Manuel d'utilisation / d'entretien du produit I2778VHE6 du fabricant AOC
Aller à la page of 71
LCD Monitor User Man ual I2778VHE6 (LED Backlight) www .aoc.com ©2014 AOC.All Rights Reserved..
1 Safety ................................................................................................................................................................ 3 National Conventions ..........................................................
2 Regulation ....................................................................................................................................................... 59 FCC Notice ........................................................................
3 Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and W arnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
4 Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company . The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.
5 Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product.
6 Cleaning Clean the cabinet regularly with cloth. Y ou can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
7 Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
8 Setup Contents in Box Monitor CD Manual Power Cable Monitor Base * * * Analog Cable DVI Cable HDMI Cable * Not all signal cables (Analog, DVI, HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch ofce for conrmation.
9 Setup Stand & Base Please setup or remove the base following the steps as below . Setup: Remove:.
10 Adjusting V iewing Angle For optimal viewing it is recommended to look at the full face of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle.
11 Connecting the Monitor Cable Connections In Back of Monitor and Computer: 3 4 5 2 1 1. AC port 2. HDMI 3. DVI 4. Analog (D-Sub 15-Pin VGA cable) 5. Earphone T o protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor .
12 W all Mounting Preparing to Install An Optional W all Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately . Disconnect power before this procedure. Follow these steps: 1. Remove the base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm.
13 AOC Anti-Blue Light Feature Description Studies have shown that just as ultra-violet rays can cause eye damage, blue light rays from LED displays can cause damage to different parts of the eye and af fect vision over time.
14 Adjusting Setting Optimal Resolution Windows 8 For Windows 8: 1. Right click and click All apps at the bottom-right of the screen. 2. Set the “View by” to “Category” .
15 4. Click DISPLA Y . 5. Set the resolution SLIDE-BAR to Optimal preset resolution. Windows 7 For Windows 7: 1. Click ST ART . 2. Click CONTROL P ANEL .
16 3. Click Appearance . 4. Click DISPLA Y . 5. Set the resolution SLIDE-BAR to Optimal preset resolution.
17 Windows V ista For Windows Vista: 1. Click ST ART . 2. Click CONTROL P ANEL . 3. Click Appearance and Personalization . 4. Click Personalization.
18 5. Click Display Settings . 6. Set the resolution SLIDE-BAR to Optimal preset resolution.
19 Windows XP For Windows XP: 1. Click ST ART . 2. Click SETTINGS . 3. Click CONTROL P ANEL . 4. Click Appearance and Themes . 5. Double click DISPLA Y .
20 6. Click SETTINGS . 7. Set the resolution SLIDE-BAR to Optimal preset resolution Windows ME/2000 For Windows ME/2000: 1. Click ST ART . 2. Click SETTINGS .
21 Hotkeys 1 Source/Auto/Exit 2 Clear vision /< 3 V olume / > or 4:3 / Wide / > 4 Menu/Enter 5 Power Power Press the Power button to turn on/off the monitor . V olume / > When there is no OSD, press > adjust volume(only HDMI). 4:3 or wide / > When there is no OSD, press > continuously to change 4:3 or wide image ratio.
22 Clear Vision 1. When there is no OSD, Press the “<” button to activate Clear Vision. 2. Use the “<” or “>” buttons to select between weak, medium, strong, or off settings.
23 OSD Setting Basic and simple instruction on the control keys. Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press the -button to activate the OSD window . 2.
24 Luminance Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press (Menu) to display menu. Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit Contrast 50 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode 2.
25 Luminance Image Setup 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Color Setup Picture Boost OSD Setup Extra Exit Contrast 50 4. Press < or > to adjust. Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit Contrast 50 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode 5.
26 Image Setup Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Color Setup Picture Boost Exit Extra Clock 50 50 50 50 50 Phase H.
27 Luminance OSD Setup Color Setup Picture Boost Exit Extra 50 50 50 50 Phase H.Position V .Position Sharpness Image Setup 50 Clock 4. Press < or > to adjust. Luminance OSD Setup Color Setup Picture Boost Exit Extra Clock 50 50 50 50 50 Phase H.
