Manuel d'utilisation / d'entretien du produit VRZ362AT du fabricant Magnavox
Aller à la page of 64
Owner’s Manual Important! Return your Warranty Registration Card within 10 days. See why inside. POWER VIDEO L AUDIO R VCR/TV CHANNEL REC/OTR PAUSE PLAY REW STOP/EJECT F.
Once your PHILIPS MAGNAVOX purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Features • Auto DBS RecordLink™ • Automatic Channel Setup • Automatic Clock Setting With Time Zone • Automatic Head Cleaner • Automatic Operation Features • Automatic Trac.
4 Table of Contents Setting Up Your VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
● Use only tapes with the mark. ● Remove any light adhesive stick-on notes from the video cas- sette tape before putting the tape in the VCR. Removable labels can jam the VCR. ● Periodic maintenance is required to maintain your VCR’s excel- lent performance.
CH3 CH4 OUT IN ANT OR AUDIO R L VIDEO OUT IN IN OUT CH3 CH4 OUT IN ANT R L VIDEO IN OUT IN OUT AUDIO 75 V ANT / CABLE OR 75 V ANT / CABLE 6 Hookups Without a Cable Box / Direct Broadcast System The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below.
CH3 CH4 OUT IN ANT CH 4 or CH 3 CH3 / CH4 Switch AUDIO R L VIDEO OUT IN IN OUT CH3 CH4 OUT IN ANT CH3 CH4 R L VIDEO IN OUT IN OUT AUDIO CH3 CH4 OUT IN ANT 75 V ANT / CABLE 75 V ANT / CABLE CH3 CH4 OUT.
8 Hookups With a Cable Box / Direct Broadcast System There are two ways to connect your Cable Box/DBS to the VCR. With this connection: ● You may view any channel. ● You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR.
Hookups With a Cable Box / Direct Broadcast System (cont’d) 9 R L VIDEO IN OUT IN OUT AUDIO CH3 CH4 OUT IN ANT IN OUT 75 V ANT / CABLE With this connection: ● You may watch one channel while recording another. ● You may not record scrambled channels.
10 Hookups With a Stereo TV R L VIDEO IN OUT IN OUT AUDIO CH3 CH4 OUT IN ANT antenna or cable to ANT(enna) IN Jack Video Cable Audio Cable VIDEO (yellow) and AUDIO (red and white) OUT Jacks Audio and Video IN Jacks on TV ● Audio and Video cables are not supplied.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH REC END SKIP EJECT MENU CLEAR PAUSE/STILL 1 Press the VCR button, then press the POWER button.
12 Automatic Channel Setup 2 Press the MENU button . SELECT op CHOOSE B → PROGRAM VCR SET UP TUNER SET UP SET CLOCK REMOTE LOCATOR TO END PUSH EXIT • You can not enter the TUNER SET UP menu when you are in Line Input mode (channel 001 or 002). When you select channel 001 or 002, AV REAR or AV FRONT will appear on-screen briefly.
Automatic Channel Setup (cont’d) 13 Adding/Deleting Channels 2 Press the MENU button . SELECT op ADD/DELETE B 124 DELETED 125 DELETED 1 → DELETED 2 ADDED 3 ADDED TO END PUSH EXIT 3 Press the PLAY/ o button or the STOP/ p button to select TUNER SET UP, then press the F.
14 Automatic Channel Setup (cont’d) Reviewing Memorized Channels 4 Press the PLAY/ o button or the STOP/ p button to select CH MEMORY REVIEW, then press the F.FWD/ B button. A list of programmed channels will appear on-screen. ● If all the programmed channels don’t fit on the screen, press the F.
Setting the Clock 15 2 Press the MENU button . There are two ways to set the clock. With manual clock setting, you tell the VCR the current time. With automatic clock setting, the VCR gets the current time from your local PBS station. It keeps track of the time by constantly referring to the time broad- casted by your PBS station.
TIME 02 :15 PM MONTH – – / – – /– – TO CORRECT PUSH CLEAR TO END PUSH EXIT TIME 02 :15 PM DATE 07/ 01 / 98 WED. TO CORRECT PUSH CLEAR TO END PUSH EXIT 5 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM.
Setting the Clock (cont’d) 17 4 ● If you want the VCR to locate a local PBS station from which to take the time, press the PLAY/ o button or the STOP/ p button to select SET PBS CH. AUTO. Then press the F.FWD/ B button. When the current time appears on-screen, you’re finished.
18 Setting the Clock (cont’d) Time Zone When using the AUTO CLOCK function, you can specify a time zone in which a local PBS channel is located. That way, the VCR will update the clock according to your time zone. 1 Press the VCR button, then press the MENU button .
2 Press the MENU button. 3 Press the PLAY/ o button or the STOP/ p button to select SET CLOCK, then press the F.FWD/ B button. 5 Press the STATUS/EXIT button.
20 Language Selection 2 Press the MENU button . Follow the steps below to change the language of the on-screen displays. 3 Press the PLAY/ o button or the STOP/ p button to select VCR SET UP, then press the F.FWD/ B button. 4 Press the PLAY/ o button or the STOP/ p button to select LANGUAGE, then press the F.
