Manuel d'utilisation / d'entretien du produit 6531 du fabricant Lenovo
Aller à la page of 240
Har dwar e Maint enance Manual Machine T ypes: 6531, 6532, 6533, and 6534..
.
Har dwar e Maint enance Manual Machine T ypes: 6531, 6532, 6533, and 6534..
Note: Before using this information and the pr oduct it supports, read the gener al information in Appendix A “Notices” on page 221 and the W arranty and Support Information document on the ThinkServer Documentation DVD . Third Edition (September 2010) © Copyright Lenovo 2009, 2010.
Contents Chapter 1. About this manual . . . . . 1 Important Safety Information . . . . . . . . . . 1 Safety stat ements . . . . . . . . . . . . . . 2 Important information about replacing RoHS compliant FRUs . . . . . . . . . . . . . . . 5 T urkish stat ement of compliance .
Replacing a memory module (DIMM) . . . . . . 122 Supported memory types . . . . . . . . 122 Removing a memory module . . . . . . . 125 Installing a memory module . . . . . . . . 125 Replacing har d disk drives . . . . . . . . . . 126 Removing a simple-swap Serial A T A (SA T A) hard disk drive .
Before you use the EasyStartup DVD . . . . 208 EasyStartup overview . . . . . . . . . . 208 Installing your operating system without using EasyStartup . . . . . . . . . . . . . . 210 Updating the rmware . . . . . . . . . . . . 211 Using the EasyUpdate Firmware Updater tool .
viii Hardware Maintenance Manual.
Chapter 1. About this manual This Hardware Maint enance Manual contains information to help you solve pr oblems that might occur in your server . It describes the diagnostic tools that come with the server , error codes and suggest ed actions, and instructions for replacing failing components.
Safety statements Important: Each caution and danger stat ement in this document is labeled with a number . This number is used to cross refer ence an English-language caution or danger statement with translat ed versions of the caution or danger stat ement in the Safety Information document.
• Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as requir ed by local or dinances or regulations. Statement 3 CA UTION: When laser products (such as CD-ROMs, DVD drives, ber optic devices, or transmitt ers) are installed, note the following: • Do not remove the covers.
Statement 5 CA UTION: The power contr ol button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. T o remove all electrical current from the device, ensure that all power cords are disconnected from the power sour ce.
Important information about r eplacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a Eur opean Union legal requirement affecting the global electronics industry .
6 Hardware Maintenance Manual.
Chapter 2. Gener al information This chapter provides gener al information that applies to all machine types supported by this publication. F eatur es and technologies The server uses the following fe.
• Large system-memory capability The memory bus supports up t o 24 GB of memory when regist ered DIMMs ar e installed. The server supports up to 8 GB if unbuffered DIMMs are installed.
– Event logs for RAID controllers and service pr ocessors The diagnostics progr ams cr eate a merged log that includes events fr om all collect ed logs. The information is collect ed int o a le that you can send to the Lenovo technical support team to help diagnose a pr oblem.
T able 1. F eatures and specications Microprocessor: • Supports one Intel® quad-core (Xeon 3400 series) or dual-cor e (Celeron G1101, P entium G6950, or cor e i3 series) processor with the Ibe x.
T able 1. Features and specications (continued) RAID controllers: • An IBM ServeRAID-BR10il SAS/SA T A Controller that provides RAID levels 0, 1, and 1E (comes standard on some hot-swap SAS and hot-swap SA T A models).
EasyStartup The ThinkServer EasyS tartup pr ogram simplies the process of conguring your RAID contr ollers and installing support ed ® Microsoft ® Windows and Linux oper ating syst ems and device drivers on your server . The EasyStartup pr ogram is pr ovided with your server on DVD .
Chapter 3. General Check out Y ou can solve many pr oblems without outside assistance by following the tr oubleshooting pr ocedures in this Hardware Maint enance Manual and on the Lenovo W eb site. This document describes the diagnostic tests that you can perform, troubleshooting procedur es, and e xplanations of error messages and err or codes.
• F or intermittent problems, check the err or log; see “Event logs” on page 17 and “Diagnostic progr ams and messages” on page 64. P erforming the checkout procedure T o perform the checkout pr ocedure, complete the following steps: Step 1.
b. Collect system data. Run the Dynamic System Analysis (DSA) diagnostics pr ogram t o collect information about the hardwar e, rmwar e, softwar e, and oper ating syst em. Have this information available when you contact Lenovo or an approved warr anty service provider .
c) In the Browse by pr oduct window F amily: list, select ThinkServer RS210 . d) Click Downloads and drivers . e) Click User's guides and manuals t o look for related documentation. c. Check for service bulletins. L enovo service bulletins document known pr oblems and suggested solutions.
