MENU Time settings.
28 Press this key on the remote control.... The screen displays Explanation 4. Enter the reminder time (Example: 21.45 hr) 5. Enter the time manually (Example: 14.
Press this key on the remote control.... The screen displays Explanation 29 Time settings Childlock Timer recording Basic setting of MVS OK P + + - AV --/- - P 123 456 789 0 A B TV ? MENU Timer/childlock 696+08F-GB ? MENU return Help TV picture 8.1 Childlock Switching on Your TV set can be protected against unauthorized use.
TV -Bild 30 Press this key on the remote control.... The screen displays Explanation 4. Enter your personal code 5. Enter the beginning and end of the viewing period Call the TV menu and enter your personal code AV OK P + + - AV --/- - P 123 456 789 0 A B TV ? MENU Childlock 696+08I-GB 01 02 05 -- -- -- : -- -- : -- Childlock.
Press this key on the remote control.... The screen displays Explanation 31 Imissione data 1 1.12 14:20 696+08K-GB Prog Date VPS — — — — — — — — — — : : : : : : : : : : : : : : : : : : : : Timer recording .
32 9. Connecting headphones Headphones can be connected to the TV by way of the connecting socket underneath the fascia cover at the front. The socket will only accept headphones with a 3.5 mm (Carat/Stratos 6.3 mm) jack plug. We recommend the use of headphones with an impedance of at least 32 Ohms.
33 The Hi Text file displays all the subjects available on a specific programme position and the chapters belonging to the currently selected subject. The range of subjects and chapters depend on the transmitting station and can therefore be completely different in each programme position.
34 This function enables you to run through the individual pages. Just as in a book, you can leaf forwards or backwards from the displayed page. Press the right side of the key to step backwards, and the left side of the key to step forwards. This function enables you to run through the individual chapters.
35 Multiple pages are indicated by a dark bar with the subpage numbers on the left-hand side of the display- ed page. The bright numbers indicate the number of subpages contained in this multiple page. The number of sub- pages is transmitted by the stations at intervals of 20 seconds.
36 10. Hi T ext 10. Hi T ext Press this key on the remote control.... The screen displays Explanation Direct page selection Return to last index page After depression of the first numeric key, the num- ber of this key, followed by two hyphens, appears at the top left of the screen.
37 When the B * key is pressed for the first time, the upper part of the selected page is displayed with the font size doubled. You can scroll slowly through the page by holding down the key.
38 There will be certain Hi Text pages, e.g. stock market, news, weather forecast, etc., that you willl want to read repeatedly. We have pro- grammed a way of making it easier to read such pages: Hi Text pages can be flagged with the aid of marks (similar to tabs in a file).
39 When the required page is displayed (in our example page 589), press the red key again to set the second mark. „MARK 2“ is now displayed at the top left-hand corner of the screen. 10 marks can be set on each programme position, as long as the total number of marks assigned does not exceed 100.
40 After the A or B key has been pressed, a panel with „Mark 1“ will be displayed. On programme positions without a mark, a white field will be displayed with the text „No mark“. Each time the A or B key is pressed, you advance to the next mark.
41 Press the A* or B key to call the page where the mark is to be erased. * Depending on how the function keys are program- med. The factory setting is A .
42 The teletext transmitted by the station is superim- posed on the picture at the bottom of the screen. The subtitle function can be activated or deactivated with the A*, B* or C* function key. This TV enables you to display programme subtitles automatically.
43 Press this key on the remote control.... The screen displays Explanation 11. Special picture effects 1. Switch on the zoom function and enlarge the picture 2.
44 Call this function and return to the normal picture Adjusting the slow-motion delay 11. Special picture effects Slow-motion Slow-motion delay * * A or or B C * Call this function and return to the normal picture Before the 9x multipicture function can be used, it must be programmed as a function in the menu „Function keys“.
45 11. Special picture effects Still picture The current frame is „frozen“ on the screen when you press the II key. The TV programme (or the video film) continues to run in the backgro- und. Pressing the II key again switches back to the current programme (or video film).
46 y Euro 1/2/3-socket: Video recorder Camcorder Photo-CD etc. Front sockets: Camcorder Video recorder PIP picture Terrestrial or cable TV Terrestrial or cable TV External devices via Euro sockets 1/2.
47 2. Changing the programme position 1. Calling the PIP picture 3. Swapping the pictures 4. Changing the size and position of the PIP picture 5. Turning off the PIP function When you press the red key, the small picture appears and displays the same programme as the large picture.
48 12. PIP function Monitoring with a video camera The following example shows how you can monitor another room with a camcorder (video camera) while watching a TV programme. Connect the camcorder to the TV set as described on Page 51 of the Operating Instructions for your TV.
