Manuel d'utilisation / d'entretien du produit V200 du fabricant Lenovo
Aller à la page of 126
Le n o v o 3 000 V1 00 an d V2 00 Hard w ar e M ain t e n a n c e Ma nu a l May 2007 This manual supports: Lenovo 3000 V100 and V200 (MT 0763 and 0764).
.
Le n o v o 3 000 V1 00 an d V2 00 Hard w ar e M ain t e n a n c e Ma nu a l.
Note Before using this information and the pr oduct it supports, be sure to r ead the general information under “Notices” on page 1 17. First Edition (May 2007) © Copyright Lenovo 2007. All rights reserved. U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services ar e provided with RESTRICTED RIGHTS.
Contents Introduction . . . . . . . . . . . . .1 About this manual . . . . . . . . . . . .1 Important service information . . . . . . . .1 Strategy for replacing FRUs . . . . . . . . .1 Strategy for replacing a har d disk drive . . . .2 Important notice for replacing a system boar d .
iv MT 0763 and 0764.
Introduction About this manual This manual contains service and refer ence information for Lenovo 3000 V100 and V200 (MT 0763 and 0764). Use this manual along with the advanced diagnostic tests to troubleshoot pr oblems.
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue . v Some computers have both a processor boar d and a system board.
Using PC Entitlement W arehouse (PEW) v PEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities for CMV products at a MT - serial number level. An example of key commodities are har d disk drives, system boards, micropr ocessors, Liquid Crystal Displays (LCDs), and memory .
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry . RoHS requirements must be implemented on Lenovo products placed on the market after June 2006.
Diskette compatibility matrix The compatibility of each of the drives with the diskettes for it is as follows: Diskette drive Diskette capacity Compatibility 3.
Safety notice 2 D ANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery , recharge it, throw it into fire or water , or short-circuit it. Dispose of the battery as required by local ordinances or regulations.
Safety notice 3 D ANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water , or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Safety notice 4 D ANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector , disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water . Dispose of the battery as required by local ordinances or regulations.
Safety notice 5 Safety notice 6 D ANGER If the LCD breaks and the fluid fr om inside the LCD gets into your eyes or on your hands, immediately wash the affected ar eas with water for at least 15 minutes. Seek medical care if any symptoms fr om the fluid are present after washing.
Safety notice 7 D ANGER Safety notice 8 D ANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials.
Safety information The following section presents safety information with which you need to be familiar before you service a Lenovo 3000 computer . General safety Follow these rules to ensur e general safety: v Observe good housekeeping in the area of the machines during and after maintenance.
Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electr ostatic discharges.
v Do not service the following parts with the power on when they are r emoved from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures corr ect grounding of the units.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electr ostatic discharge (ESD.) ESD damage can occur when there is a dif ference in charge between objects.
Laser compliance statement Some models of Lenovo 3000 computer are equipped fr om the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: D ANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
General descriptions The descriptions in this chapter apply to any Lenovo 3000 model that has the PC-Doctor ® for DOS diagnostics program. Some descriptions might not apply to your particular computer . Read this first Before you go to the checkout guide, be sur e to read this section.
Following is a list of some common items that are not cover ed under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Related service information This section provides information about the following: v “Service We b site” v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on.
9. When prompted, insert the appr opriate Product Recovery disc and then click OK . The second phase of the recovery pr ocess begins. 10. When all of the data has been copied from the last Pr oduct Recovery disc in the set, a message is displayed prompting you to r estart the computer .
How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If an SVP is not known by the servicer: 1. T urn off the computer . 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 46.
10. Select Ye s in the Setup Configuration window . Both user HDP and master HDP will have been removed. Power management Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and hibernation.
To cause the computer to enter hibernation mode, do any of the following: v Press the Fn+F12 keys. v If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action.
Checkout guide Use the following procedur es as a guide in identifying and correcting problems with the Lenovo 3000 computer . Note: The diagnostic tests are intended to test only Lenovo 3000 pr oducts. The use of non-Lenovo 3000 products, pr ototype cards, or modified options can lead to false indications of errors and invalid system r esponses.