Chapter 4. Diagnostics This chapter describes the diagnostic t ools that ar e available to help you solve problems that might occur in the server . Diagnostic t ools The following tools ar e available.
• POS T event log: This log contains the thr ee most recent err or codes and messages that were gener ated during POS T . Y ou can view the POST event log thr ough the Setup utility . • System-event log: This log contains messages that wer e gener ated during POS T and all system status messages from the service processor .
T able 2. Methods for viewing event logs (continued) Condition Action The server is hung. • If DSA Preboot is installed, restart the server and press F2 t o start DSA Preboot and view the event logs. • If DSA P reboot is not installed, insert the DSA Pr eboot CD and r estart the server to start DSA Pr eboot and view the event logs.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
Information Information messages do not r equire action; they recor d signicant syst em-level events, such as when the server is started. Warning Warning messages do not requir e immediate action; they indicat e possible problems, such as when the recommended maximum ambient t emperatur e is ex ceeded.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
DVD drive pr oblems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 653.
General problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, .
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
Intermittent problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6.
K eyboard, mouse, or pointing-device pr oblems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
Memory problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6.
Microprocessor problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531,.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
Optional-device problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531.
P ower pr oblems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, .
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
Universal Serial Bus (USB) port pr oblems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
3. Remove the server cover and look inside the server for lit LEDs. Certain components inside the server have LEDs that will be lit to indicat e the location of a problem. F or e xample, a DIMM err or will light the LED next t o the failing DIMM on the system boar d.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapt er 7 “Parts listing, RS210 T ypes 6531, 6532, 6533, and 6534” on page 175 to determine which components ar e customer replaceable units (CRU) and which components are eld replaceable units (FRU).
System pulse LEDs The following LEDs are on the system board and indicates the syst em power -on and power -off sequencing and boot progr ess (see “System-boar d LEDs” on page 112 for the location of these LEDs). T able 4. System pulse LEDs LED Description Action Enclosure manager heartbeat power -on and power-off sequencing.
Note: Changes are made periodically to the L enovo W eb site. The actual pr ocedure might vary slightly from what is described in this document. Go t o http://www.
Viewing the test log T o view the t est log when the tests are complet ed, type the view command in the DSA inter active menu, or select Diagnostic Event Log in the gr aphical user int erface. T o transfer DSA P reboot collections t o an ext ernal USB device, type the copy command in the DSA inter active menu.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
T able 5. DSA P reboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
• In-band method: Recover server rmwar e, using either the boot block jumper (Automated Boot Recovery) and a server Firmwar e Update P ackage Service P ack. • Out-of-band method: Use the IMM W eb Int erface t o update the rmwar e, using the latest server rmware update package.
Step 7. Boot the server t o an oper ating system that is supported by the rmware updat e package that you downloaded. Step 8. P erform the rmwar e updat e by following the instructions that are in the rmware update package readme le. Step 9.
Solving power problems P ower problems can be difcult to solve. F or example, a short cir cuit can e xist anywher e on any of the power distribution buses. Usually, a short circuit will cause the power subsystem to shut down because of an over current condition.
Solving undetermined problems If the diagnostic tests did not diagnose the failur e or if the server is inoper ative, use the information in this section. If you suspect that a software problem is causing failures (continuous or intermittent), see “Software problems” on page 60.
00 00 00 00000000 00000000 00000000 00000000 • Machine type and model • Micr oprocessor or hard disk drive upgrades • F ailur e symptom – Does the server fail the diagnostic tests? – What oc.
106 Har dware Maint enance Manual.
Chapter 5. L ocating Server Contr ols and connect ors This section describes the contr ols, light-emitting diodes (LEDs), and connect ors on the front and rear of the server , and how to turn the server on and off. F or the location of the LEDs on the system board, see “System-boar d LEDs” on page 112 .
Rear view 1 P ower-cor d connector 9 NMI butt on 2 Serial connector 10 USB 3-4 connector 3 Ethernet 1 activity LED 11 USB 1-2 connector 4 Ethernet 1 link LED 12 Video connector 5 Ethernet 2 activity L.
3 DIMM 3 13 Oper ator information panel connector 23 Battery 4 DIMM 4 14 Simple-swap HDD backplane signal connector 24 P ower 2 connect or 5 DIMM 5 15 W ake-on-LAN connector 25 Virtual media key conne.
Microprocessor Heatsink Orientation DIMMs DIMMs 1 DIMM 1 8 DVD drive connector 2 DIMM 2 9 Hypervisor ash device connect or 3 DIMM 3 10 Riser-car d connect or 2 4 DIMM 4 11 Riser-car d connect or 1 .