28 Color Setup Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Color Setup Picture Boost Exit Extra Image Setup 50 Red Color T emp.
29 Luminance OSD Setup Color Setup Picture Boost Exit Extra Image Setup 50 Red 50 Green DCB Mode off 50 Blue DCB Demo off Color T emp. Warm 4. Press < or > to adjust. Luminance OSD Setup Color Setup Picture Boost Exit Extra Image Setup 50 Red Color T emp.
30 Picture Boost Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Picture Boost Exit Extra Image Setup 50 Contrast 50 H.
31 Luminance OSD Setup Picture Boost Exit Extra Image Setup 50 Contrast 50 H. position 50 Frame Size 50 V .position 50 Brightness Color Setup Bright Frame off 4. Press < or > to adjust. Luminance OSD Setup Picture Boost Exit Extra Image Setup 50 Contrast 50 H.
32 OSD Setup Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Exit Extra Image Setup 0 25 Transparence 10 Timeout Language English Break Reminder H.
33 Luminance OSD Setup Exit Extra Image Setup 0 25 Transparence 10 T imeout Break Reminder H. position V .position 50 Color Setup Picture Boost off Language English 4. Press < or > to adjust. Luminance OSD Setup Exit Extra Image Setup 0 25 Transparence 10 Timeout Language English Break Reminder H.
34 Extra Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press (Menu) to display menu.
35 Luminance Exit Extra Image Setup Color Setup Picture Boost OSD Setup Image Ratio DDC-CI Auto Config Yes Reset Off timer 00 wide Yes NO Resolution: 1920(H)x1080(V) H. Frequency: 67KHz V . Frequency: 60Hz Input Select DVI 4. Press < or > to adjust.
36 Exit Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Contrast 50 1. Press (Menu) to display menu. Luminance Exit Image Setup Color Setup Picture Boost OSD Setup Extra 2. Press < or > to select (Exit), and press to exit.
37 LED Indicator Status LED Color Full Power Mode Green Active-off Mode Orange.
38 Driver Monitor Driver Windows 8 1. Start Windows® 8 2. Right click and click All apps at the bottom-right of the screen. 3. Click on the “Control panel” icon 4.
39 5. Click on the “Display” icon. 6. Click on the “Change display settings” button. 7. Click the “Advanced Settings” button..
40 8. Click the “Monitor” tab and then click the “Properties” button. 9. Click the “Driver” tab. 10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver ... “ and then click the "Browse my computer for driver software" button.
41 1 1. Select "Let me pick from a list of device drivers on my computer" . 12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:Drivermodule name (where X is the drive letter designator for the CD-ROM drive).
42 Windows 7 1. Start Windows® 7 2. Click on the 'Start' button and then click on 'Control Panel' . 3. Click on the 'Display' icon.
43 5. Click the “Advanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button. 7. Click the “Driver” tab.
44 8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver ... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device drivers on my computer" .
45 Windows V ista 1. Click "Start " and "Control Panel ". Then, double-click on "Appearance and Personalization" . 2. Click "Personalization" and then "Display Settings" . 3. Click "Advanced Settings.
46 4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the conguration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the gure below , click "Continue" .
47 Windows XP 1. Start Windows® XP 2. Click on the 'Start' button and then click on 'Control Panel '. 3. Select and click on the category ‘Appearance and Themes’ 4.
48 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your monitor is properly congured. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button.
49 8. Select the 'Install from a list or specic location [advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
50 Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
51 i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor .
52 e-Saver Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).
53 Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a dif ferent window . Y ou only need to drag the window to a corresponding pane, when you want to access it.
54 T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor . No images on the screen • Is the power cord connected properly? Check the power cord connection and power supply .
55 Specication General Specication Panel Model name I2778VHE6 Driving system TFT Color LCD Viewable Image Size 68.6 cm diagonal Pixel pitch 0. 31 1 mm(H) x 0. 31 1 mm(V) Video R, G, B Analog lnterface & DVI, HDMI interface Separate Sync. H/V TTL Display Color 16.