To run the test, do as follows: 1. Insert the PC-Doctor disk into the diskette drive; then power on the computer . If the computer cannot be powered on, go to “Power system checkout” on page 26, and check the power sources. If an error code appears, go to “Symptom-to-FRU index” on page 36.
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v System Configuration v Memory Contents v Physical Disk Drives v Logical Disk Drives v.
Checking the ac adapter Yo u are her e because the computer fails only when the ac adapter is used. v If the power-on indicator does not turn on, check the power cor d of the ac adapter for correct continuity and installation. v If the computer does not charge during operation, go to ″ Checking operational charging.
Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave it at r oom temperature for a while. After it cools down, reinstall and r echarge it. To check the battery pack, do the following: 1. Power off the computer .
Lenovo 3000 V100 and V200 Product overview . . . . . . . . . . . .3 0 Specifications . . . . . . . . . . . . .3 0 Status indicators . . . . . . . . . . . .3 3 FRU tests . . . . . . . . . . . . . .3 4 Fn key combinations . . . . . . . . . .3 5 Symptom-to-FRU index .
Product overview This section presents the following pr oduct-unique information: v “Specifications” v “Status indicators” on page 33 v “FRU tests” on page 34 v “Fn key combinations” o.
Feature Description Graphic memory chip v Intel 915GM/PM v Intel 945GM v Intel 965GM Display v 12.1-inch wide, 16M colors, WXGA (1280 × 768 resolution) TFT color LCD Standard memory v 256-MB DDR2-667.
Feature Description Internal modem v 56.6 Kbps Audio v Built-in stereo speakers v Software contr ol volume Ethernet (on the system board) v 10/100 Ethernet Mini PCI adapter v Intel PRO W ireless 3945ABG Mini-PCI Expr ess Adapter v Broadcom 802.1 1ag WLAN PCI-E Mini Card v Broadcom 802.
Status indicators The system status indicators show the status of the computer , as follows: 1 2 4 3 5 9 8 7 6 Indicator Meaning 1 Caps lock Caps Lock mode is enabled. Yo u can enter all alphabetic characters (A-Z) in uppercase without pr essing the Shift key .
Indicator Meaning 7 Battery status Green: The battery is charged between 80% to 100% of the capacity , and being discharged between 0% to 80% of the capacity . Blinking green: The battery is charged between 20% to 80% of the capacity , and being charged.
Fn key combinations The following table shows the function of each combination of Fn with a function key . Key combination Description Fn+F1 V olume down. Fn+F2 V olume up. Fn+F3 Reserved. Fn+F4 Put the computer in sleep (standby) mode. To return to normal operation, press the Fn key only , without pressing a function key .
Symptom-to-FRU index The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or action, in sequence.
Symptom or error FRU or action, in sequence 0260 System timer error 1. Charge the backup battery for more than 8 hours by connecting the ac adapter . 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 3. System board.
Error messages Symptom or error FRU or action, in sequence Unsupported memory . DIMM . Make sur e to use supported memory . Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility . 2. Backup battery . 3. System board. Allocation error for device.
No-beep symptoms Symptom or error FRU or action, in sequence No beep, power-on indicator on, LCD blank, and no POST . 1. Make sure that every connector is connected tightly and correctly . 2. DIMM. 3. System board. No beep, power-on indicator on, and LCD blank during POST .
LCD-related symptoms Important The TFT LCD for the notebook computer contains many thin-film transistors (TFT s). The presence of a small number of dots that ar e missing, discolored, or always lighted is characteristic of TFT LCD technology , but excessive pixel problems can cause viewing concerns.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardwar e defect, such as cosmic radiation, electrostatic discharge, or softwar e errors. FRU replacement should be consider ed only when a problem r ecurs.
FRU replacement notices This section contains notices related to r emoving and replacing parts. Read this section carefully befor e replacing any FRU. Screw notices Loose screws can cause a r eliability problem.
v “Retaining the UUID” v “Reading or writing the ECA information” Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system boar d was loaded with the serial numbers of the system and all major components.