1 PCI-X power cable 2 PCI-X slot System-board switches and jumpers The following illustration shows the switches and jumpers on the system board. Microprocessor Heatsink Orientation DIMMs DIMMs The following table describes the jumpers on the system board.
T able 6. S ystem board jumpers (continued) Jumper number Jumper name Jumper setting Notes: 1. If no jumper is pr esent, the server r esponds as if the pins ar e set to 1 and 2. 2. Changing the position of the UEFI boot r ecovery jumper from pins 1 and 2 t o pins 2 and 3 befor e the server is turned on alters which ash ROM page is loaded.
7 SAS/SA T A Controller LED 15 DIMM 1-6 error LEDs 8 IMM heart beat LED T able 7. System-board LEDs LED Description Error LEDs When one of these LEDs is lit, it indicates that the associated component has failed. Baseboard management controller heartbeat LED This LED ashes to indicat e that the IMM is functioning normally.
CA UTION: The power contr ol button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. T o remove all electrical current from the device, ensure that all power cords are disconnected from the power sour ce.
Chapter 6. Replacing FRUs This chapter provides detailed instructions for replacing FRUs in the server . Guidelines for trained service technicians This section contains information for trained service t echnicians.
• Check the ar ea for electrical hazar ds such as moist oors, nongr ounded power extension cords, power surges, and missing safety grounds. • Use only approved tools and test equipment. Some hand tools have handles that ar e cover ed with a soft material that does not pr ovide insulation fr om live electrical curr ents.
• Remove jewelry, such as br acelets, necklaces, rings, and loose-tting wrist watches. • Remove it ems from your shirt pocket, such as pens and pencils, that could fall into the server as you lean over it. • A void dropping any metallic objects, such as paper clips, hairpins, and scr ews, into the server .
000 000 000 000000 000000 000000 1 Riser card assembly 12 Bez el 2 DIMM air bafe 13 DVD drive ller 3 DIMM 14 Oper ator information panel 4 P ower supply 15 F ans 5 SAS/SA T A backplane (some models) 16 System board 6 SA T A simple-swap back panel (some models) 17 Micr oprocessor 7 3.
10 Hot-swap hard disk drive ller 11 3.5-inch or 2.5-inch hot-swap hard disk drive (depending on model) Removing and installing the cover Use the following pr ocedures to remove and install the cover: Removing the cover T o remove the server cover , do the following: 1.
00000000 00000000 00000000 00000000 00000000 Removing and installing the be zel T o remove the be zel, complete the following steps: 1. Remove the server fr om the rack and remove the cover (see “Removing and installing the cover ” on page 119). 2.
Attention: F or pr oper cooling and airow , r eplace the bez el and server cover befor e you turn on the server . T o install the bezel, insert the tab at the right end of the bez el into the fr ont of the chassis and pivot the bezel until it snaps into place.
Replacing a memory module (DIMM) T o replace a dual inline memory module (DIMM), use the following information and pr ocedures: Supported memory types F ollowing is information that describes the type.
Note: T o determine the type of a DIMM, see the label on the DIMM. The information on the label is in the format xxxxx nRxxx PC3-xxxxx-xx-xx-xxx. The numeral in the sixth numerical position indicates whether the DIMM is single-rank (n=1) or dual-r ank (n=2).
• The memory channels run at the fastest common fr equency of the installed DIMMs. • RDIMMs ar e supported in models with an Xeon 3400 series processor . • Do not use both RDIMMs and UDIMMs in the same server . • The server supports up t o thr ee single-r ank, dual-r ank, or quad-r ank RDIMMs per channel.
Note: The amount of usable memory is r educed, depending on the system congur ation. A certain amount of memory must be reserved for system resour ces. T o view the total amount of installed memory and the amount of congur ed memory, run the Setup utility .
T o install a DIMM, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for tr ained service t echnicians” on page 115. 2. T urn off the server and peripher al devices and disconnect the power cords and all ext ernal cables, if necessary .
Note: If a RAID controller or PCI card is installed, you might have t o recongur e the disk arr ays after you install or remove har d disk drives. See the documentation that comes with the PCI card for more information. Removing a simple-swap Serial A T A (SA T A) har d disk drive Attention: Simple-swap hard disk drives are not hot-swappable.
000000000 000000000 000000000 000000000 000000000 000000000 00000 00000 00000 000 000 000 6. Release the loops of the drive tray . 7. Insert the ller panel int o the bay to cover the drive.
000000000 000000000 000000000 000000000 000000000 000000000 3. Grasp the handle and pull the hot-swap drive assembly 2 out of the drive bay . Installing a hot-swap har d disk drive T o install a hot-swap hard disk drive, complete the following steps.
