Manuel d'utilisation / d'entretien du produit KX200.4 du fabricant Kicker
Aller à la page of 20
KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 January 1, 2004 KX1 00.2 & KX200.4 T ech- nical Manual.
Features KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 Page 2 R adically Adv anced Chassis with removable shroud and impr oved heatsink technology . The heatsinks provide the amplifier with longer runtime, improved r eliability and performance.
Custom tooled gold plated connectors Assure maximum power transfer and damping. SAMS ( S ter eo A nd M ono S imultaneously) Amplifier will operate into a bridged mono load and a stereo load at the same time. This type of system is great if the consumer is just starting out, or on a tight budget.
When selecting a location to mount your Kicker amplifier be sure it is structurally sound and that there are no items behind the ar ea that could be damaged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc. All amplifiers generate heat under normal opera- tion.
SOURCE UNIT WA R NING-Use Only One... Never Both At The Same T ime!!! Speaker Outputs RCA Outputs LEFT + LEFT - RIGHT - RIGHT + High-Level Inputs KX1 00.
SOURCE UNIT WA R NING-Use Only One... Never Both At The Same T ime!!! Speaker Outputs RCA Outputs LEFT + LEFT - RIGHT - RIGHT + AMP 1 AMP 2 High-Level Inputs LEFT + LEFT - RIGHT - RIGHT + KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 Page 6 KX200 .
Wiring Instructions SOURCE UNIT Speaker Outputs RCA Dummy Plugs LEFT + LEFT + LEFT - RIGHT - RIGHT + AMP 1 AMP 2 High-Level Inputs LEFT - RIGHT - RIGHT + When using both sets of High L ev el inputs , the supplied RCA dumm y plugs must b e inserted into the AMP 2 inputs in order for the fa der to work properly .
Wiring cont. The use of twisted pair interconnects is recommended for all installations to minimize noise. When r outing these cables through the automobile, try to keep them away from factory wiring har nesses and other power wiring. If you need to cross any of this wiring do so at a 90 degree angle to r educe the possibility for noise problems.
A djusting Amplifier Controls On your Kicker amplifier there are r otary controls and switches on the end panel. These controls ensure the relia- bility and performance of the amplifier , so they need to be set correctly . If you are using a KX150.4 you will have two sets of rotary controls and switches.
Crosso v er Control Where you set the crossover is very subjective and can be fine tuned to match your listening pr eference or speaker requirement. If the amplifier is driving small speakers (cr ossover set to HI P ASS) this will eliminate the low frequencies from damaging the high fr equency speaker .
GROUND REMOTE TURN-ON BA T TER Y +12V FUSE RIGHT SPEAKER(S) LEFT SPEAKER(S) + _ + _ 18" or less 2 Ω Min. 2 Ω Min. SIGNAL IN When the amplifier is driving speaker s that do not require a crosso ve r , the crosso ver switch may b e set to the OFF position.
GROUND REMOTE TURN-ON BA T TER Y +12V FUSE 18" or less + _ MONO SPEAKER 4 Ω Min. SIGNAL IN If the amplifier is used to drive sub woofers , set the switch to LO P ASS. This will allow only low fr equencies to pass through the amplifier to the woofer s.
GROUND REMOTE TURN-ON BA T TER Y +12V FUSE RIGHT SPEAKER(S) LEFT SPEAKER(S) + _ + _ 18" or less + _ MONO SPEAKER HIGH PASS CROSSOVER LOW PAS S CROSS- OVE R HIGH P ASS CROSSOVER 4 Ω Min. 2 Ω Min. 2 Ω Min. SIGNAL IN When the amplifier is driving speakers in the configur ation abo ve, the crosso ver switch should be set to the OFF position.
When AMP 1 or AMP 2 are driving speak ers that do not require a crosso ve r , the crosso ver switch may b e set to the OFF position. This will allow the speaker s to play full range . OR... If AMP 1 or AMP 2 are driving speak ers that do require a crosso ve r set the switch to HI P ASS.
+ - GROUND REMOTE TURN-ON BA T TER Y +12V FUSE 18" or less + - + - SIGNAL IN AMP 1 SIGNAL IN AMP 2 When AMP 1 is driving speaker s that do not require a crosso ver , the crosso ver switch may b e set to the OFF position. This will allow the speaker s to play full range .
+ - + - GROUND REMOTE TURN-ON BA T TERY +12V FUSE 18" or less If AMP 1 or AMP 2 are used to drive sub woof er s, set the switch to L O PASS. This will allow only low fr equencies to pass through the amplifier to the woofer s. MAKE SURE: * The LEFT input must be split up an d fed to the L & R Amp 1 inputs with a Y-A dapter .
Formulas KX1 00.2 & KX200.4 T echnical Manual V ersion 2.0 Page 17 Ohm’s La w E = I X R Wher e: E = V oltage (V olts) I = Curr ent (Amps or Amper es) R = R esistance (Ohms or W W ) F ormula V ar.
(T otal RMS power output into 4 W W ) x 2 = (T otal input wattage [W atts]) (T otal input wattage) = (Maximum input current [Amps]) (Supply V oltage) Example: Amplifier with a r ating of 1 00 watts per channel into 4 W W 200 x 2 = 400 W atts (T otal input po wer) 400 W atts / 12.
• Damage due to improper installation. • Subsequent damage to other components. • Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation. • Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be consider ed abuse.
P .O . Box 459 – Stillw ater , Oklahoma 74076 – U.S.A. – 405 624-85 1 0 or www .Kick er .com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Kicker KX200.4 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Kicker KX200.4 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Kicker KX200.4, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Kicker KX200.4 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Kicker KX200.4, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Kicker KX200.4.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Kicker KX200.4. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Kicker KX200.4 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