49 13. Operation without remote control You can control the following functions on the TV without the remote control handset. The preselection of the function is valid for 10 seconds, only 5 of which are shown in the permanent dis- play. Programme selection: Press the - + keys.
50 14. Remote control handset for video recorders RD1 1 12 3 45 6 78 9 0 OK P + P - AV TV ? MENU + - VTR ɚ ıı ľľ REC TIMER B A ı ı ľľ ıı 10 0 H z R PIP C MUL TI-PRG.
51 15. Connecting peripheral equipment Video recorders can be connected to the TV set via the antenna socket or one of the EURO sockets. We recommend that you use one of the EURO (Scart) sockets for this purpose, since only the EURO sockets have separate inputs and outputs for pictu- re and sound signals.
52 Example 1: You want to connect an S-VHS video recorder with Data Logic to your TV set. You also want to be able, from time to time, to copy recordings from an S-VHS camcorder to the S-VHS video recor- der. Connections: • Connect the S-VHS video recorder with Data Logic via a fully wired Scart cable to the Euro 1 socket of the TV set.
53 15. Connecting peripheral equipment Connecting external devices In the menu „Device connection“, you can define which AV devices are connected to the various sockets on the TV set. The box „Devices“ contains a list of common AV devices. Only certain devices can be connected to the FRONT sockets.
54 The picture quality of a video film can be impro- ved in a terrestrial programme position with a standard channel. The video signal for this programme position must be set to „Aerial“. To ensure optimum picture quality the „VCR“ function must be switched on.
55 15. Connecting peripheral equipment V ideo recorders V ideo signal In the following example, logic video recorder is to be connected to the EURO 1 socket.
EURO EURO 56 15. Connecting peripheral equipment Pay-TV decoder This Pay-TV decoder decodes the scrambled signals of a Pay-TV station (e.g. Premiere) so that they can be displayed on the screen of the TV set. For connection of a Pay-TV decoder, you need a EURO (=Scart) cable in which all 21 pins are assigned.
57 15. Connecting peripheral equipment P ay-TV decoder V ideo signal Press this key on the remote control.... The screen displays Explanation 1. Select the Pay-TV program- me position and call the station table 2. Call the submenu „Signal“ 3. Select video signal „via decoder“ 4.
58 16. T echnical data 16.2 Maintenance and care 16.1 Upgrade kits • SAT upgrade kit 081 NB 1010 For satellite reception without an additional receiver. • SAT upgrade kit 082 NB 1014 SAT receiver to replace the terrestrial receiver. • SAT upgrade kit 083 NB 1018 A SAT receiver.
59 2-channel sound transmission: Separate reproduction of 2 sound channels, e.g. 2 different languages. AF mode Defines the manner in which the audio signals are processed. Audio Latin for „I hear“ - The sound frequency range audible to the human ear is between 60 to 20,000 Hz approx.
60 Press this key on the remote control.... The screen displays Explanation NEX TV IEW is an electronic programme magazine for all important TV stations. It is transmitted by various stations and also contains the programme information for other stations.
61 The message shown in the picture in the centre column appears for all programme positions on which NEXTVIEW information is received. Your TV set displays this message in order to ask whether this programme position is to be used for collecting the NEXTVIEW data.
62 If all available data have been collected, the NEXTVIEW programme magazine is displayed when you press the C key and shows which pro- gramme is being transmitted at the moment by the station on this programme position.
63 Pressing the white key causes the programme magazine to be sorted by the selected subjects. 18. Using NEX TV IEW 1. Select subjects 2. Sort the programme maga- zine by subjects Preview Sort T oday .
64 Open the NEXTVIEW programme magazine and select the programme to be recorded with the keys. If you have a VCR connected: - switch on the VCR. - Press the red key on the remote control of your TV.
65 What is Data Logic? Until now, your TV set and your video recorder were two separate and independent devices. With the new "Data Logic", we have created a dialogue system with which the TV set and the video recorder can exchange data.
20. Index 9 x multipicture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 A ccess to riddle solution (Hi Text). . . . . . . . . . . . . . . . . . . . 42 Aerial connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67 Backlight on the TV set In rare, exceptional cases, the backlight remains off when switched on with the key. The reason for this is that the protective circuit has cut off the current to the lamp. If this happens, and if you have pressed the key several times, you do not know whether the backlight is switched on or off.
TV . VIDEO. AUDIO. MEC ABLITZ Metz. Always first class. Videorecorder Camcorder DVD Audio mecablitz Quality – A matter of principle. With the trend-setting Metz technology you will allways make the correct choice. See your Metz dealer. He will be happy to demonstrate the current Metz range.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Metz Spectral-MF PIP 72 TF 80 - 100 HT, Astral-MF PIP 72 TF 81 - 100 HT, Taros-MF PIP 72 TF 82 - 100 HT, Carat-SF 72 TF 83 - 100 HT, Stratos-SF-PIP 72 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.