000000000 000000000 000000000 000000000 000000000 000000000 c. Gently push the drive assembly int o the bay until the drive stops. d. Push the tray handle 2 t o the closed (locked) position. e. Check the har d disk drive status LED to make sur e that the har d disk drive is operating correctly .
1 PCI-X power cable 2 PCI-X slot 7. Grasp the riser -card assembly at the front grip point and rear edges and lift to remove it fr om the server . 8. Place the riser -card assembly on a at, static-prot ective surface. 9. Carefully gr asp the PCI car d by its t op edge or upper corners, and pull the PCI card from the riser-car d assembly .
Installing a PCI card T o install a PCI card, complete the following st eps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for tr ained service t echnicians” on page 115.
Attention: PCI expansion-slot covers must be installed on all vacant slots. This maintains the electr onic emissions char acteristics of the server and ensur es pr oper cooling of server components. 6. F ollow the instructions that come with the PCI car d to set any jumpers or switches.
Removing a USB embedded hypervisor ash device T o r emove a hypervisor ash device, complet e the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for tr ained service t echnicians” on page 115.
6. Lift the oper ator information panel assembly out of the server . 7. If you ar e instruct ed to r eturn the oper ator information panel assembly, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
Replacing the drive cage T o r eplace the drive cage, use the following pr ocedures: Removing the drive cage The following illustration shows r emoving a simple-swap 3.5-inch drive cage. 0000 0000 0000 0000 0000 0000 The following illustr ation shows removing a hot-swap 3.
T o r emove a drive cage, complete the following st eps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for tr ained service t echnicians” on page 115. 2. T urn off the server and peripheral devices, and disconnect the power cor d and all external cables.
0000 0000 0000 0000 0000 0000 The following illustr ation shows installing a hot-swap 3.5-inch drive cage. The following illustr ation shows installing a hot-swap 2.
T o install a drive cage, complete the following steps: 1. Make sur e that the backplane or back plate is removed from the drive cage. (See “Removing the backplane or back plate (3.5-inch drives)” on page 153 or “Removing the SAS backplane (2.5-inch drives)” on page 155 for instructions, as applicable.
4. Remove the DIMM air bafe (see “Removing and installing the DIMM air bafe” on page 121). 5. Remove the heat sink. CA UTION: The heat sink may become very hot during normal oper ation. Allow time for the heat sink to cool down befor e you touch it.
10. If you are instructed to return the micropr ocessor , follow all packaging instructions, and use any packaging materials for shipping that are supplied t o you.
Attention: Do not t ouch the thermal mat erial on the bottom of the heat sink. T ouching the thermal material will contaminat e it. If the thermal material on the micr oprocessor or heat sink becomes contaminated, contact your service t echnician.
Notes: 1. Read the safety information at “Important Safety Information” on page 1. 2. Read “Guidelines for tr ained service technicians” on page 115. 3. Read “Handling static-sensitive devices” on page 117. T o r eplace damaged or contaminated thermal gr ease on the micropr ocessor and heat sink, complete the following steps: 1.
3. T urn off the peripher al devices and disconnect all power cor ds; then, remove the cover (see “Removing and installing the cover” on page 119). Note: When you replace the system boar d, you must either update the server with the latest rmware or rest ore the pr e-existing rmware that the customer pr ovides on a diskett e or CD image.
Installing the system board Note: When you reassemble the components in the server , be sur e t o r oute all cables carefully so that they are not exposed to e xcessive pressur e. Notes: 1. When you r eassemble the components in the server , be sure t o rout e all cables car efully so that they are not exposed to e xcessive pressur e.
Statement 5 CA UTION: The power contr ol button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. T o remove all electrical current from the device, ensure that all power cords are disconnected from the power sour ce.
6. Remove the screw 2 that holds the power supply 1 to the rear of the chassis. 00 00 00 00000000 00000000 00000000 00000000 7. Loosen the captive thumbscr ew 3 that secur es the power supply to the chassis bottom. 8. Lift the power supply out of the bay .
8. T urn off the server and disconnect the ac power cor d. 9. Connect the cables fr om the power supply to the int ernal devices. 10. Install the DIMM air bafe (see “Removing and installing the DIMM air bafe” on page 121). 11. Install the cover (see “Removing and installing the cover” on page 119).
T able 14. Removing the fan 1 F an 1 4 Fan 4 2 F an 2 5 Fan 5 3 F an 3 9. If you ar e instruct ed to r eturn the fan, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a fan assembly T o install the r eplacement fan, complete the following st eps: 1.
b. In the location from which you r emoved the failed fan, rout e the fan cable into its slot 2 in the fan brack et t op. c. Inser t the fan 4 into the br acket 3 . d. Make sure that each of the gr ey soft tabs on the fan is fully seated in its slot in the fan bracket.
