Manuel d'utilisation / d'entretien du produit EW1OOR du fabricant Makita
Aller à la page of 17
PUMP MODEL : EW1 OOR INSTRUCTION MANUAL 1 ISSUEEMD-PU0945 I.
Thank you for purchasing a Makita water pump. This manual covers operation and maintenance of water pumps. All information in this publication is based on the latest product infor- mation available at the time of approval for printing. Please read this manual carefully before operating.
~~ ~~ ~ Please make sure you review each precaution carefully. SURROUNDINGS m Operate the pump on a stable, level surface free of small rocks, loose gravel, etc. m Keep pump at least 3 feet (1 meter) away from buildings. Keep pump away from flammables and other hazardous materials (trash, rags, lubricants, explosives).
2. COMPONENTS Speed control lever Plug(priming) Delivery Fuel tank , Chokelever Suction Plug(drain)’ Hose coupling -2-.
3. PREPARATIONS FOR STARTING 1. Connect the suction hose. Use a reinforced-wall or wire braided hose to prevent suction collapse. Since the pump’s self-priming time is directly proportional to hose length, a short hose is recommended. [CAUTION]- = Always use a strainer with the suc- tion hose.
4. Check the prlming water. It is recommended that the water chamber of pump casing should be primed with full of water before operating. +CAUTION]-, Never attempt to operate the pump without priming water or the pump will overheat. Extended dry opera- tion will destroy the mechanical seal.
4. STARTING THE ENGINE 1. Open the fuel cock. 2. Set the speed control lever to “START.” 3. Close the choke lever. If the engine is warm or the ambient temperature is high, close the choke lever half-way, or keep it open fully. If the engine is cold, or the ambient temperature is low, close the choke lever.
4. Pull the starter handle slowly until re- sistance is felt. This is the "compression" point. Return the handle to its original position and pull swiftly. H Do not pull out the rope all the way. H After starting the engine, allow the starter handle return to its original position while still holding the handle.
5. OPERATION Avoid operating the engine at high speed for a long time without load. 1. After starting the engine, gradually open choke by turning the choke lever and finally keep it open fully. Do not fully open the choke lever im- mediately when the engine is cold or the ambient temperature is low, be- cause the engine may stop.
6. STOPPING THE ENGINE 1. Set the speed control lever to the low speed position and allow the engine to run at low speed for 2 or 3 minutes before stopping. 2. Keep depressing the STOP BUTTON until the engine stops. Do not stop the engine suddenly when it is running at high speed.
DAILY INSPECTION lhours (daily) 0 (daily) Clean engine and check bolts and nuts. Clean spark plug. Clean air cleaner. Before running the pump, check the following service items: a Enough fuel. a Excessive vibration, noise. a Clean air cleaner element.
0. "HOW-TO" MAINTENANCE INSPECTING THE SPARK PLUG Clean off carbon deposits on the plug electrode using a plug cleaner or wire brush. w Check electrode gap. Adjust it to between 0.02 and 0.03 inches. (0.6 and 0.7mm) CLEANING AIR CLEANER Remove the element and clean it with kero- sene.
CHECKING BOLTS, NUTS AND SCREWS Retighten loose bolts and nuts. Check for fuel and oil leaks. Replace damaged parts with new ones. Keep safety on your mind. CLEANING FUEL STRAINER w Loosen the banjo bolt from the carburetor and remove the strainer (plastic mesh).
Pump does not run. I Pumping volume is small. -r Pump does not self-prime. Engine does not start. (See page 13.) Sticking of impeller (Disassemble and clean.) Sucking air at suction side (Check piping at suction side.) Drop in engine output (Consult your nearest dealer.
WHEN ENGINE DOES NOT START: fore you take the pump to your Makita dealer. If you still have trouble after com- pleting the checks, take the pump to your nearest Makita dealer. Before testing, carefully wipe off spilled fuel. Put the plug as far away from the spark plug hole as possible.
IO. PREPARATIONS FOR STORAGE Drain all water from the drain plug. [CAUTION m When retightening drain plug, be sure to clean the drain plug and the thread of casing.Otherwise, thread may be damaged. Open the fuel cock to discharge the fuel from the fuel tank.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Makita EW1OOR c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Makita EW1OOR - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Makita EW1OOR, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Makita EW1OOR va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Makita EW1OOR, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Makita EW1OOR.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Makita EW1OOR. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Makita EW1OOR ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
