Manuel d'utilisation / d'entretien du produit PWC18E14.7 du fabricant Lennox International Inc.
Aller à la page of 41
INSTALLATION AND MAINTENANCE INSTRUCTIONS PWC Series "Magic-Pak" Self-Contained Heat Pump [ WARNING Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified installer or service agency.
INSTALLATION General =.se instructions explain the recommended method of ,llation of the PWC heat pump unit and associated e_uctrical wiring. the unit inside the carton if the carton is damaged. File a cfaim with the transportation company. If any damages are discovered and reported to the carrier DO NOT INSTALL THE UNIT, as claim may be denied.
If the unit is installed in a residential garage, it must be located or protected to avoid physical damage by vehicles. The unit must be installed so that no electrical compo- nents are exposed to water. I [A CAUT,ON ] This unit must be installed level to allow for proper drainage of the chassis base pan and unit drain pan.
Application Limitations Air Filter Outdoor Ambient Air Temperature °F Minimum DB - Cooling Maximum DB Cool Heat 65 125 75 Indoor Ambient Air Temperature °F I Minimum Maximum DB/WB DB DB,_VB DB Cool .
Use wiring with a temperature limitation of 75 = C mini- mum. Run the 208 or 230 volt, 60 hertz electric power supply through a fused disconnect switch to the control box of the unit and connect as shown in the wiring dia- gram located on the inside of the control access panel.
After closing test pins and appropriate cycle time has elapsed, the reversing valve should shift to defrost mode and the outdoor fan should stop. After 2 seconds of defrost operation, the reversing valve should shift back to ",ting operation and the outdoor fan should start.
208/230-1-60 POWER SUPPLY WITH MIN. 75"C COPPER WIRE I CIRCUIT1 I I (lo_cO_L'qCIRCUIT2 I •; . .; : : P_D BLACK LOWER MOTORvloI_r r RED UNE VOLTAGE-FACTORY UNE VOLTAGE-RELD .
208/230-1-60 :OWER SUPPLY WITH MIN. 75"C COPPER WIRE I CIRCUIT 1 I CIRCUIT 2 : i : : : • RED F_ UNE VOLTAGE-FACTORY ..... LINE VOLTAGE-RELD ....
208/230-1-60 POWER SUPPLY WITH MIN. 75"C COPPER WIRE LINE VOLTAGE-FACTORY ..... UNE VOLTAGE-FIELD ........ UNE VOLTAGE-FI ELD (IF USED) LOW VOLTAGE-FACTORY THERMOSTAT .......... LOW VOLTAGE-FIELD NOTE: IF ANY OF THE ORIGINAL WIRES ARE REPLACED, THE SAME SIZE AND TYPE WIRE MUST BE USED.
I Limited Warranty August 1, 1997 This warran(y gives you specific legal rights and you may have other rights which vary from state/province to state/province.
INSTALLATION INSTRUCTIONS Wall Sleeve Kit CA239 For Use With HW/HWC/EWC/PWC Series Magic-Pak Thru-the-Wall Unit age_ _WARNING Parts List Quantity Description 1 Top Panel 1 Bottom Panel 1 Right Side Pa.
INSTALLATION Wall Sleeve Assembly To assemble the wall sleeve, refer to the following instruc- tions and Figure 1. 1. Slide top panel over side panels until retaining clips are engaged in slotted openings.
Further sealing against air infiltration must be done alter the Magic-Pak unit is installed in the wall sleeve and utility connections have been completed (see Sealing/Weath- erproofing Wall Sleeves section). Wall Sleeve Installation The wall sleeve may be installed from either the inside or outsideof the building.
I _A_T_°. I 4"948°96----I I INSTALLATION AND MAINTENANCE INSTRUCTIONS PWC SERIES SELF-CONTAINED HEAT PUMP Manufactured By ARMSTRONG AIR CONDITIONING INC.
I PART.O I .,,,,RO.. I OATE 12''0 I SUPERSEOES I I PAGE2OF,0 GENERAL These instructions explain the recommended method of installation of the PWC heat pump unit and associated elec- trical wiring. This unit is designed and approved for use as a self-contained air to air heat pump system.
PARTNO. I 41194BOg6 I DATE I 2-1-96 I SUPERSEDES I 411940094 I PAGE3OFIO I LOCATION The design is certifiedfor through-the-wall installation only. The interior portions of the unit may be surrounded by a closet with clearances to combustible material held to 0" at sides, 0" top and O" front of the plenum.
