Manuel d'utilisation / d'entretien du produit SL300 du fabricant Lenovo
Aller à la page of 154
T hinkP a d SL3 00 Hard w ar e M a in t e n a n c e Ma nu a l.
.
T hinkP a d SL3 00 Hard w ar e M ain t e n an c e Ma nu a l.
Note Before using this information and the pr oduct it supports, be sure to read the general information under “Notices” on page 143. Forth Edition (March 2009) © Copyright Lenovo 2008, 2009.
Contents About this manual . . . . . . . . . .v Safety information . . . . . . . . . .1 General safety . . . . . . . . . . . . . .2 Electrical safety . . . . . . . . . . . . .3 Safety inspection guide . . . . . . . . . . .5 Handling devices that are sensitive to electr ostatic discharge .
Common service tools . . . . . . . . . 141 Notices . . . . . . . . . . . . . . 143 T rademarks . . . . . . . . . . . . . . 144 iv ThinkPad SL300 Hardwar e Maintenance Manual.
About this manual This manual contains service and refer ence information for the following ThinkPad ® products. ThinkPad SL300 MT 2738 Use this manual along with the advanced diagnostic tests to troubleshoot problems.
vi ThinkPad SL300 Hardwar e Maintenance Manual.
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad computer . v “General safety” on page 2 v “Electrical safety.
General safety Follow these rules to ensur e general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet.
Electrical safety Observe the following rules when working on electrical equipment. v Find the room emer gency power-of f (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly .
v Do not touch live electrical circuits with the r eflective surface of a plastic dental mirror . The surface is conductive; such touching can cause personal injury and machine damage.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, requir ed safety items were installed to pr otect users and service personnel from injury .
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electr ostatic discharge (ESD.) ESD damage can occur when there is a dif ference in charge between objects.
Safety notices: multilingual translations The safety notices in this section are pr ovided in English, French, German, Hebrew , Italian, Japanese, and Spanish. Safety notice 1 Before the computer is power ed on after FRU replacement, make sure all scr ews, springs, and other small parts are in place and ar e not left loose inside the computer .
Safety notice 2 D ANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery , recharge it, throw it into fire or water , or short-circuit it. Dispose of the battery as required by local ordinances or regulations.
Safety notice 3 D ANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water , or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Safety notice 4 D ANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector , disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water . Dispose of the battery as required by local ordinances or regulations.
Safety notice 5 If the LCD breaks and the fluid fr om inside the LCD gets into your eyes or on your hands, immediately wash the affected ar eas with water for at least 15 minutes. Seek medical care if any symptoms fr om the fluid are present after washing.
Safety notice 6 D ANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.
Safety notice 8 D ANGER Before removing any FRU, power off the computer , unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables.
Laser compliance statement Some models of ThinkPad computer are equipped fr om the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: D ANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
16 ThinkPad SL300 Hardwar e Maintenance Manual.
Important service information This chapter presents following important service information: v “Strategy for replacing FRUs” – “Strategy for replacing a har d disk drive” on page 18 – “I.
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue . v Some computers have both a processor boar d and a system board.
Strategy for replacing FRUs for CTO, CMV , and GA V Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configur e an IBM ® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, wher e it is built and shipped directly to the customer .
v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim r ecord under SYSTEM DET AILS. v Authorized IBM Business Partners can access Eclaim at the following We b site: https://wca.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry . RoHS requirements must be implemented on Lenovo products placed on the market after June 2006.
22 ThinkPad SL300 Hardwar e Maintenance Manual.
General checkout This chapter presents following information: v “What to do first” on page 24 v “Checkout guide” on page 25 – “Diagnostics using PC-Doctor for DOS” on page 26 – “PC-D.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4.
Checkout guide Use the following procedur es as a guide in identifying and correcting problems with the ThinkPad computer . Note: The diagnostic tests are intended to test only ThinkPad pr oducts. The use of non-ThinkPad products, pr ototype cards, or modified options can lead to false indications of errors and invalid system r esponses.
Diagnostics using PC-Doctor for DOS The ThinkPad computer has a test program called PC-Doctor for DOS (her eafter called PC-Doctor .) Yo u can detect errors by running the diagnostics test included in PC-Doctor . This section is an overview of the procedure.
Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu. The options on the test menu are as follows: Diagnostics Interactive .
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v System Configuration v Memory Contents v Physical Disk Drives v Logical Disk Drives v.