To check what ECAs have been previously applied to the machine, use the ECA Information Read/W rite function on the CE Utility Diskette for Lenovo 3000 notebooks. 1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the computer . 2.
Removing and replacing a FRU This section presents dir ections and drawings for use in removing and replacing a FRU. Be sure to observe the following general r ules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.
1010 Battery pack D ANGER Unlock the battery release lever 1 and holding the battery r elease lever in the unlocked position 2 , remove the battery pack in the dir ection shown by arrow 3 . 1 2 3 Use only the battery specified in the parts list for your computer .
1020 Hard disk drive slot cover and hard disk drive For access, remove this FRU: v “1010 Battery pack” on page 46 Attention v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Impr oper handling can cause damage and permanent loss of data.
4 3 5 When installing: Make sure that the har d disk drive connector is attached firmly . Removing and replacing a FRU 48 MT 0763 and 0764.
1030 DIMM slot cover For access, remove this FRU: v “1010 Battery pack” on page 46 Note: Loosen the screws 1 , but do not r emove them. 1 2 1040 DIMM For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1030 DIMM slot cover” 1 1 2 When installing: Insert the notched end of the DIMM into the socket.
1050 Backup battery D ANGER For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1030 DIMM slot cover” on page 49 1 2 When installing: Make sure that the battery connector is attached firmly . Use only the battery specified in the parts list for your computer .
1060 PCI Express Mini Card slot cover and PCI Express Mini Card for 802.1 1 a/b/g wireless LAN For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 Note: Loosen the screws 1 , but do not r emove them.
1070 PCI Express Mini Card slot cover and PCI Express Mini Card 802.1 1 a/b/g/n wireless LAN For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 Note: Loosen the screws 1 , but do not r emove them.
For MT 0763 4 3 3 4 5 In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arr ow . Step Screw (quantity) Color T orque 4 M2 × 4 mm, pan-head, nylon-coated (2) Silver 0.
For MT 0764 4 3 4 5 In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arr ow . Step Screw (quantity) Color T orque 4 M2 × 4 mm, pan-head, nylon-coated (2) Silver 0.
1080 Optical drive For access, remove this FRU: v “1010 Battery pack” on page 46 3 1 2 Step Screw (quantity) Color T orque 1 M2.5 × 5 mm, pan-head, nylon-coated (1) Silver 0.
1 100 Function board For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1090 Middle cover” on page 55 3 2 1 1 Step Screw (quantity) Color T orque 1 M2 × 4 mm, pan-head, nylon-coated (2) Silver 0.
111 0 Keyboard For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1090 Middle cover” on page 55 1 Step Screw (quantity) Color T orque 1 M2.
2 3 3 4 Lift the keyboard a little in the dir ection shown by arrow 2 . Then unlock the connector 3 and detach the connector 4 . When installing: 1. Make sure that the keyboar d connector is attached firmly . Then lock the connector .
1 120 Hinge covers, keyboard bezel, 5-1 Digital Media Reader card, BDC, and fingerprint reader card For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1060 PCI Express Mini Car d slot cover and PCI Express Mini Card for 802.
Remove the hinge cap L 3a and the hinge cap R 3b . 3b 3a Note: Steps 4 and 5 are only for MT 0763. 5 5 5 4 (continued) Removing and replacing a FRU 60 MT 0763 and 0764.
Release the antenna cables from the cable guides of the frame. In step 6 , take care not to damage the cables when you pull out them fr om the guide hole. 6 7 7 7 When installing: Route the antenna cables along the cable guides. When you route the cables, do not tense them.
8 8 8 8 8 When installing: Make sure that all the connectors ar e attached firmly . 9 9 9 Step Screw (quantity) Color T orque 9 M2.5 × 5 mm, pan-head, nylon-coated (3) Silver 0.
10 11 Removing and replacing a FRU Lenovo 3000 V100 and V200 63.
To remove the 5-1 Digital Media Reader card, do as follows: 1 2 1 a Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, pan-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) 4 3 3 When installing: Make sure that all the connectors ar e attached firmly .