Microprocessor Heatsink Orientation DIMMs DIMMs a. Use a ngernail to pr ess the t op of the battery clip away fr om the batt ery . The batt ery pops up when r eleased. b. Use your thumb and inde x nger to lift the batt ery fr om the socket. 6. Dispose of the batt ery as r equired by local ordinances or r egulations.
manufacturer . If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer . The battery contains lithium and can e xplode if not properly used, handled, or disposed of.
Replacing the SAS/SA T A hard disk drive back plate or backplane T o replace the SAS/SA T A har d disk drive backplane or back plat e, complet e the following procedur es: Removing the backplane or back plate (3.
00 00 00 00000000 00000000 00000000 00000000 1 Connect ors 2 Guide channels 1. Connect the power cable to the replacement backplane or back plate. 2. Reconnect the backplane or back plat e cables: • If the server is a hot-swap model, reconnect the SAS/SA T A contr oller signal cable t o the backplane.
Removing the SAS backplane (2.5-inch drives) 1 Alignment tabs 3 Alignment slots 2 Connectors 4 Connectors T o r emove the 2.5-inch drives backplane, complete the following st eps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for tr ained service t echnicians” on page 115.
1 Alignment tabs 3 Alignment slots 2 Drive connect ors 4 Drive connectors 1. Connect the cables to the replacement backplane. 2. Slide the backplane into the car d guides, making sure that any nearby wir es or cables are not tr apped or pinched. 3. Pr ess rmly until the backplane is fully seat ed and clicks int o place.
00 00 00 00000000 00000000 00000000 00000000 6. If the riser -card assembly is an optional PCI-X riser -card assembly, disconnect the riser -card power cable 1 fr om the riser -card assembly . 7. Disconnect any cables from the PCI cards in the riser -card assembly .
5. Carefully align the riser -card assembly with the guides on the r ear of the server and with the riser -card connectors on the syst em boar d; then, pr ess down on the assembly . Make sur e that the riser -card assembly 1 is fully seated in the connector on the system boar d.
6. Disconnect the signal cables that are attached to the SAS/SA T A controller . 7. Grasp the SAS/SA T A contr oller 1 while you pr ess outward on the plastic tabs.
6. T ouch the static-protective package that contains the new ServeRAID-BR10il SAS/SA T A contr oller to any unpaint ed surface on the outside of the server; then, gr asp the contr oller by the t op edge or upper corners of the contr oller and r emove it from the package.
10. Connect the signal cable that is attached t o the drive backplane 1 to the ServeRAID controller connect or 2 . 11. Replace the riser-car d assembly (see “Installing the riser-car d assembly” on page 157). Note: When you restart the server , you are pr ompted to impor t the existing RAID congur ation to the new ServeRAID contr oller .
3. Align the cable connector with the connector on the rear of the DVD drive cage and pr ess the cable connector int o the DVD drive cage connector until it is rmly seated.
5. Connect the DVD drive cable to the syst em board connect or 1 . 6. Reconnect the DVD drive power cable to the power supply cable. 7. Reinstall the DVD drive (see “Replacing a DVD drive” on page 163). 8. Reinstall the riser -card assembly (see “Installing the riser -card assembly” on page 157).
6. If you ar e instructed to return the DVD drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a DVD drive The following not es describe the type of drives that the server supports and other information that you must consider when you install a DVD drive.
CA UTION: When laser products (such as CD-ROMs, DVD drives, ber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposur e t o hazardous laser radiation.
Microprocessor Heatsink Orientation DIMMs DIMMs 4. If you ar e instruct ed t o r eturn the virtual media key, follow all packaging instructions, and use any packaging materials for shipping that are supplied t o you. Installing the virtual media key T o install the virtual media key, complet e the following steps: 1.
Microprocessor Heatsink Orientation DIMMs DIMMs 4. Go to “Completing the FRU r eplacement” on page 172. Replacing the PCI-X riser -card power cable T o r eplace the PCI-X riser-car d power cable, .
7. Disconnect the riser -card power cable from the PCI-X riser car d. 8. If you ar e instructed to r eturn the PCI-X riser-car d power cable, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
3. Copy and unpack the ASU package, which also includes other r equired les, to the server . Make sur e that you unpack the ASU and the r equired les t o the same directory . In addition to the application ex ecutable (asu or asu64), the following les ar e r equired: • F or Windows based operating systems: – ibm_rndis_server_os.
c. Fr om F amily list, select ThinkServer RS210; , and click Continue . d. Click Downloads and drivers . e. Click User's guides and manuals to link to the ASU Users Guide.
