Manuel d'utilisation / d'entretien du produit 3702B du fabricant Makita
Aller à la page of 23
Tkimmer Collet chuck capacity 14 _~____~__ 1/4” MODEL 3702B Net weight Overall lenqth No load speed (RPMI 28 000 296 mm 11 1 5 8 1 1 6 kg 13 5 lbsl - INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATI.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. 2. Handle the bits very carefully. 3. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 4. Avoid cutting nails.
Installing or removing trimmer bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. To remove the bit, follow the installation procedure in reverse.
Adjusting angle of tool base Loosen the wing bolts and adjust the angle of the tool base (5' per graduation) to obtain the desired cutting angle. - Gradual Wing nut __ Wing bolt ~___ Base It of ring Adjusting amount of chamfering To adjust the amount of chamfering, loosen the wing nuts and adjust the trimmer shoe.
When doing edge cutting, the workpiece surface should be on the left side of the bit in the feed direction. (See the figure below) Feed direction (View from the top of the tool) Correct bit feed Bit revolving direction Feed direction 2w direction NOTE : Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor.
Straight guide The straight guide is effectively used for straight cuts when chamfering or grooving. Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. Loosen the wing bolts and secure the tool base horizontally.
Circular work 0Circular work may be accomplished if you assemble the straight guide and guide plate 0 Min. and max. radius of circles to be cut (distance between the center of circle and the as shown in the figure below. center of bit) are as follows : Min.
Trimmer guide Trimming, curved cuts for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Loosen the wing bolts and secure the tool base horizontally. Install the trimmer guide on the tool base with the clamp screw (A).
Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. Remove the tool base from the tool. Loosen the wing bolts and secure the tool base horizontally. Loosen the two screws on the tool base.
Secure the templet to the workpiece. Place I the tool on the templet and move the tool with the templet guide sliding along the side of the templet. Straight bit I Templet guide Base r I. I Distance (X) Workpiece 10 mm (25/64") L NOTE : The workpiece will be cut a slightly different size from the templet.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes I Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
ACCESS0 R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Bits STRAIGHT -Single Flute HIGH SPEED STEEL PART NO. A E C D E 733232-6A 118 5/16 1-1 18 114 1-518 CARBIDE TIPPED PART NO @ STRAIGHT - 2 Flute A E C D E 733003-2A 3/16 7116 1 318 1 I4 2 733003-EA 5/1.
ROUND NOSE -I& CARBIDE TIPPED PART NO. A a C D E 733008-4A 318 9/16 1-114 1 I4 2 733008-2A 114 15132 1-1 I4 1 /4 1-718 CORE BOX 4DC &, A/- -J f I HIGH SPEED STEEL PART NO. A E C D E 73323a-2~ 114 1 /4 1-3/16 114 1-1 12 VEE GROOVING IDk CARBIDE TIPPED PART NO.
PANEL PILOT HIGH SPEED STEEL PART NO. A B C D E 733236-0A 114 314 1 114 2-7116 CORNER ROUNDING CARBIDE TIPPED - Ball Bearing Pilot 733120 OA 7/8 112 318 1 114 114 115116 3/16 7331 20 2A 112 1 114 114 .
ROMAN OGEE CARBIDE TIPPED - Ball Bearing Pilot I PARTNO. AI A? B C 0 E RI 5132 I 733123-2A 1 3/8 15/32 1-1/4 1/4 REPLACEMENT BEARING - NO, 733132-2A FLUSH TRIMMER -Self Piloting SOLID CARBIDE PART NO. A B C D E 7331 28-OA 1 /4 1 I4 1-1/16 114 1-9/16 7" BEVEL TRIMMER - Self-Piloting SOLID CARBIDE PART NO.
COMB1 NATION F LUSH/2Z0 BEVEL TRIMMER SDC CARBIDE TIPPED 733128-6A 7/16 112 3/16 1-1/4 1/4 1-314 3 FLUTE FLUSH TRIMMER ASSEMBLY -Self Piloting -I uc SOLID CARBIDE CUTTER I PARTNO.
3 FLUTE 22" BEVEL REPLACEMENT CUTTER LA4 SOLID CARBIDE I PARTNO. A B D I 733129-8A 718 3/8 1 /4 FOR BEVEL TRIMMER ASSEMBLY NO, 733129-4A 114" REPLACEMENT ARBOR PART NO A B C D E 733131,2A 5/8 3/8 1-114 1 /4 2 318 FOR FLUSH TRIMMER ASSEMBLY NO 733129-2A AND NO 733129-4A BALL BEARING PILOT Dl Dz PART NO.
Apr 06 ‘89 US 114” TRIMMER Model 3702B Note The switch, noise suppressor and other part conflguratlons may differ from country to country.
MODEL 37028 ;:, DESCRIPTION Apr 04 '89 US 'k,'o" ,"., DESCRIPTION MACHINE ~ 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 1 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 2 2 1 2.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool IS thoroughly inspected and tested before leaving the factory. It IS warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Makita 3702B c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Makita 3702B - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Makita 3702B, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Makita 3702B va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Makita 3702B, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Makita 3702B.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Makita 3702B. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Makita 3702B ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