To remove the BDC, do as follows: 1 1 2 3 Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, pan-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connector is attached firmly .
To remove the fingerprint reader car d, do as follows: 2 1 1 1 3 3 3 Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, pan-head, nylon-coated (3) Silver 0.
1 130 LCD unit For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1060 PCI Express Mini Car d slot cover and PCI Express Mini Card for 802.1 1 a/b/g wireless LAN” on page 51 v “1070 PCI Express Mini Car d slot cover and PCI Express Mini Card 802.
4 3 4 5 3 Step Screw (quantity) Color T orque 3 M2.5 × 5 mm, pan-head, nylon-coated (2) Silver 0.392 Nm (4 kgfcm) 4 M2 × 4 mm, pan-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) When installing: Make sure that the LCD connector 5 is attached firmly .
6 6 When installing: When you attach the LCD unit, make sure that you do not pinch the antenna cable. Removing and replacing a FRU Lenovo 3000 V100 and V200 69.
1 140 Heat sink assembly , CPU, MDC, ExpressCard slot, and system board For access, remove these FRUs, in or der: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover and har d di.
4 5 Remove the heat sink as follows: 1 3 2 2 2 Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, pan-head, nylon-coated (1) Silver 0.245 Nm (2.
When installing: Before you attach a new thermal module to the computer , peel off the covering film of thermal gr ease. Then attach the thermal module to the computer .
Remove the CPU as follows: Attention: CPU is extr emely sensitive. When you service the CPU, avoid any kind of rough handling. Rotate the head of the screw in the dir ection shown by arrow 1 to release the lock; then remove the CPU in the dir ection shown by arrow 2 .
Remove the MDC as follows: For MT 0763 1 1 2 Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, pan-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) 4 3 When installing: Make sure that the connector on the underside of the car d is attached to the system board firmly , and then fasten the screws.
For MT 0764 2 3 1 1 Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, pan-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connector on the underside of the car d is attached to the system board firmly , and then fasten the screws.
Remove the ExpressCar d slot as follows: 1 1 1 1 Step Screw (quantity) Color T orque 1 M2 × 2.5 mm, pan-head, nylon-coated (4) Silver 0.245 Nm (2.5 kgfcm) T urn over the system board, and disconnect the Expr essCard slot assembly . 2 When installing: Make sure that the connector is attached firmly , and then fasten the screws.
1 150 Fan and base cover (with speakers) For access, remove these FRUs, in or der: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover and har d disk drive” on page 47 v “1030 DIMM slot cover” on page 49 v “1040 DIMM” on page 49 v “1060 PCI Express Mini Car d slot cover and PCI Express Mini Card for 802.
Note: Applying labels to the bottom cover When you replace the base cover , you need to stick some labels on the new base cover . Some of the labels have been shipped with the new base cover , and some may need to be reused fr om the old base cover .
2010 LCD front bezel For access, remove this FRU: v “1010 Battery pack” on page 46 1 1 1 1 Step Screw cap Screw (quantity) Color T orque 1 M2.
2020 Inverter card For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “2010 LCD front bezel” on page 79 1 4 3 2 1 Step Screw (quantity) Color T orque 1 M2 × 4 mm, pan-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) When installing: Make sure that connectors 3 and 4 ar e attached firmly .
2030 Integrated camera For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “2010 LCD front bezel” on page 79 Note: The part marked a is fragile and might be damaged by rough handling. When you remove the camera, do not hold that part to avoid the damage.
2040 LCD panel, LCD cable, and hinges For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1060 PCI Express Mini Car d slot cover and PCI Express Mini Card for 802.1 1 a/b/g wireless LAN” on page 51 v “1070 PCI Express Mini Car d slot cover and PCI Express Mini Card 802.
5 4 3 When installing: Make sure that the camera connector is attached firmly . Remove the hinges from the LCD panel. 6 6 6 7 7 6 Step Screw (quantity) Color T orque 6 M2 × 3 mm, pan-head, nylon-coated (4) Silver 0.245 Nm (2.5 kgfcm) Remove the LCD cable assembly from the LCD panel.