PA.T.O. I ,,,,_,,.0_, I 0','_ I _'"_ I SU"ERSEOES I ""_"00_" I PA_E,'O_,O FIGURE 1 INSTRUCTION FORSUPPORTING PWCUNITS Wall Sleeve 7 x 22 Min. Opening To A#ign with'Return Air Opening in Unit. Vibration Isolating Material % Plywood FIGURE2 DRAIN PAN 5/8 " I.
.ARTNO. I "f9"Bog I OATE I 2"t'g6 I .SUPERSEOES I 4119'0094 [ PAGESOFtO LIMITATIONS The unit should be installed in accordance with all national and local safetycodes. Limitations of the unit and appropriate accessories must also be observed.
I PA.TNo I .tt9..o96 I DATE 12196 I SUPERSEDES I ,rig.DO9. I PAGE,O. tO It an installation is made in which it is more desirable to mount the filter exterior to the unit, in the return duct work, or olherwise, either the permanent filter supplied or a disposable filter may be used.
PA...o, I .,,9.o09. I IDNSTALLATION AN MAINTENANCE INSTRUCTIONS PWC SERIES SELF-CONTAINED HEAT PUMP PART NO. ] 4,,94°O94 I OA_E ] 4-,5-94 I SU_RSEOES I .EW I _'AGE_O_IO I Manulaclured By ARMSTRONG AIR CONDITIONING INC, A LENNOX International Inc.
! PART NO. I 4,tg4ooB4 I DATE I 4lsg, I SUPERSEOES I NEW I PAGE2OFlO GENERAL Theseinstructions explainthe recommended method of installation of the PWC heal pump unit and associated elec- trical wiring. This unil is designed and approved for use as a self-contained air Io air heat pump system.
I PA,,NO. I ,, g,o094 I DATE I '-fS-g' I SUPERSEDES I ,EW I PAGE3OF,O LOCATION The design is certified for through-the-wall installation only. The interior portions of the unit may be surrounded by a cJoset with clearances to combustible material held to O" at sides, 0" top and 0" front of the plenum.
I PART.O. I "(940094 [ DArE I 4-_5-9' I SUPERSEDES NEW [ PAGE 4 OF 10 FIGURE 1 INSTRUCTION FOR SUPPORTING PWC UNITS Wall Sleeve 7 x 22 Mio. Opening To Align with Return Air Opening _n Unit. ] L_ Vibration isolating Material % FIGURE 2 5/8 "I.
PA,TNO I 4tt94OOB4 I DA E I 41594 ]SUPERSEDES I NEW I PAGE OFtO LIMITATIONS The unit should be installed in accordance with all national and local safety codes. Limitations of the unit and appropriate accessories must also be observed. Theunit must NOTbe installed with any ductwork in the outdoor airstream.
PART NO. ] 41194D094 ] DATE ] 4-15-94 ] SUPERSEDES ] NEW ] PAGE 6 OF 10 If an installation is made in which it is more desirable to mount the filter exterior to the unit, in the return duct work, or otherwise, either the permanent filter supplied or a disposable filter may be used.
PA,T,O. I ,tt,,O0,, ( [ l SUPERSEOES I NEW l PAGE OFtO The defrost control will initiate a defrosl cycle if the time period has elapsed and the defrost sensor detects a temperature below freezfng.
[ PARTNO I 4t_g4DOg4 I DATE ] 4iS-g, I SUPERSEOES I NEW I RAGE8OF_O MAINTENANCE NORMAL MAINTENANCE WARNING: PRIOR TO ANY OF THE FOLLOWING MAINTENANCE PROCEDURES SHUT OFF ALL ELECTRICAL POWER TO THE UNIT.
I _,,9_Do9. I OA_E l .-_5-g_ l SU_E.SEOES l .EW I ,_GEgOF,O CAP. _EE EV.OV_ RED UOI'CR VZOI.[T HIGH Rm U B.UE ?AND 10 PVC 0NLY lira >( CmTm m.L0W C/P/Z:IT_-RIJ_ eTI O / RE9 8L_X llllll llllll V/I.