Power system checkout To verify a symptom, do the following: 1. T urn off the computer . 2. Remove the battery pack. 3. Connect the ac adapter . 4. Check that power is supplied when you turn on the computer . 5. T urn off the computer . 6. Disconnect the ac adapter and install the charged battery pack.
Checking operational charging To check whether the battery charges properly during operation, use a dischar ged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer . Perform operational charging.
Checking the backup battery Do the following: 1. Power off the computer , and unplug the ac adapter fr om it. 2. T urn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 63). 4. Remove the backup battery (see “1 160 Backup battery” on page 86).
32 ThinkPad SL300 Hardwar e Maintenance Manual.
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 34 v “Power management” on.
8. When the recovery pr ocess is complete, the W elcome to Microsoft W indows screen is displayed. Follow the instr uctions on the screen to complete the W indows setup. Passwords As many as three passwor ds may be needed for any ThinkPad computer: the power-on passwor d (POP), the hard-disk password (HDP), and the supervisor password (SVP).
How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. T urn off the computer . 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 63.
6. Select Change HDD Master Password by using the cursor directional keys. 7. T ype the current master HDP in the Enter CURRENT Password field. then leave the Enter New Password field blank, and press Enter twice. 8. Press F10. 9. Select OK in the Setup Configuration window .
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby , and hibernation. Screen blank mode If the time set on the “T urn off monitor” timer in the operating system expir es, the LCD backlight turns off.
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. W ait a few seconds before taking any action to r eenter operation mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 44 v “Beep symptoms” on page 45 v “No-beep symptoms” on page 45 v .
T able 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 7001 (HDCP) Memory is not enough for HDCP Key Provisioning! Add the DIMMs. 7002 (HDCP) Failed to check the key set Family-EKS! System board. 7003 (HDCP) Chip-Unique-EKS re-encryption failed! System board.
T able 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 8318 S.M.A.R.T . Capable but Command Failed 1. Hard disk drive. 2. System board. 3. S ATA cable. 8319 S.M.A.R.T . Command Failed 1. Hard disk drive. 2. System board.
T able 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 850D PCI IRQ routing table err or Update the BIOS. 850E T imer Error System board. 850F Refresh timer test failed System board. 8510 Interrupt Controller -1 error System board.
T able 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 870A Unknown BIOS error . Error code = 004Bh Update the BIOS. 870B Floppy Controller Failur e 1. External floppy disk drive. 2. System board. 8800 W arning! Unsupported USB device found and disabled! Remove unsupported USB devices.
Error messages T able 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility . 2. Backup battery . 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility .
Beep symptoms T able 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. Reseat the LCD connector . 2. LCD assembly . 3. External CRT . 4. System board. One long and two short beeps, and a blank or unreadable LCD.
LCD-related symptoms T able 5. Minimum quantity of defective pixels required for LCD replacement on June 2006 or later manufactured ThinkPad LCD resolution Bright dots Dark dots Bright and dark dots X.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardwar e defect, such as cosmic radiation, electrostatic discharge, or softwar e errors. FRU replacement should be consider ed only when a problem r ecurs.
48 ThinkPad SL300 Hardwar e Maintenance Manual.
ThinkPad SL300 This chapter presents following pr oduct-specific service references and product-specific parts information. v “Specifications” v “Status indicators” on page 52 v “FRU tests.
T able 7. Specifications (continued) Feature Description Standard memory v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 2 v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1 v 1-GB DDR2-667 SDRAM S.
T able 7. Specifications (continued) Feature Description Battery v Li-ion battery (4 cells) 2.6 Ah v Li-ion battery (6 cells) 2.4 Ah v Li-ion battery (9 cells) 2.
Status indicators The system status indicators show the status of the computer , as follows: 1 2 3 4 5 6 7 8 9 10 T able 8. Status indicators Indicator Meaning 1 Power on The computer is on and ready to use. The power switch stays lit whenever the computer is on and is not lit when the computer is in sleep (standby) mode.
T able 8. Status indicators (continued) Indicator Meaning 6 Sleep (standby in W indows XP) status Green: The computer is in sleep (standby) mode. Blinking green: The computer is entering sleep (standby) mode or hibernation mode, or is resuming normal operation.
FRU tests The following table shows the test for each FRU. T able 9. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard Power Diagnostics --> ThinkPad Devices --> AC Adapter , Battery 1 (Battery2) LCD unit 1.
