Manuel d'utilisation / d'entretien du produit SSM2166 du fabricant Analog Devices
Aller à la page of 15
a SSM2166* Microphone Preamplifier with Variable Compression and Noise Gating Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use.
Parameter Symbol Conditions Min Typ Max Units AUDIO SIGNAL PATH Voltage Noise Density e n 15:1 Compression 17 nV/ √ Hz Noise 20 kHz Bandwidth, V IN = GND –109 dBu 1 Total Harmonic Distortion THD+N 2nd and 3rd Harmonics, V IN = –20 dBu 0.
SSM2166 REV. A –3– PIN DESCRIPTION Pin # Mnemonic Function 1 GND Ground 2 GAIN ADJUST VCA Gain Adjust Pin. A resistor from this pin to ground sets the fixed gain of the VCA. To check the setting of this pin the compression pin (Pin 10) should be grounded for no com- pression.
SSM2166 REV. A –4– 0 –80 –80 0 –70 –60 –50 –40 –30 –20 –10 –10 –40 –50 –60 –70 –20 –30 T A = +25 ° C V+ = 5V V IN = 300mV rms @ 1kHz R L = 100k V NOISE GATE SETTING 550µV rms ROTATION POINT 300mV rms GAIN ADJUST (PIN 2) = 1.
SSM2166 REV. A –5– ROTATION POINT – V rms R ROT PT RESISTOR – k V 1.0 0.1 0.01 04 5 51 0 3 5 4 0 15 20 25 30 50 55 T A = +25°C V+ = 5V R L = 100k V COMPRESSION RATIO = 1:1 NOISE GATE SETTING 550 m V rms GAIN ADJUST (PIN 2) = 1.25k V 60 65 70 75 80 85 90 Figure 9.
SSM2166 REV. A –6– APPLICATIONS INFORMATION The SSM2166 is a complete microphone signal conditioning system on a single integrated circuit. Designed primarily for voiceband applications, this integrated circuit provides amplifi- cation, rms detection, limiting, variable compression, and down- ward expansion.
SSM2166 REV. A –7– AUDIO +IN BUF OUT 53 2 V OUT 9 NOISE GATE 11 ROTATION POINT ADJUST 10 1 GND 13 VCA R 7 RMS LEVEL DETECTOR INPUT BUFFER VCA VCA IN SSM2166 R2 = 10k V 1 m F CONTROL CIRCUITRY 12 POWER DOWN POWER DOWN R GAIN COMPRESSION RATIO SET R COMP 8 C AVG 2.
SSM2166 REV. A –8– 10 0% 100 90 100mV 1S 6dBV 66dBV 85dBV Figure 15b. RMS Level Detector Performance with C AVG = 22 µ F Control Circuitry The output of the rms level detector is a signal proportional to the log of the true rms value of the buffer output with an added dc offset.
SSM2166 REV. A –9– The gain of the VCA can be reduced below 0 dB by making R GAIN smaller than 1 k Ω . Switching Pin 2 through 330 Ω or less to ground will mute the output. Either a switch connected to ground or a transistor may be used, as shown in Figure 19.
SSM2166 REV. A –10– C X 1000pF C1 0.1 m F AUDIO IN (R S > 5k V ) 7 +IN SSM2166 NOTE: ADDITIONAL CIRCUIT DETAILS OMITTED FOR CLARITY. Figure 21. Circuit Configuration for Use with High Impedance Signal Sources The value of the C7 should be the same as C6, the capacitor value used between BUF OUT and VCA IN .
SSM2166 REV. A –11– Figure 23c. Evaluation Board Backside Metallization (Not to Scale) Signal sources are connected to the SSM2166 through a 1/8" phone jack where a 0.1 µ F capacitor couples the input signal to the SSM2166’s +IN pin (Pin 7).
SSM2166 REV. A –12– or an audio cable, then the onboard OP113 can be used. To use the OP113 buffer, insert Jumper J4 into board socket pins labeled “4” and “5” and insert Jumper J5 into board socket pins labeled “6” and “7.
SSM2166 REV. A –13– STEP 5. Adjusting the Rotation Point Set the input level to 15 mV, and observe the output on the os- cilloscope. Adjust R3—ROTATION PT ADJ CW until the output level just begins to drop, then reverse so that the output is 500 mV.
SSM2166 REV. A –14– SSM2166 Demo Board Parts List R1 10k* Feedback R2 10k Input R3 50k Pot Rotation Point, Adj. R4 1k Rotation Point, Fixed R5 0 Comp Ratio, Fixed R6 100k Pot Comp Ratio, Adj. R7 1M Pot Noise Gate, Adj. R8 1k Noise Gate, Fixed R9 1k Gain Adj.
SSM2166 REV. A –15– OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 14-Lead Plastic DIP (N-14) 14 17 8 0.795 (20.19) 0.725 (18.42) 0.280 (7.11) 0.240 (6.10) PIN 1 0.325 (8.25) 0.300 (7.62) 0.015 (0.381) 0.008 (0.204) 0.195 (4.95) 0.115 (2.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Analog Devices SSM2166 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Analog Devices SSM2166 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Analog Devices SSM2166, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Analog Devices SSM2166 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Analog Devices SSM2166, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Analog Devices SSM2166.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Analog Devices SSM2166. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Analog Devices SSM2166 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.