I PAGE 10 OF 10 1PA'_RT N0. I 411941)094 I DATE I 4-15-94 I SUPERSEDES I NEW 3Ct/'ZsO- t-60 SUPPLT WI?H ¥[N. 75'€ €_ WIIaE _ LINK; tOLTAE_'II_O CX_Z:_zT t i _ cz_qcuzT 2 ) -- -- Lof vo.T_4[_ HZOH Ot.UE VXa.k'T €_rxcTOR aU_a_ Yn.
,! PWC SELF CONTAINED THRU-THE-WALL HEAT PUMP Part No. 30790F08g Date 6-1-69 Supersedes 30790G082 Page_of 12 Installation and Maintenance Instructions _O, MSTP_,.
Part N_ 30790F089 $upereedes 30790G082 Date. 6-1-89 Page2__2__of 12 FORWARD This is a self-contained heat pump designed for Installation through an exterior wall. The unit is Underwriters' Laboratories listed under heat pumps and is in compliance with Underwriters Standard, UL 559.
PartNo. 307SOF089 Supersedes 30790G082 Date 6-1-89 Page _of 12 INTRODUCTION This manual is intended to familiarize the installer, serviceman, and the user with the installation, operation and maintenance of this thru-the-wall heat pump. This unit is shipped from the factory in one package completely assemblied and wired.
Part No. 30?90F089 Date 6-149 Supersedes 30790G082 ,, Page _of 12 TABLE OF CONTENTS " Page INSTALLATION Site Preparation ............................ 5 Condensate and Defrost Drain ................. 6 Electrical Connections ......................
Part No. 307g0F089 Supersedes 30790G082 Date. 6-1-89 Page_of 12 INSTALLATION Site Preparation Tills unit is approved for thru-the.wall installation, with zero clearance to combustible material.
Part No. 30790F089 Date 6-1-89 Supersedes 30790G082 Page_of 12 INSTALLATION Before sliding unit into sleeve, remove 5 screws and washers from top panel. Slide unit into sleeve until the angle on top of the unit lines up with the top flange of the sleeve, and should almost touch.
Pan No. 307g0F089 Supemedes 30790G082 Date 6-1_9 Page T of 12 INSTALLATION Electrical Connections All wiring to unit must comply with the national Electrical Code NFPA No. 70 or local codes, where they prevail. ANY ALTERNATION OF INTERNAL WIRING CAN VOID UNDERWRITER'S APPROVAL, ARI CER- TIFICATION AND MANUFACTURE'S LIMITED WARRANTY.
Part No. 30790F089 Supersedes 30790G082 Date 6-1-89 Page _ of 12 FIGURE 3. SINGLE ENTRY SUPPLY [] 208-230 voit 1 Ph. power supply I I I Remove internal for multiple entry Supply. PWC18E4.8, PWGI8E7.2 PWC24E4.8, PWC24E7.2 208-230V 1 Ph. power supply t-_ Circuit I "_ I Circuit I No.
Part No. 30790F089 Date 6-1-89 Supersedes 30790G082 Page_of 12 Thermostat This unit requires special thermostat for operation. See product specification sheets or label on unit for manufacture's part number. Install the thermostat according to directions furnished with It.
Part No. 30790F089 Supersedes 30790G082 Date 6-1-89 Page 10 of 12 INSTALLATION A. Unit Check-Out Procedure - IMPORTANT 1. Filter(s) must be clean and in place as to filter all air passing over 2. Set thermostat to "OFF" position. 3. Check that correct size fuses are installed for unit.
Part No. 30790F089 Supersedes 30790G082 Date. 6-1-89 Page 11 of 12 OPERATION INSTRUCTIONS The following instructions are to be followed to obtain years of trouble free operation of your year-around comfort system. To start unit turn on main power (may have two disconnect switches).
Part No. 30790F089 Supersedes 30790G082 Date, 6-1o89 Page 11 of 12 OPERATION INSTRUCTIONS The following instructions are to be followed to obtain years of trouble free operation of your year-around comfort system. To start unit turn on main power (may have two disconnect switches).
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Lennox International Inc. PWC18E14.7 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Lennox International Inc. PWC18E14.7 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Lennox International Inc. PWC18E14.7, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Lennox International Inc. PWC18E14.7 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Lennox International Inc. PWC18E14.7, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Lennox International Inc. PWC18E14.7.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Lennox International Inc. PWC18E14.7. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Lennox International Inc. PWC18E14.7 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