T able 9. FRU tests (continued) FRU Applicable test T rackPoint or pointing device If the T rackPoint does not work, check the configuration as specified in the BIOS Setup Utility . If the T rackPoint is disabled, select Automatic to enable it. After you use the T rackPoint, the pointer may drift on the screen for a short time.
Fn key combinations The following table shows the function of each combination of Fn with a function key . T able 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock your computer . Fn+F3 Select a power scheme that has been created by Power Manager .
T able 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme dir ectly , with no need to start Presentation Dir ector . To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Dir ector , and change the settings.
FRU replacement notices This section contains notices related to r emoving and replacing parts. Read this section carefully befor e replacing any FRU. Screw notices Loose screws can cause a r eliability problem.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number . When you replace the system boar d, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad SL Series Maintenance Diskette V ersion 1.
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stor ed in the EEPROM of the system board. The electr onic storage of this information simplifies the procedur e to check if the ECA has been previously applied to a machine.
Removing and replacing a FRU This section presents dir ections and drawings for use in removing and replacing a FRU. Be sure to observe the following general r ules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.
1010 Battery pack D ANGER T able 11 . Removal steps of battery pack Unlock the battery release lever 1 . Holding the battery r elease lever in the unlocked position 2 , remove the battery pack in the dir ection shown by arrow 3 . 3 1 2 When installing: Install the battery pack along the slide rails of the slot.
1020 Optical drive For access, remove this FRU: v “1010 Battery pack” on page 63 T able 12. Removal steps of optical drive 1 Step Screw (quantity) Color T orque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.
1030 Hard disk drive (HDD) cover and HDD For access, remove this FRU: v “1010 Battery pack” on page 63 T able 13. Removal steps of HDD cover and HDD 1 Step Screw (quantity) Color T orque 1 M2 × 8 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.
T able 13. Removal steps of HDD cover and HDD (continued) 3 When installing: Make sure that the HDD connector is attached firmly . 66 ThinkPad SL300 Hardwar e Maintenance Manual.
1040 DIMM slot cover For access, remove this FRU: v “1010 Battery pack” on page 63 T able 14. Removal steps of DIMM slot cover Note: Loosen the screws 1 , but do not r emove them.
1050 DIMM For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1040 DIMM slot cover” on page 67 T able 15. Removal steps of DIMM 2 1 1 Note: If only one DIMM is used on the computer you are servicing, the car d must be installed in SLOT -0 ( a : lower slot), but not in SLOT -1 ( b : upper slot).
1060 PCI Express Mini Card for wireless WA N For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1040 DIMM slot cover” on page 67 T able 16.
T able 16. Removal steps of PCI Express Mini Card (full size) for wireless WAN (continued) 3 When installing: Plug the black cable with red label into the jack labeled MAIN , and the black cable with blue label into the jack labeled AUX on the card.
1070 Intel T urbo Memory Minicard For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1040 DIMM slot cover” on page 67 T able 17. Removal steps of Intel T urbo Memory Minicard 1 1 Step Screw (quantity) Color T orque 1 For Japan M2 × 3 mm, tamper proof (2) Black 0.
1080 Thermal door For access, remove this FRU: v “1010 Battery pack” on page 63 T able 18. Removal steps of thermal door Note: Loosen the screws 2 , but do not r emove them.
1090 Fan assembly For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1080 Thermal door” on page 72 T able 19. Removal steps of fan assembly 1 2 3 3 2 4 4 Step Screw (quantity) Color T orque 2 M2 × 4 mm, wafter-head, nylon-coated (2) Silver 0.
T able 19. Removal steps of fan assembly (continued) 5 6 T able 20. Installation of the fan assembly When installing: v Before you attach the fan assembly to the computer , apply thermal gr ease, at an amount of 0.2 grams, on the part marked a as in the following figure.
1 100 CPU thermal module For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1080 Thermal door” on page 72 v “1090 Fan assembly” on page 73 T able 21. Removal steps of CPU thermal module 1 2 3 4 Step Screw (quantity) Color T orque 1 to 4 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.
T able 21. Removal steps of CPU thermal module (continued) 6 5 T able 22. Installation of the CPU thermal module When installing: v Before you attach the CPU thermal module to the computer , apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure.
111 0 CPU For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1080 Thermal door” on page 72 v “1090 Fan assembly” on page 73 v “1 100 CPU thermal module” on page 75 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling.