– device.cat • F or Linux based oper ating systems: – cdc_interface.sh 4. After you install ASU, T ype the following commands to set the DMI: asu se t S Y S TEM_PROD_DA T A.SysIn f oProdName <m/t_model> [acces s_me thod]asu se t S Y S TEM_PROD_DA T A.
corresponding mapping layer . T o see the Advanced Settings Utility Users Guide . Y ou can access the ASU Users Guide from the L enovo support Web sit e. a. Go to http://www.lenovo.com/support. b. Enter your product number (machine type and model number) or select Servers and St orage from the Select your product list.
5. Update the server conguration (see “Updating the server congur ation” on page 174). 6. Slide the server back into the r ack, if necessary . 7. T urn on the peripheral devices and the server . Connecting the cables The following illustration shows the locations of the input and output connectors on the front of the server .
Updating the server conguration When you start the server for the rst time aft er you add or remove an internal option or e xternal device, you might r eceive a message that the congur ation has changed. The UEFI Setup Utility progr am starts automatically so that you can save the new conguration settings.
Chapter 7. P arts listing, RS210 T ypes 6531, 6532, 6533, and 6534 The following replaceable components are available for the ThinkServer RS210 T ypes 6531, 6532, 6533, and 6534 servers. T o check for an updat ed parts listing on the Web, complete the following st eps: 1.
1 Riser card assembly 12 Bez el 2 DIMM air bafe 13 DVD drive ller 3 DIMM 14 Oper ator information panel 4 P ower supply 15 F ans 5 SAS/SA T A backplane (some models) 16 System board 6 SA T A simple-swap back panel (some models) 17 Micr oprocessor 7 3.
T able 15. P arts listing, T ypes 6531 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 3 Memory module, 2GB DDR3-1333 2Rx8 LP RDIMM (models CT O) 46U199.
T able 15. P arts listing, T ypes 6531 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 11 IBM 146GB 15K 6Gbps SAS 2.5" SFF Slim-HS HDD (models CT O 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12J) 46U2117 11 IBM 500GB 7200 6Gbps NL SAS 2.
T able 15. P arts listing, T ypes 6531 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number Cable, 3.5" SS SA T A Cable (models CT O All Models) 59Y3230.
6531 Software FRU FRU# WS2008 R2 FOUND 64bit GR (models CT O All Models) 90Y1169 WS2008 R2 FOUND 64bit IT (models C T O All Models) 90Y1170 WS2008 R2 FOUND 64bit JP (models CT O All Models) 90Y1171 WS.
T able 16. P arts listing, T ypes 6532 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 2 Air Duct (models CT O All Models) 46C6798 3 Memory module, 1GB .
T able 16. P arts listing, T ypes 6532 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 11 Hard disk drive, 750GB 7200 RPM 3.5" Hot-Swap SA T A II (models C T O 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11J) 45J9646 11 Hard disk drive, IBM 1TB 7200 SA T A 3.
T able 16. P arts listing, T ypes 6532 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 18 Heat Sink (models CT O All Models) 59Y3221 19 T op cover (mode.
T able 16. P arts listing, T ypes 6532 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number ServeRAID M1015 RAID 5 Upgr ade Key (models C TO) 46M0864 ServeRA.
6532 Software FRU FRU# WS 2008 R2 ENT 64bit JP (models C TO All Models) 90Y1196 WS 2008 R2 ENT 64bit SP (models C TO All Models) 90Y1197 WS 2008 R2 ENT 64bit TR (models C TO All Models) 90Y1198 ROK WS2008 FOUND 64bit MUI EN/JP (models CT O All Models) 90Y1199 ROK WS2008 FOUND 64bit MUI EN/FR/GR/SP/IT (models CT O All Models) 90Y1200 T able 17.
T able 17. P arts listing, T ypes 6533 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 8 Hard disk drive, 250GB 7200 RPM 3.5" Simple-Swap SA T A II (models CT O 11G 11M 11A 11J) 45J9634 8 Hard disk drive, 500GB 7200 RPM 3.
T able 17. P arts listing, T ypes 6533 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number Cable, 3.5" SS SA T A cable (models C TO All Models) 59Y3230.
6533 Software FRU FRU# WS2008 R2 FOUND 64bit IT (models C T O All Models) 90Y1170 WS2008 R2 FOUND 64bit JP (models CT O All Models) 90Y1171 WS2008 R2 FOUND 64bit SP (models CT O All Models) 90Y1172 WS.
T able 18. P arts listing, T ypes 6534 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 3 Memory module, 1GB DDR3-1333 1Rx8 LP RDIMM (models CT O) 46U199.
T able 18. P arts listing, T ypes 6534 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 11 Hard disk drive, 146GB 15K 3.5" Hot-Swap SAS (models CT O 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11J 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12J ) 45J9658 11 Hard disk drive, 750GB 7200 RPM 3.