2050 Wireless LAN antenna cables For access, remove these FRUs in or der: v “1010 Battery pack” on page 46 v “1060 PCI Express Mini Car d slot cover and PCI Express Mini Card for 802.1 1 a/b/g wireless LAN” on page 51 v “1070 PCI Express Mini Car d slot cover and PCI Express Mini Card 802.
For the antennas with three cables 2 2 3 4 2 1 1 2 Step Screw (quantity) Color T orque 2 M2 × 4 mm, pan-head, nylon-coated (4) Silver 0.245 Nm (2.
Locations Front view 1 Integrated camera (for some models) 2 Power switch 3 Lenovo Care button 4 Instant on button 5 V olume control buttons 6 Keyboard 7 Fing.
Rear view 1 USB connector 2 AC power connector 3 USB connector 4 RJ-45 (Ethernet) connector 5 RJ-1 1 (modem) connector 6 Optical drive 7 W ireless radio switc.
Parts list v Each FRU is available for all types or models, unless specific types or models are specified. v FRU with specific models listed and described as xxU (where U is an example of a country designator) should be used for all models ending in U.
Overall 1 3 2 4 5 6 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 b c 8 9 a 7 Parts list Lenovo 3000 V100 and V200 89.
No. FRU FRU no. RoHS ID CRU ID a - c See “Miscellaneous parts” on page 1 14. 1 LCD unit (see “LCD FRUs” on page 101.) 2 Hinge caps 41W6375 R N 3 Middle cover 41W6374 R N 4 Keyboard (see “Keyboar d” on page 103.
No. FRU FRU no. RoHS ID CRU ID 8 Bluetooth daughter card (BDC) v 0763-22x, 23x, 25x, 26x, 27x, 29x, 34x, 36x, 38x, 43x, 44x, 46x, 49x, 62x, 64x, 66x, 68x, 69x, 82x, 83x, 84x, 86x, 88x, 89x, 99x, A2x, .
No. FRU FRU no. RoHS ID CRU ID 10 System board assembly , 12W integrated v 0763- 2Lx, 2Mx, 2Ux, 2Vx, 2Wx 2Xx, 3Lx, 3Mx, 3Nx, 4Jx, 4Kx, 4Nx, 4Rx, 4Sx, 4Tx, 4Ux, 4Vx, 4Xx, 4Yx, 4Zx, 5Kx, 5Mx, 5Nx, 5Px, .
No. FRU FRU no. RoHS ID CRU ID 14 Intel PRO W ireless 3945ABG Mini-PCI Expr ess Adapter v 0763-22x, 23x, 25x, 26x, 27x, 29x, 36x, 38x, 43x, 44x, 46x, 49x, 62x, 64x, 66x, 68x, 69x, 82x, 83x, 84x, 86x, .
No. FRU FRU no. RoHS ID CRU ID 14 ThinkPad 1 1a/b/g/n W ireless LAN Mini-PCI Express Adapter v 0763-2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Sx, 4Cx, 4Hx, 5Dx, 5Fx, 6Cx, 6Ex, 6Fx, 6Hx, 7Dx, 7Fx, 7Gx, 2Vx, 3Nx, .
No. FRU FRU no. RoHS ID CRU ID 16 S ATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm, T oshiba v 0763-36x, 65x, 69x, 82x, 99x, A3x, B3x, C3x, C6x, C8x, E4x, E6x, J5x, 2Gx, 4Bx, 2Xx 27R2389 R ** S ATA hard disk drive, 60 GB, 9.
No. FRU FRU no. RoHS ID CRU ID 16 S ATA hard disk drive, 100 GB, 9.5 mm, 5,400 rpm v 0763-27x, 29x, 43x, 44x, 46x, 64x, 68x, A2x, A6x, A8x, G2x, J9x, 2Cx, 2Dx, 2Ex, 2Fx, 3Cx, 3Dx, 5Cx, 5Dx, 5Gx, 5Hx, 5Jx, 6Cx, 6Fx, 4Rx, 4Sx, 4Vx, 4Xx, 4Zx, 5Zx HGST 27R2385 R ** T oshiba 27R2393 R ** S ATA hard disk drive, 100 GB, 9.