1 120 Palm rest For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 T able 24. Removal steps of palm rest 1 1 1 2 1 Step Icon Screw (quantity) Color T orque 1 M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.
T able 24. Removal steps of palm rest (continued) 4 3 3 3 3 4 Step Icon Screw (quantity) Color T orque 3 M2 × 9 mm, wafer-head, nylon-coated (4) Black 0.
T able 24. Removal steps of palm rest (continued) 7 80 ThinkPad SL300 Hardwar e Maintenance Manual.
1 130 Bluetooth daughter card (BDC) For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1 120 Palm r est” on page 78 T able 25. Removal steps of BDC 1 2 Step Screw (quantity) Color T orque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.
1 140 PCI Express Mini Card for wireless LAN/WiMAX For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1 120 Palm r est” on page 78 T able 26.
T able 26. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX (continued) 3 ThinkPad SL300 83.
1 150 Keyboard For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1 120 Palm r est” on page 78 T able 27. Removal steps of keyboard 1 Step Icon Screw (quantity) Color T orque 1 M2 × 16 mm, wafer-head, nylon-coated (1) Black 0.
T able 27. Removal steps of keyboard (continued) 5 7 6 6 6 6 7 When installing: Make sure that the connectors ar e attached firmly . ThinkPad SL300 85.
1 160 Backup battery D ANGER For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1 120 Palm r est” on page 78 T able 28. Removal steps of backup battery 1 2 When installing: Make sure that the battery connector is attached firmly .
1 170 To p case sub assembly For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1 120 Palm r est” on page 78 v “1 150 Keyboar d” on page 84 T able 29.
T able 29. Removal steps of top case sub assembly (continued) 6 7 9 8 8 9 8 8 9 9 Step Screw (quantity) Color T orque 6 M2 × 2 mm, wafer-head, nylon-coated (1) Silver 0.167 Nm (1.7 kgfcm) 7 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.
1 180 Magnesium frame assembly For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1 120 Palm r est” on page 78 v “1 150 Keyboar d” on page 84 v “1 170 To p case sub assembly” on page 87 T able 30.
1 190 I/O board For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1 1.
T able 31. Removal steps of I/O board (continued) 5 5 5 5 6 7 Step Screw (quantity) Color T orque 5 M2 × 4 mm, wafer-head, nylon-coated (4) Silver 0.
1200 LCD unit For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot cover” on page 67 v “106.
T able 32. Removal steps of LCD unit (continued) 3 Step Screw (quantity) Color T orque 3 M2 × 5 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.
T able 32. Removal steps of LCD unit (continued) In step 4 , remove the tapes securing the antenna cables, and r elease the cables from the cable guides of the base cover 5 .
T able 32. Removal steps of LCD unit (continued) 7 7 When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sur e that they are not subjected to any tension. T ension could cause the cables to be damaged by the cable guides, or a wire to be br oken.
1210 System board Important notices for handling the system board: When handling the system board, bear the following in mind. v The system boar d has an accelerometer , which can be broken by applying several thousands of G-forces.
For access, remove these FRUs, in or der: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Har d disk drive (HDD) cover and HDD” on page 65 v “1040 DIMM slot co.
Following components soldered on the top side of the system boar d are extremely sensitive. When you service the system board, avoid any kind of r ough handling.
T able 33. Removal steps of system board 1 2 2 Step Screw (quantity) Color T orque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 2 Hex stud, spring washer (2) Silver 0.
T able 33. Removal steps of system board (continued) 3 3 3 5 3 4 Step Screw (quantity) Color T orque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.167 Nm (1.7 kgfcm) 5 M2 × 9mm, wafer-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 6 When installing: Make sure that the connector is attached firmly .
1220 Small board For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “10.
1230 Base cover For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “104.
2010 LCD front bezel For access, remove this FRU: v “1010 Battery pack” on page 63 T able 36. Removal steps of LCD front bezel 1 1 1 1 Step Screw cap Screw (quantity) Color T orque 1 M2 × 4 mm, bind-head, nylon-coated (4) Silver 0.167 Nm (1.
2020 Integrated camera For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “2010 LCD front bezel” on page 103 Note: Some models do not have the integrated camera. T able 37. Removal steps of integrated camera 3 2 1 When installing: Make sure that the connector is attached firmly .