Setting the Remote to Operate a TV 21 • The remote control may only operate some features of your TV. For exam- ple, the remote control may turn on the TV power, but it may not change channels at the TV.
• The remote control may only operate some features of your Cable Box or DBS. For example, the remote control may turn on the Cable Box or DBS power, but it may not change chan- nels at the Cable Box or DBS.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH RE.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH REC END SKIP EJECT MENU CLEAR PAUSE/STILL PAUSE/STILL Button While recording, press to pause the recording.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH REC END SKIP EJECT MENU CLEAR PAUSE/STILL Remote Control Buttons (cont’d) 25 STOP/ p Button Press to stop the tape.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH RE.
SELECT op CHOOSE B → STATUS [ON] COUNTER ONLY [OFF] TO END PUSH EXIT On-Screen Status Displays 27 • If the channel you select has no broadcast, the screen will become solid blue. • You may not access a status display when viewing a still picture, during slow motion playback, or when the F.
28 VCR Display Panel Cassette Compartment Insert a tape here. POWER VIDEO L AUDIO R VCR/TV CHANNEL REC/OTR PAUSE PLAY REW STOP/EJECT F.FWD VCR REC PWR. PM w VCR Light This light appears when the VCR is in VCR posi- tion. This light does not appear when the VCR is in TV position.
Front Panel 29 PAUSE Button While recording, press to pause the recording. Press again to resume recording. Details are on page 32. You can not pause a One-Touch Recording. During tape playback, press to freeze the picture. Press again to resume playback.
AUDIO IN Jacks Connect cables coming from the AUDIO OUT Jacks of a camcorder, another VCR, or an audio source here. Details are on page 44. VIDEO IN Jack Connect a cable coming from the VIDEO OUT Jack of a cam- corder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.
Playing 31 • If the tape you want to play is already in the VCR, make sure the VCR power is on and the VCR is in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button.) Press the VCR button, then press the PLAY/ o button.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH REC END SKIP EJECT MENU CLEAR PAUSE/STILL Read and follow the steps below to record a television program.
2 Start a recording. (See page 32.) Recording One Channel/Watching Another 33 • If your VCR remote control does not operate your TV, see page 21 for details. • If you use a Cable Box or Direct Broadcast System hookup, you may not be able to watch one channel while recording another.
34 One-Touch Recording 2 Press the CH(annel) o / p buttons or the Number buttons to select the channel you want to record. OTR (0:30) CH12 3 Press the REC(ord)/OTR button repeatedly until the desired recording length (30 minutes to eight hours) appears on-screen.
DAILY PROGRAM (MON-FRI) PROGRAM -1 2 3 4 5 6 7 8- SELECT PROGRAM NUMBER TO END PUSH EXIT Timer Recording 35 Follow the steps below to program your VCR to record TV pro- grams while you’re away from home. The VCR will turn itself on, record, and turn itself off automatically.
ONE TIME PROGRAM PROGRAM 1 CHANNEL – – TO CORRECT PUSH CLEAR TO END PUSH EXIT ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON – – : – – TO CORRECT PUSH CLEAR TO END PUSH EXIT 6 Press two Number buttons for the hour you want the recording to begin.
ONE TIME PROGRAM PROGRAM 1 CHANNEL 10 TIME ON 09:30 PM TIME OFF 11:00 PM REC SPEED SLP SP=1 LP=2 SLP=3 TO CORRECT PUSH CLEAR TO END PUSH EXIT Timer Recording (cont’d) 37 8 Press the Number 1 button to record in SP speed, the Number 2 button to record in LP speed, or the Number 3 button to record in SLP speed.
38 Timer Recording (cont’d) 6 Repeat steps 1 - 4 to make sure you have cleared the cor- rect timer recording. • CLASH may flash on-screen when you finish setting a timer recording. This means that the timer recording you just programmed and another timer recording overlap.
Auto DBS RecordLink 39 If you connect your VCR to a satellite tuner that has the Electronic Program Guide, the VCR will turn itself on, record, then turn itself off. First, read the owner’s manual of your satellite tuner; then, follow these steps to set up your VCR.
40 Setting Up the VCR Plus+ Programming System 1 First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR Plus+ programming system to work properly.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH RE.
VCR PLUS+ PROG. PLUS CODE : – – – – – – – – TO END PUSH EXIT 42 Timer Recording With the VCR Plus+ Programming System Follow these steps to set a timer recording with the PlusCode programming numbers in your TV guide. Before you begin: ● Set up the channels at the VCR (page 12).
Timer Recording With the VCR Plus+ Programming System (cont’d) 43 • If the time for a timer recording comes up during a One-Touch Recording, the OTR has priority. • To stop a started timer recording, press the STOP/EJECT button on the VCR. • If the power fails for more than one minute, programmed timer record- ings may be lost.