No. FRU FRU no. RoHS ID CRU ID 19 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card OP v 0763-22x, 23x, 25x, 26x, 27x, 33x, 34x, 36x, 38x, 46x, 49x, 59x, 62x, 64x, 65x, 66x, 68x, 69x, 77x, 82x, 83x,.
No. FRU FRU no. RoHS ID CRU ID 22 Battery pack, Li-ion (6 cell), Sony v 0763-27x, 29x, 34x, 36x, 38x, 43x, 44x, 49x, 62x, 64x, 66x, 68x, 69x, 77x, 82x, 83x, 85x, 86x, 88x, 93x, A2x, A3x, A5x, A6x, A8x.
No. FRU FRU no. RoHS ID CRU ID 24 CPU assembly , Intel Cor e Solo processor T1300 (1.66 GHz) (667 MHz) v 0763-33x, 34x, 36x, 59x, 77x, 93x, 97x, 99x, B3x, B7x, D9x, F3x 41W1 140 R N CPU assembly , Intel Cor e Duo processor T2050 (1.6 GHz) (667 MHz) v 0763-J8x 41W1461 R N CPU assembly , Intel Cor e Duo processor T2250 (1.
No. FRU FRU no. RoHS ID CRU ID 24 CPU assembly , Intel Cor e 2 Duo processor T7100 (1.83 GHz) v 0764-22x, 23x, 26x, 28x, 29x, 2Bx, 2Lx, 2Mx, 42x, 43x, 44x, 45x, 46x, 4Cx, 4Dx, 4Ex, 4Fx, 4Jx, 4Lx, 4Mx, 4Px, 4Qx, 4Rx, 4Tx, 4Ux 42W7654 R N CPU assembly , Intel Cor e 2 Duo processor T7200 (2.
LCD FRUs 1 2 3 4 6 7 8 5 Parts list Lenovo 3000 V100 and V200 101.
12.1-in. WXGA TFT No. FRU FRU no. RoHS ID CRU ID 1 LCD front bezel 41W6369 R N 2 LCD panel, 12.1-in. WXGA AG, Samsung 13N7184 R N LCD panel, 12.1-in. WXGA AG, AUO 13N7182 R N LCD panel, 12.
Keyboard Keyboard for MT 0763 Language P/N (NMB) P/N (Chicony) RoHS ID CRU ID Arabic 39T7368 39T7432 R N Belgian 39T7365 39T7429 Chinese, T raditional 39T7379 39T7443 Czech 39T7373 39T7437 Danish 39T7362 39T7426 Dutch 39T7359 39T7423 English, U.K. 39T7357 39T7421 English, U.
Keyboard for MT 0764 Language P/N (NMB) P/N (Chicony) RoHS ID CRU ID Arabic 42T3353 42T3418 R N Belgian 42T3350 42T3415 Chinese, T raditional 42T3364 42T3429 Czech 42T3358 42T3423 Danish 42T3347 42T3412 Dutch 42T3344 42T3409 English, U.K. 42T3342 42T3407 English, U.
Recovery discs Windows XP Professional CDs W indows XP Professional is pr einstalled as the operating system in the following models: v 0763-22x, 23x, 27x, 29x, 43x, 44x, 46x, 49x, 84x, 88x, 89x, A3x,.
Windows XP Home Edition CDs W indows XP Home Edition is preinstalled as the operating system in the following models: v 0763-25x, 26x, 33x, 34x, 36x, 38x, 59x, 62x, 64x, 65x, 66x, 68x, 69x, 77x, 82x, .
Windows V ista Home Premium (32 bit) DVDs for MT 0763 W indows V ista Home Premium is pr einstalled as the operating system in the following models: v 0763-2Lx, 3Nx, 4Jx, 4Nx, 4Vx, 4Zx, 5Wx, 5Xx, 5Zz Language P/N RoHS ID CRU ID Chinese, T raditional 43T7173 R * Chinese, T raditional (Hong Kong S.