2030 LCD panel For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk drive (HDD) cover and HDD” on page 65 v “1040.
T able 38. Removal steps of LCD panel (continued) 2 3 4 When installing: Make sure that the LCD cable is attached firmly . 106 ThinkPad SL300 Hardwar e Maintenance Manual.
2040 Antenna assembly , LCD cable, camera cable, and hinges For access, remove these FRUs in or der: v “1010 Battery pack” on page 63 v “1020 Optical drive” on page 64 v “1030 Hard disk driv.
T able 39. Removal steps of antenna assemblies and camera cable (continued) 2 2 2 108 ThinkPad SL300 Hardwar e Maintenance Manual.
T able 39. Removal steps of antenna assemblies and camera cable (continued) 3 3 3 3 4 5 5 4 a b a b Step Screw (quantity) Color T orque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.167 Nm (1.7 kgfcm) 4 M2 × 3 mm, shoulder , wafer-head, nylon-coated (4) Black 0.
T able 39. Removal steps of antenna assemblies and camera cable (continued) 6 6 11 0 ThinkPad SL300 Hardware Maintenance Manual.
T able 40. Installation of the antenna assemblies and the camera cable When you install the antenna assembly and the camera cable, place them as shown in this figure.
Locations Front view 1 Built-in microphone 2 Integrated camera 3 Built-in stereo speakers 4 Power switch 5 System status indicators Note: For the description of each indicator , see “Status indicators” on page 52.
1 1 2 3 3 4 5 13 14 15 16 17 18 19 20 21 6 7 8 9 10 11 12 ThinkPad SL300 11 3.
Rear view 1 IEEE 1394 connector 2 7–in1 Media Card Reader 3 USB (Universal serial bus) connectors 4 HDMI port 5 External monitor connector 6 RJ-1 1 (modem) connec.
Parts list This section contains following lists of the service parts. v “Overall” on page 11 6 v “LCD FRUs” on page 129 v “Keyboard” on page 132 v “Miscellaneous parts” on page 133 v .
Overall 1 2 3 4 5 a 6 b c 7 8 9 26 25 23 24 5 21 22 d 20 19 18 17 16 15 14 13 12 10 11 11 6 ThinkPad SL300 Hardware Maintenance Manual.
T able 41. Parts list—Overall No. FRU FRU no. RoHS ID CRU ID a - d See “Miscellaneous parts” on page 133. 1 LCD unit (see “LCD FRUs” on page 129.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 4 CPU assembly , Intel Celeron Dual Core processor T1700 (1.83 GHz) v 2738-CTO, 92x, 96x, 9Bx, 9Ux 42W8147 R N 4 CPU assembly , Intel Core 2 Duo mobile processor P7370 (2.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 4 CPU assembly , Intel Core 2 Duo mobile processor T5870 (2.0 GHz) v 2738-CTO, 27x, 2Ax, 2Cx, 2Px, 2Qx, 2Tx, 2Ux, 2Zx, 4Nx, 5.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 7 Battery pack, Li-ion (6 cell, 2.4 Ah) v 2738-CTO, 22x, 23x, 26x, 27x, 28x, 29x, 2Bx, 2Dx, 2Kx, 2Lx, 2Mx, 2Nx, 2Zx, 33x, 34x.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 7 Battery pack, Li-ion (6 cell, 2.4 Ah) v 2738-CTO, 22x, 23x, 26x, 27x, 28x, 29x, 2Bx, 2Dx, 2Kx, 2Lx, 2Mx, 2Nx, 2Zx, 33x, 34x.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 9 DVD multi drive, 12.7 mm v 2738-CTO, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Qx, 2.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 9 Blu-ray combo drive, 12.7 mm v 2738-CTO, 2Px, 2Tx, 3Dx, 3Ex, 5Bx, 6Lx, 6Nx, 6Qx, 6Sx, 7Px, 7Tx, 8Hx, 9Cx, 9Ex, H3x, HGx, HHx 42T2579 R * 9 Blu-ray drive, 12.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 12 S ATA hard disk drive, 250 GB, 9.5 mm, 5,400 rpm v 2738-CTO, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Cx, 2Jx, 2Qx, 2Rx, 2Ux, 2Vx, 2.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 16 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card v 2738-CTO, 6Zx 40Y8402 R * 16 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card v.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 18 Thermal module with discrete fan v 2738-CTO, 22x, 23x, 2Cx, 2Dx, 2Tx, 2Ux, 2Vx, 2Wx, 2Xx, 33x, 34x, 37x, 3Bx, 3Hx, 3Mx, 3Q.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 22 Bluetooth daughter card (BDC-2.1) v 2738-CTO, 22x, 23x, 24x, 25x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Kx, 2Lx, 2Mx, 2.
