Manuel d'utilisation / d'entretien du produit WS-7016U du fabricant La Crosse Technology
Aller à la page of 38
i WS-7016U Wireless 433 MHz Temperature Station Instruction Manual.
ii TABLE OF CONTENTS Topic Page Inventory of Contents 1 Additional Equipment 1 Quick Setup 2 Detailed Setup Guide Battery Installation 3-6 Remote Control Sender 3-4 Indoor Temperature Station 5-6 Sett.
iii Remote Control Sender 13-16 Indoor Temperature Station 16-18 Using Multiple Remote Control Senders Setup of Multiple Units 18-21 Viewing Remote Control Senders 21-22 Features of the Multiple Remot.
1 INVENTORY OF CONTENTS 1. The Indoor Temperature Station (Figure 1) 2. The Outdoor Remote Control Sensor (TX3U) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double si ded adhesive tape. 5. Instruction Manual a nd Warranty Card.
2 QUICK SETUP 1. Insert two AAA batteries into the Rem ote Control Sender. 2. Insert two AA batteries into the Indoor Temperature Station. 3. Wait 5-6 minutes, or until the outdoor temperature is displayed in the OUTDOOR LCD (Liquid Crystal Display) of the Indoor Temperature Station.
3 DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE CONTROL SENDER 1. Remove the m ounting bracket. The bracket snaps on and off with minim al effort. 2. Remove battery cover. To do this, remove the flathead screw located in the lower-central position of the unit.
4 battery cover to fall away from the unit. Place the screw partially back into the hole and angle it slightly, so the threads grab the battery cover. With the screw, pull the battery cover off. 3. Observing the correct polarity, install 2 AAA batteries.
5 B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. 1. Remove the battery cover on the backside. To do this, push up and pull out.
6 2. Observing the correct polarity, install 2 AA batteries. 3. Replace battery cover. 4. Wait 5-6 minutes or until both indoor and outdoor temperatures are shown on the Indoor Temperature Station. 5. The Indoor Temperature Station should now show: “-:- -” in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’s.
7 II. TIME A. SETTING THE TIME 1. Press and hold the SET button for 1 second. “12h” will appear in the TIME LCD. 2. Use the INDOOR button to select either 12h time or 24h time (12h is an AM—PM mode, and 24h is military time). 3. Press the SET button 2 times, “TIME” will flash in the upper left corner.
8 5. Press the SET button to activate the clock. Note: There is only a “PM” display, which appears under “TIME.” If there is no display here it is AM. Make sure you set the time accordingly. III. UNITS OF TEMERATURE MEASURE A. SELECTING UNITS OF MEASUREMENT 1.
9 IV. FEATURES A. INDOOR MINIMUM AND MAXIMUM TEMPERATURES 1. Press and hold the INDOOR button for 1 second. “MIN” appears in the INDOOR LCD and the recorded minim um temperature is displayed. 2. Press and hold the INDOOR button for 1 second. “MAX” appears in the INDOOR LCD and the recorded maxim um temperature is displayed.
10 B. OUTDOOR MINIMUM AND MAXIMUM TEMPERATURES 1. Press and hold the OUTDOOR button for 1 second. “MIN” appears in the OUTDOOR LCD. The “OUTDOOR MIN,” and “TIME” displays will flash. The recorded minim um temperature is displayed in the OUTDOOR LCD, and the time it was recorded is displayed in the TIME LCD.
11 displayed in the OUTDOOR LCD, and the time it was recorded is displayed in the TIME LCD. After 15 seconds the “OUTDOOR MAX,” and “TIME” will stop flashing, and the maxim um outdoor temperature will continue to be displayed. 3. To return to current temperature, press and hold the OUTDOOR button for 1 second.
12 temperatures are reset release the buttons. 2. To return to the current indoor temperature, press and hold the INDOOR button two times, holding for 1 second each. B. OUTDOOR 1. To reset both the minimum and max imum t empe rat ur es— pre ss and continue to hold the OUTDOOR button, while you press and hold the RESET button.
13 VI. READING THE TEMPERATURE TREND A. The temperature trend indicator is displayed in the OUTDOOR LCD. 1. Ï Indicates that the tem perature is rising. 2. Ð Indicates that the tem perature is dropping. 3. The absence of an arrow indicates that the temperature is stable.
14 walls, concrete, and large metal objects can reduce the range. Place both units in their desired location before permanently mounting the Remote C ontrol Sender.
15 c) Where marked, drill holes into mounting surface using an appropriate size drill bit. d) Screw mounting bracket onto the mounting surface. Ensure that the screws are flush with the bracket.
16 c) Remove the protective strip from the other side of the tape. Position the Remote Control Sender in the desired location, ensuring that the Indoor Temperature Station can receive the signal.
17 1. USING THE TABLE-STAND a) The Indoor Temperature Station comes with the table stand already mounted. If you wish to use the table- stand all that is required is to place the Indoor Temperature Station in an appropriate location.
