Manuel d'utilisation / d'entretien du produit MVP-5200i-GB du fabricant AMX
Aller à la page of 196
Operation/Reference Guide Touch Panels MVP-5200i Modero ® ViewPoint ® Touch Panel with Intercom, 5.2" and 5” Last Revised:8/17/2012.
AMX Limited Warranty and Disclaimer This Limited W arranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partn er which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity .
AMX Software License and Warranty Agreement • LICENSE GRANT . AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, no t sold. This license does not grant Licensee the right to create derivative wor ks of t he AMX Software.
FCC Information This device complies with Part 15 of the FCC Rules. Operati on is subject to the fol lowing two condition s: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived; in cluding in terference that may cause undesi red operation.
Table of Contents 1 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” Table of Contents Introduction .................. ...................................................................... ................ 1 Overview ..........
2 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” Table of Contents DHCP .. ............. ................ ............. ............. ................ ............. ............. ................ ........ .. 21 Configuring Wireless Network Access .
Table of Contents 3 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” EAP Security & Server Certific ates - Overview ...................... .................... ............. 65 EAP-LEAP ............ ............. ...........
4 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” Table of Contents @DPG ..... .............. ............ ............ ............ .............. ............ ............ ............... ............ ... ........ ... 100 @PDR .
Table of Contents 5 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” ^BRD ...... ............... ............ ............ ........... ............ ............... ............ ............ ........... ..... .......... .. 118 ^BSF .
6 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” Table of Contents ?BOP ............... ........... ............ ............ ............... ........... ............ ............ ............... ........ ............ 131 ?BRD .
Table of Contents 7 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” ^RAF, ^RMF - Embedded Codes ............... ................ ............. ................ ................. ... 145 ^RMF ...... ............ ............ ...
8 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” Table of Contents ^PHN-PRIVACY .. ........... ............... ............ ............ .............. ............ ............ ............... .......... . ... 151 ?PHN-PRIVACY .
Table of Contents 9 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” MIC...... ................ ............. ............. ............. ................ ............. ............. ............. ........ .. 170 WEP ...........
10 MVP-5200i Modero® ViewPoint® Touch Panel with Interc om, 5.2 and 5” Table of Contents.
Introduction 1 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Introduction Overview The MVP-5200i is a wireless-only ergonomic de vice capabl e of V oIP intercom telephone communications, quick wakeup and conn ection time, extended battery life for lo nger operation between char ges and includes a 5.
Introduction 2 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” The MVP-5200i comes with an inte grat ed rear "kickstand", allowing it to be u sed and displayed aw ay from a Charging Station if necessary (FIG. 2). It also comes with a p re-installed 802.
Introduction 3 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” MVP-5200i Specifications (Cont.) Power Modes: • ON: All necessary modules are power ed up and device remains o nline with the NetLinx Master . • SLEEP: Only the backlight will be turned off af ter the user selectable time of inactivity has elapsed.
Introduction 4 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” MVP-5200i Specifications (Cont.) Exter nal Components Connector: 5-pin Mini-USB connector used fo r audio output to USB headphones, programming, firmware updates, and touch panel file transfer between the PC and the target panel.
Introduction 5 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Memory The MVP-5200i comes with 128MB of Mobile DDRAM memory and 256 MB N AND Flash memory .
Introduction 6 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Navigation Wheel The MVP-5200i de vice uses a unique button wheel for all commands not directly in vo lv ing the touchscreen. This wheel, known as a na vigation whee l, is located in the upper right corner of the de vice (FIG.
Introduction 7 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Navigation Wheel Behav ior in Each Power Mode The beha vior of the na vigation whee l LED is dependent upon its s.
Introduction 8 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Turning on the MVP-5200i The MVP-5200i uses one of tw o methods to turn it on. These use either the navigation wheel or the touchscreen. T o learn which method works for your panel: 1.
Accessories 9 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Accessories Table Charging Station The MVP-5200i comes with the MV P-TCS-52 T able Charging Station ( FG5966-1X ) (FIG. 5), which acts both as a charging station a nd a direct po wer connection.
Accessories 10 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Connections and Wiring The PS3.0 is used to supply po wer to the MVP-5200i by routing incoming po wer through the .
Accessories 11 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Wall Charging Station The optional MVP-WCS-52 W all Charging Station ( FG5966-1X ) of fers the same rech arging a.