Windows V ista Home Premium (32 bit) DVDs for MT 0764 W indows V ista Home Premium is pr einstalled as the operating system in the following models: v 0764-24x, 2Ax, 2Bx, 43x, 46x, 49x, 4Dx, 4Rx Language P/N RoHS ID CRU ID Bulgarian 44Y0027 R * Chinese, Simplified 44Y0004 Chinese, T raditional 44Y001 1 Chinese, T raditional (Hong Kong S.
Windows V ista Home Basic (32 bit) DVDs for MT 0763 W indows V ista Home Basic is preinstalled as the operating system in the following models: v 0763-2Xx, 3Lx, 4Sx, 4Tx, 4Ux, 4Xx, 4Yx, 5Kx, 5Px, 5Sx, 5Tx Language P/N RoHS ID CRU ID Chinese, T raditional 43T7127 R * Chinese, T raditional (Hong Kong S.
Windows V ista Home Basic (32 bit) DVDs for MT 0764 W indows V ista Home Basic is preinstalled as the operating system in the following models: v 0764-22x, 44x, 48x, 4Cx, 4Fx, 4Hx, 4Jx, 4Lx, 4Px, 4Ux Language P/N RoHS ID CRU ID Chinese, Simplified 44Y0069 R * Chinese, T raditional 44Y0076 Chinese, T raditional (Hong Kong S.
Windows V ista Business (32 bit) DVDs for MT 0763 W indows V ista Business is preinstalled as the operating system in the following models: v 0763-2Mx, 2Ux, 2Vx, 2Wx, 3Mx, 4Kx, 4Rx, 5Mx, 5Nx, 5Qx, 5Rx, 5Ux, 5Yx, 6Jx, 6Kx Language P/N RoHS ID CRU ID Chinese, T raditional 43T7081 R * Chinese, T raditional (Hong Kong S.
Windows V ista Business (32 bit) DVDs for MT 0764 W indows V ista Business is preinstalled as the operating system in the following models: v 0764-23x 26x, 27x, 28x, 29x, 2Cx, 2Lx, 2Mx, 32x, 42x, 45x,.
Windows V ista Ultimate (32 bit) DVDs W indows V ista Ultimate is preinstalled as the operating system in the following models: v 0764-25x, 2Dx, 4Gx, 4Kx Language P/N RoHS ID CRU ID Chinese, Simplified 44Y0095 R * Chinese, T raditional 44Y0101 Chinese, T raditional (Hong Kong S.
Corel software CDs Language P/N RoHS ID CRU ID English, U.S. 41X0440 R * French 41X0443 Japanese 41X0608 Portuguese, Brazilian 41X0449 Spanish 41X0446 Miscellaneous parts FRU P/N RoHS ID CRU ID Screw kit, (including nylon-coated scr ews) for MT 0763: v M2 × 2 mm (silver), pan-head (4) v M2 × 2.
AC adapters FRU P/N RoHS ID CRU ID 2-pin (65 W, 20 V) adapter (models xxE, xxF , xxJ, xxL, xxP , xxS, xxU, xxY) OP Delta 92P1 155 R * Lite-On 92P1 159 R * Astec 92P1214 R * 3-pin (65W , 20 V) ad.
Power cords A Lenovo 3000 power cord for a specific country or r egion is usually available only in that country or region: For 2-pin power cords: Region P/N (Longwell) P/N (V olex) RoHS ID CRU ID Argentina 42T5020 42T5105 R * Brazil 42T5026 42T51 1 1 Canada, U.
Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area.
estimated through extrapolation. Actual r esults may vary . Users of this document should verify the applicable data for their specific environment. T rademarks The following terms are trademarks of L.
T rademarks Lenovo 3000 V100 and V200 11 9.
Part Number: 42X3554 (1P) P/N: 42X3554.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lenovo V200 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lenovo V200 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lenovo V200, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lenovo V200 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lenovo V200, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lenovo V200.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lenovo V200. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lenovo V200 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