18 a) Remove the table stand. To do this, pull down on the stand from the rear and rotate forward. b) Fix a screw (not included) into the desired wall, leaving approximately 3/16 of an inch (5mm ) extended from the wall. c) Place the Indoor Temperature Station onto the screw using the hanging hole on the backside.
19 offers the same plus a 10’ probe to insert in a pool, spa, soil, etc.). Assign a number to each Remote Control Sender (i.e. #1 will be for outdoors, #2 will be for the basement, etc.). This will help you determine which temperature, from which Sender, you are reading on the Indoor Temperature Station.
20 A. SETUP OF MULTIPLE UNITS 1. It is necessary to remove the batteries from all existing units in operation. 2. Remove the battery covers to all Remote Control Senders. See section I.A.2. 3. Place all Remote Control Senders in sequential order. 4. In sequential order, install batteries.
21 1 5. Install batteries into the Indoor Temperature Station. (Refer to instructions in I.B. ). 6. Follow directions in section II.A to set the time, section III.A to select Fahrenheit or Celsius, and section VII. A to mount. B. VIEWING MULTIPLE REMOTE CONTROL SENDERS ON THE INDOOR TEMPERATURE STATION 1.
22 3. Repeat step 1 to view the 3 rd , 4 th , and 5 th (depending on how many are set up) temperatures sent by the Remote Control Senders. Continue to press RESET until you return to the first Remote Control Sender. C. VIEWING THE FEATURES OF MULTIPLE REMOTE CONTROL SENDERS 1.
23 the ir mini mum an d max imum temperatures. 3. To reset the OUTDOOR MINIMUM AND MAXIM UM TEMPERATURES, follow step 1 above and the directions in sections V.A. through V.B. T h i s will reset the minim um and maxim um for only the selected Remote Control Sender.
24 TROUBLESHOOTING Problem Solution “--. -” appears in the OUTDOOR LCD of the Indoor Temperature Station. Batteries may be inserted wrong in Remote Control Sender— correct the polarity The batteries may be weak— replace with new batteries. The Remote Control Sender may be out of its 80 foot (25m) range—bring the units closer together.
25 “--.-” appears in the OUTDOOR LCD of the Indoor Temperature Station. (continued) Obstacles such as walls, concrete, metal window frames, or large metal objects, may be obstructing signal transmission from the Remote Control Sender—Relocate the Remote Control Sender, within range, where there are no obstructions.
26 No temperature in the LCD of the Remote Control Sender. The batteries may be inserted wrong or weak—check the polarity of batteries or replace with new batteries. Remote Control Sender out of its 80 foot (25m) range—bring the units closer together.
27 The LCD of the Indoor Temperature Station is blank. (continued) Contact La Crosse Technology for replacement. Temperature is “incorrect” Temperatures can vary depending on the location of the Remote Control Sender. The thermometers are not 100% accurate (the WS-7016U is accurate to +/- 2 ° F).
28 Problem not covered under the warranty (ie. Dropped unit into water). Call La Crosse Technology to order replacement part. We will accept Visa, MasterCard, Discover, or prepayments by check. MAINTENANCE AND CARE INSTRUCTIONS • Extreme tem peratures, vibration, and shock should be avoided to prevent damage to the units.
29 • Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology repairs. SPECIFICATIONS Transmitting Frequency 433MHz Recommended Operating Temperature.
30 Remote Control Sender -21.8 ° F to 156.2 ° F with 0.2 ° F resolution. (-29.9 ° C to 69.0 ° C with 0.1 ° C resolution). Accuracy Indoor +/- 2 ° F (+/- 1 ° C). Outdoor +/- 2 ° F (+/- 1 ° C). Transmitting range of the Remote Control Sender Maximum 80 feet (25m).
31 Battery life expectancy for both units Approximately 1 year. Dimensions: (L x W x H) Indoor Temperature Station 3.51 x 1.19 x 4.88 in. (excluding table stand) (90 x 30.
32 WARRA NTY INFORMA TION La Crosse Technology, Ltd provides a 1-year limited warranty on this product agai nst manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid onl y on products purchased and used in North America and only to the original purchaser of this product.
33 covered by this warranty . If necessary repairs are not covered by this warranty , or if a product is examined which is not in need or repair, you will be charged for the repairs or examination.
34 the seller or performance variations resulting from installation-related circumstances. LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT.
35 support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacro ss etechnology.com FCC DISCLAIMER This device complies with part 15 of the FCC rules.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté La Crosse Technology WS-7016U c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du La Crosse Technology WS-7016U - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation La Crosse Technology WS-7016U, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le La Crosse Technology WS-7016U va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le La Crosse Technology WS-7016U, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du La Crosse Technology WS-7016U.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le La Crosse Technology WS-7016U. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei La Crosse Technology WS-7016U ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