T able 41. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 24 Palm rest assembly with fingerprint r eader 13W v 2738-CTO, 22x, 23x, 24x, 25x, 26x, 2Ax, 2Bx, 2Cx, 2Dx, 2Jx, 2Kx, 2Lx, 2M.
LCD FRUs In ThinkPad SL300, there is a following type of LCD. v “13.3-in. WXGA TFT” 13.3-in. WXGA TFT 1 4 3 5 6 7 8 6 2 ThinkPad SL300 129.
T able 42. Parts list—13.3-in. WXGA TFT No. FRU FRU no. RoHS ID CRU ID 1 LCD bezel SL300 45N3190 R N 2 Camera/microphone module v 2738-CTO, 22x, 23x, 24x, 26x, 27x, 28x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Jx.
T able 42. Parts list—13.3-in. WXGA TFT (continued) No. FRU FRU no. RoHS ID CRU ID 3 W ireless LAN/W iMAX antenna assembly v 2738-CTO, H2x 43Y9834 R N 4 W ireless WA N antenna assembly v 2738-CTO, 2.
Keyboard T able 43. Parts list—Keyboard Language P/N RoHS ID CRU ID Arabic 42T3884 42T3818 R N Belgian 42T3881 42T3815 Brazilian Portuguese 42T3900 42T3834 Bulgarian 42T4144 42T4140 Canadian French .
Miscellaneous parts T able 44. Parts list—Miscellaneous parts FRU P/N RoHS ID CRU ID Screw kit (including nylon-coated scr ews): v M1.6 × 4 mm v M2 × 2 mm v M2 × 3 mm v M2 × 4 mm v M2 × 5 mm v M2 × 6 mm v M2 × 7 mm v M2 × 8 mm v M2 × 9 mm v M2 × 12 mm v M2 × 15 mm v M2 × 16 mm v M2.
AC adapters T able 45. Parts list—2-pin AC adapters FRU P/N RoHS ID CRU ID 2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF , xxJ, xxL, xxP , xxS, xxY , xxU) 42T5282 R * 2-pin (65 W, 20 V) adapter (.
Power cords A ThinkPad power cord for a specific country or r egion is usually available only in that country or region: T able 47. Parts list—2-pin power cords Region P/N RoHS ID CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 R * Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.
Recovery discs Windows XP Professional DVDs W indows XP Professional is pr einstalled as the operating system in the following models: v 2738-CTO, 2Mx, 2Nx, 2Zx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x.
Windows V ista Home Basic (32 bit) DVDs W indows V ista Home Basic (32 bit) is pr einstalled as the operating system in the following models: v 2738-CTO, 27x, 28x, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 2Vx, 2.
Windows V ista Home Premium (32 bit) DVDs W indows V ista Home Pr emium (32 bit) is pr einstalled as the operating system in the following models: v 2738-CTO, 3Fx, 3Hx, 3Kx, 3Mx, 4Bx, 4Ex, 5Jx, 5Lx, 64x, 66x, 69x, 6Jx, 84x, 9Px, 9Qx, 9Rx, 9Sx, 9Tx, 9Ux, 9Wx, 9Xx, 9Yx, A4x T able 51.
Windows V ista Business (32 bit) DVDs W indows V ista Business (32 bit) is pr einstalled as the operating system in the following models: v 2738-CTO, 23x, 24x, 25x, 26x, 29x, 2Ax, 2Bx, 2Cx, 2Dx, 2Jx, .
Windows V ista Ultimate (32 bit) DVDs W indows V ista Ultimate (32 bit) is pr einstalled as the operating system in the following models: v 2738-CTO, 22x T able 53.
Common service tools T able 54. Parts list—Common service tools T ool P/N Screwdriver kit 95F3598 1/4 ″ drive spinner handle 1650840 1/4 ″ Sq. to 1/4 ″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
142 ThinkPad SL300 Hardwar e Maintenance Manual.
Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area.
vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation.
.
Part Number: 43Y6763_03 (1P) P/N: 43Y6763_03.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lenovo SL300 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lenovo SL300 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lenovo SL300, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lenovo SL300 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lenovo SL300, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lenovo SL300.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lenovo SL300. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lenovo SL300 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