1 Make the connections shown above. 44 Rerecording (Tape Duplication) 3 VCR 2 will record your tape. Insert a blank tape in VCR 2. The VCR must be in VCR position. (The VCR light will appear on the display panel. If it does not, press the VCR/TV button once.
Repeat Play 45 Follow the steps below to make the VCR play a tape over and over. 2 Press the MENU button. 3 Press the PLAY/ o button or the STOP/ p button to select VCR SET UP, then press the F.FWD/ B button. 5 Press the F.FWD/ B button so that ON appears beside REPEAT PLAY.
VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH RE.
Index Search 47 This feature allows you to index the starting points of programs that you have recorded on a tape. Then, you can easily rewind or fast forward to that point. Example: If you are watching program number 4 and you want to fast for- ward to program number 7, skip three programs.
48 Record End Search/Skip Search Record End Search This function enables you to search forward to an unrecorded portion of the tape (or to the point at which recording was stopped). Make sure the tape is fully rewound. 1 Press the REC(ord) END SEARCH button.
Quick Search 49 The Quick Search feature locates the beginning of each recording on a tape, then plays the first portion of the recording at high speed for 30 seconds. After it plays the portion, the VCR fast for- wards the tape to the next recording.
50 Real-Time Counter Memory • The MEMORY button does not function if REPEAT PLAY is set to ON. Details are on page 45. • To erase a real-time counter memo- ry, press the MEMORY button until the M disappears from the screen. • You may only set the real-time counter to zero at one location at a time.
Special Effects Playback 51 Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/ B button or the REW(ind)/ { button. A fast forward or reverse picture search will begin. 2 To return to playback, press the PLAY/ o button.
52 Special Effects Playback (cont’d) Viewing a Slow Motion Picture 1 During tape playback, press the SLOW button . The tape will play in slow motion.
Automatic Operation Features 53 The following playback features will always operate. Automatic Playback When you put a tape in the VCR, the power will come on auto- matically.
54 Multi-Channel Television Sound System Your VCR can play recordings broadcast in Hi-Fi (high fidelity) stereo, which produces a crisp, clear sound from two sources. Your VCR also can play tapes recorded in a second audio (usually, that means your program is recorded in a second language).
Multi-Channel Television Sound System (cont’d) 55 1 Press the VCR button, then press the MENU button. 2 Press the PLAY/ o button or the STOP/ p button to select TUNER SET UP, then press the F.FWD/ B button . 3 Press the PLAY/ o button or the STOP/ p button to select TV STEREO or 2ND AUDIO.
1 VAR.SLOW VCR TV CBL/DBS VOL. CH. MUTE +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV VCR/TV REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY X2 PLAY SLOW VCR PLUS+ /ENTER QUICK TIME INDEX SEARCH REC END SKIP EJECT MENU CLEAR PAUSE/STILL 56 Hi-Fi Stereo Sound System 1 Press the VCR button, then press the MENU button.
Hi-Fi Stereo Sound System (cont’d) 57 6 Press the MENU button. 7 Press the PLAY/ o button or the STOP/ p button to select TUNER SET UP, then press the F.FWD/ B button . 8 Press the PLAY/ o button or the STOP/ p button to select TV STEREO. Then, press the F.
If you are having problems with your product, check this list of problems and possible solutions before requesting service. You may be able to solve the problem yourself. If you need to call a customer service representative, please know the model number and serial number of your product before you call.
TV programs cannot be watched normally. • Put the VCR in TV position. (Press the VCR/TV button so that the VCR light disappears from the display panel. For details see page 29.) • Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if applicable).
60 Glossary AUDIO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record audio from another source (IN) or to send audio to another source (OUT). Automatic Channel Setup: process in which the VCR memo- rizes all available channels.
Specifications 61 Video Heads Four heads – Hi-Fi Video Signal EIA standards; NTSC color Antenna VHF/UHF – 75 ohm external antenna terminal VHF Output Signal Channel 03 or 04 (switchable) 75 ohms u.
VIDEO CASSETTE RECORDER 90 Days Free Labor/One Year Parts Exchange. This product must be carried in for repair. WHO IS COVERED? You must have proof of purchase to receive warran- ty service. A sales receipt or other document show- ing that you purchased the product is considered proof of purchase.
ac power cord .................................30 accessories .......................................64 ant(enna) in jack ...................6-10, 30 audio in/out jacks .......10, 29, 30, 44 auto dbs recordlink ........................39 automatic playback .
IB8052E001 Printed In China 0VMN02090 / H1940UD * * * * * S UPPLIED A CCESSORIES Remote Control 4835 218 37229 Three AA Batteries 4835 138 17012 RF Coaxial Cable, 75 ohm 4835 323 27011 Check to be sure the items on this page are packed with your VCR. These accessories are provided to help you use or set up your VCR.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Magnavox VRZ362AT c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Magnavox VRZ362AT - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Magnavox VRZ362AT, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Magnavox VRZ362AT va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Magnavox VRZ362AT, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Magnavox VRZ362AT.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Magnavox VRZ362AT. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Magnavox VRZ362AT ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