T able 18. P arts listing, T ypes 6534 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 17 Micropr ocessor , Xeon X3450 2.
T able 18. P arts listing, T ypes 6534 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number ServeRAID-MR10i SAS/SA T A Controller (models CT O) 43W4297 Serve.
6534 Software FRU FRU# WS 2008 R2 STD 64bit US (models CT O All Models) 90Y1183 WS 2008 R2 STD 64bit FR (models CT O All Models) 90Y1184 WS 2008 R2 STD 64bit GR (models CT O All Models) 90Y1185 WS 200.
T able 19. Power cords, T ype 6531 Lenovo P ower cor d part number Used in these countries and regions 39M5247 T aiwan 2.8M (models CT O) 39M5102 ANZ 2.8M (models C TO 11M 12M) 39M5123 Europe 2.8M (models C TO) 39M5130 Denmark 2.8M (models CT O 11G 12G) 39M5144 S.
T able 21. Power cords, T ype 6533 Lenovo P ower cor d part number Used in these countries and regions 39M5247 T aiwan 2.8M (models CT O) 39M5102 ANZ 2.8M (models C TO 11M) 39M5123 Europe 2.8M (models C TO) 39M5130 Denmark 2.8M (models C TO 11G) 39M5144 S.
T able 22. P ower cords, T ype 6534 (continued) Lenovo P ower cor d part number Used in these countries and regions 39M5233 Br azil 2.8M (models C TO) 39M5206 China 2.
Chapter 8. Conguring the server The following congur ation pr ograms come with the server: • Setup Utility program The Setup Utility pr ogram is part of the UEFI. Use it t o congur e serial port assignments, change interrupt request (IRQ) settings, change the startup-device sequence, set the date and time, and set passwords.
• Set and change passwords • View and change the startup char acteristics of the server and the order of startup devices (startup-drive sequence) • View and change settings for advanced har dwar.
Ethernet MAC addresses. If you disable a device, it cannot be congured, and the oper ating system will not be able t o detect it (this is equivalent t o disconnecting the device). – P ower Select this choice t o view or change power capping to control consumption, pr ocessors, and performance states.
This choice is on the full Setup Utility menu only . • Start Options Select this choice to view or change the start options, including the startup sequence, keyboar d NumL ock state, PXE boot option, and PCI device boot priority . Changes in the startup options take effect when you start the server .
• L oad Default Settings Select this choice to cancel the changes that you have made in the settings and restor e the factory settings. • Exit Setup Select this choice t o e xit fr om the Setup Utility .
If you forget the administr ator password, you can reset it aft er you change the position of the clear CMOS jumper . Resetting passwords If you forget the power-on password or administrator password,.
T o use the Boot Manager progr am, do the following: Step 1. T urn off the server . Step 2. Restart the server . Step 3. When the prompt <F12> Sel ec t Bo o t Device is displayed, press F12. If a bootable USB mass stor age device is installed, a submenu item ( USB K ey/Disk ) is displayed.
T able 24. RAID conguration utilities (continued) RAID congur ation utility Description Location Where to nd more information LSI Congur ation Utility F or: • IBM ServeRAID-BR10il SAS/SA T A Contr oller • IBM ServeRAID-MR10i SAS/SA T A Contr oller • IBM ServeRAID-M1015 SAS/SA T A contr oller In system rmware.
Note: Appr oximately 1 to 3 minut es aft er the server is connected to ac power , the power -control butt on becomes active. 2. When the pr ompt <F1 Se t up> is displayed, pr ess F1. If you have set an administrat or password, you are prompt ed t o type the password.
Starting the W ebBIOS utility P erform the following st eps to start the WebBIOS utility and access the main menu: 1. After you turn on the power and when the comput er is starting, you are pr ompted to press Ctrl + H when the following message is displayed: Copyr igh t© L SI Logic Corp ora tion Pres s <Ctrl><H> f or WebBI OS 2.
Attention: If you select Clear Conguration or New Conguration , all existing data in the conguration is deleted. Make a backup copy of any data that you want t o keep befor e selecting these options. Clear Conguration Clears the e xisting congur ation.
If you did not receive an EasyStartup DVD with your server , you can download an image from the Lenovo Support Web sit e at: http://w ww.lenovo.com/support The EasyStartup progr am has the following f.
• Initiates an unatt ended installation of the oper ating system and device drivers Setup and congur ation When you start the EasyStartup DVD , you will be prompt ed for the following: • Select the language in which you want to view the progr am.
T ypical operating system installation When you select Install oper ating syst em , you will be prompt ed for information r equired for the installation. The prompts vary depending on the oper ating syst em select ed. This section describes the tasks associat ed with a typical Windows operating system installation.