56 Preset Display Modes ST ANDARD RESOLUTION HORIZONT AL FREQUENCY(kHZ) VERTICAL FREQUENCY(Hz) VGA 640×480 @60Hz 31.469 59.94 640×480 @72Hz 37.861 72.809 640×480 @75Hz 37.5 75 MAC MODE VGA 640 × 480@67Hz 35 66.667 IBM-MODE DOS 720×400@70Hz 31.469 70.
57 Pin Assignments 15-Pin Color Display Signal Cable Pin Number Signal Name Pin Number Signal Name Pin Number Signal Name 1 Video-Red 6 GND-R 11 N.C. 2 Video-Green 7 GND-G 12 DDC-Serial data 3 Video-Blue 8 GND-B 13 H-sync 4 N.C. 9 +5V 14 V -sync 5 Detect Cable 10 Ground 15 DDC-Serial clock 24-Pin Color Display Signal Cable Pin No.
58 19-Pin Color Display Signal Cable Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TMDS Data 2+ 9 TMDS Data 0- 17 DDC/CEC Ground 2 TMDS Data 2 Shield 10 TMDS Clock + 18 +5V Power 3 TMDS Data 2- 11 TMDS Clock Shield 19 Hot Plug Detect 4 TMDS Data 1+ 12 TMDS Clock - 5 TMDS Data 1Shield 13 CEC 6 TMDS Data 1- 14 Reserved (N.
59 Regulation FCC Notice FCC Class B Radio Frequency Interference Statement W ARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
60 WEEE Declaration Disposal of W aste Equipment by Users in Private Household in the European Union. This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.
61 EP A Energy Star ENERGY ST AR® is a U.S. registered mark. As an ENERGY ST AR® Partner , AOC International (Europe) BV and Envision Peripherals, Inc.
62 TCO DOCUMENT.
63 Service W arranty Statement for Europe LIMITED THREE-YEAR W ARRANTY* For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V . warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase.
64 All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards. If your warranty has expired, you still have access to all available service options, but you will be responsible for the cost of service, including parts, labor , shipping (if any) and applicable taxes.
65 W arranty Statement for Middle East and Africa (MEA) And The Commonwealth of Independent States (CIS) LIMITED ONE to THREE YEARS W ARRANTY* For AOC LCD Monitors sold within the Middle East and Africa (MEA) and the Commonwealth of Independent States (CIS), AOC International (Europe) B.
66 This limited warranty does not cover any of the product rmware or hardware that you or any third party have modied or altered; you bear the sole responsibility and liability for any such modications or alteration. All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
67 AOC International (Europe) B.V . Prins Bernhardplein 200 / 6th oor , Amsterdam, The Netherlands T el: +31 (0)20 504 6962 • Fax: +31 (0)20 5046933 AOC PIXEL POLICY ISO 9241-307 CLASS 1 July 25 th , 2013 AOC strives to deliver the highest quality products.
68 W arranty Statement for North & South America (excluding Brazil) W ARRANTY ST A TEMENT for AOC Color Monitors Including those Sold within North America as Specied Envision Peripherals, Inc.
69 ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE) ARE LIMITED IN DURA TION TO A PERIOD OF THREE (3) YEARS FOR P ARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD P ANEL FROM THE ORIGINAL DA TE OF CONSUMER PURCHASE.
70 EASE PROGRAME E A S E P R O G R A M Only for AOC branded monitors sold within the continental United States. All AOC branded monitors are now covered by the EASE Program. If your monitor malfunctions at any time during the rst three months, AOC will provide a replacement monitor within 72 hours after you are approved for our program.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté AOC I2778VHE6 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du AOC I2778VHE6 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation AOC I2778VHE6, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le AOC I2778VHE6 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le AOC I2778VHE6, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du AOC I2778VHE6.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le AOC I2778VHE6. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei AOC I2778VHE6 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