3. F rom F amily list, select ThinkServer RS210 , and click Continue . 4. Select the oper ating syst em that you want fr om the Oper ating system list, and click Continue . 5. Click Oper ating system installation to download instructions t o install the operating system.
Before distributing the rmwar e update to other servers, ensur e that your server can r estart successfully without encountering hardwar e pr oblems. Starting the backup server rmware The system board contains a backup copy area for the server rmwar e.
Microprocessor Heatsink Orientation DIMMs DIMMs The following table describes the jumpers on the system board. T able 25. System board jumpers Jumper number Jumper name Jumper setting JP1 Clear CMOS jumper 1 • Pins 1 and 2: Keep CMOS data (default).
• DIMM error assistance. The Unied Extensible Firmwar e Int erface (UEFI) disables a failing DIMM that is detected during POS T , and the IMM lights the associat ed system error LED and the failing DIMM error LED . • System-event log (SEL). • ROM-based IMM rmware ash updates.
Y ou also can use the ASU pr ogram to congure the optional r emote pr esence features or other IMM settings. The r emote pr esence featur es pr ovide enhanced syst ems-management capabilities. In addition, the ASU pr ogram pr ovides limited settings for conguring the IPMI function in the IMM thr ough the command-line interface.
Note: This specic version is requir ed. 5. Use Windows Update t o install all available critical updates. 6. Launch the EasyManage installation. 7. After ThinkServer EasyManage is installed, enable Security and P atch Manager to obtain the LANDesk 8.
Uninstalling the LANDesk Software Agent If the Core Server has LANDesk agents on it fr om a pr evious Management Suite r elease, it will fail the autorun prer equisite check. Y ou must r emove the old agents by running uninstallwinclient.ex e le from the Pr ogram FilesLANDeskManagementSuit e folder .
Step 2. When the prompt <F1> Se tup is displayed, pr ess F1. (This pr ompt is displayed on the screen for only a few seconds. Y ou must pr ess F1 quickly .) If you have set both a power -on passwor d and an administr ator passwor d, you must type the administr ator password t o access the full Setup utility menu.
Note: Changes are made periodically to the L enovo W eb site. The actual pr ocedure might vary slightly from what is described in this document. 1. Go t o http://www.lenovo.com/support. 2. Enter your pr oduct number (machine type and model number) or select Servers and Storage fr om the Select your pr oduct list.
g. Select Exit Setup ; then, pr ess Ent er . h. Make sur e that Y es, exit the Setup Utility is select ed; then, press Enter . 220 Har dware Maint enance Manual.
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local L enovo repr esentative for information on the pr oducts and services curr ently available in your area.
T rademarks The following terms are tr ademarks of Lenovo in the Unit ed States, other countries, or both: Lenovo Lenovo logo ThinkServer The following terms ar e tr ademarks of International Business.
Pr oduct recycling and disposal This unit must be r ecycled or discarded according to applicable local and national r egulations. L enovo encourages owners of information technology (IT) equipment t o r esponsibly r ecycle their equipment when it is no longer needed.
Compliance with Republic of T urk ey Directive on the Restriction of Hazardous Substances Meets r equirements of the Republic of T urkey Dir ective on the Restriction of the Use of Certain Hazardous Substances In Electrical and Electr onic Equipment (EEE).
Battery r eturn pr ogram This pr oduct may contain a lithium or lithium ion battery . Consult your user manual or service manual for specic batt ery information. The battery must be r ecycled or disposed of pr operly . Recycling facilities may not be available in your area.
and accumulators on the envir onment and human health due to the potential presence of hazar dous substances. F or pr oper collection and treatment, go to http://www.lenovo.com/lenovo/environment. F or California: P erchlor ate material - special handling may apply .
United Kingdom t elecommunications safety requir ement Notice to Customers This appar atus is approved under appr oval number NS/G/1234/J/100003 for indirect connection to public telecommunication systems in the Unit ed Kingdom.
Dieses Ger ät ist ber echtigt, in Über einstimmung mit dem Deutschen EMVG das EG-Konformitätsz eichen - CE - zu führen. V erantwortlich für die Konformitätserklärung nach P aragr af 5 des EMVG ist die L enovo (Deutschland) GmbH, Gropiusplatz 10, D-70563 Stuttgart.
P eople's Republic of China Class A warning stat ement K orea Class A warning statement Appendix A. Notices 229.
230 Har dware Maint enance Manual.
.
Part Number: RS210 Printed in USA (1P) P/N: RS210 *RS210*.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lenovo 6531 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lenovo 6531 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lenovo 6531, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lenovo 6531 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lenovo 6531, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lenovo 6531.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lenovo 6531. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lenovo 6531 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