Accessories 12 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” The MVP-5200i touch panel remains locked in the MV P-WCS-52 until unlock ed by the user .
Accessories 13 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Recharging T o recharge the MVP-5200i: 1. Slide the de vice into the W all Chargi ng Station cradle bottom-f irst and make sure the de vice is fully seated in the Charging Station.
Accessories 14 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 2. Select the knockout to be remov ed from the top of th e box. The box has two knockouts, at the top left and the top right. 3. Run the po wer cable through the knockout into the box .
Accessories 15 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 6. Prepare the captiv e wires for the 2-pin 3.55 mm mi ni-captiv e wire connector used for the MVP-WCS- 52’ s power supply: Strip 0.25 inch (6.35 mm) of wire insulation off all wires.
Accessories 16 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 11 . After fully seating the screws, wipe down the area around the scre w holes with the alcohol prep pad from the Installation Kit. T ake a rubber foot and remove it s adhesi ve backing.
Accessories 17 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Installing th e Optional Metal Rou gh-In Box The optional metal rough-in box (FG037-11) is 10 inches (25.40cm) wide at its widest dimension (wider than the bezel of the W all Charging Station), and is only intended for pre c onstruction installations (FIG.
Accessories 18 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Other MVP-WCS-52 i nstallations The W all-Mounted Charging Station is designed to be inst alled in v arious different locations, such as into the face of a wooden podium or the top of a table.
Configuring Communication 19 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Configuring Communication Overview All control for a MVP-5200i touch pa nel is established through a NetL inx Master . Comm unication between the MVP and the Master con sists of us ing either W i reless Ethernet (DHCP , Static IP) or USB.
Configuring Communication 20 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” IR Communication In certain situations, the MVP-5200i may be used as an infrared remo te device for other AMX contro llers. The de vice can transmit IR over 20 feet (6.
Configuring Communication 21 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” For more information on the Setup and Pr otected Setup pages, refer to the Setup P ages section on page 41 and the Pr otected Setup P ages section on page 53.
Configuring Communication 22 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Configuring Wireless Network Access The first step in connecting the MVP- 5 200i to a wireless network is to configure the wire less communication parameters within the device’ s W ireless Se ttings page.
Configuring Communication 23 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Wireless Communicatio n Using a Static IP Address 1. From the Pr otected Setup page, press the W ireless Settings b utton to open the W ir eless Settings page.
Configuring Communication 24 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” T o acce ss the Site Survey T ool: 1. From the Pr otected Setup page, press the W ireless Settings b utton to open the W ir eless Settings page. 2. Press the Site Survey button.
Configuring Communication 25 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Step 2: Configure the Card’s Wireless Security Settings The second step in setting up the wire less card is to conf igure the W ireless Settings page.
Configuring Communication 26 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Manually entering the SSID information into the a ppropriate fields by follo wing steps 7 through 9. 3. From within the W ire less Settings page, click the Simple bu tton.
Configuring Communication 27 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Automatically Setting SSID In the Pr otected Setup page: 1. Select Wireless Settings . 2. Press the Site Survey bu tton at the bottom of the page to open the W ir e less Site Survey page (FIG.
Configuring Communication 28 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” (SSID) f ield on the touch panel’ s Network Name SSID field and on the AP’ s Basic W ireless Configur ation page. 5. T oggle the Encryption b utton (FIG.
Configuring Communication 29 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Ethernet Over USB The MVP-5200i de vice is the first G4 de vice to suppor t an "Ethernet over USB" dri ver for panel do wnloads and firmw are updates.
Configuring Communication 30 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Click on Browse Select the folder that cont ains the 'linux.inf' file 7. Click on Next . 8. The W indows XP machine no w searches for the suitable driv er (FIG.
Configuring Communication 31 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” When an IP address is as signed to th e usb0 i nterface on the de vice, W indows XP will mak e an attempt to assign an IP address to the corres ponding inter face on the W indows side.
Configuring Communication 32 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 5. In the ne w window: Select Use the following IP Addr ess . Under IP addr ess , provide an IP address (ensure that it is in the same subnet as the IP address given to the usb0 interface on the MVP-5200i).
Configuring Communication 33 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 6. Click the Edit Settings button to open the V irtual NetLinx Master Settings dialog (FIG. 34). 7. Enter the System numbe r; th e default is 1 . 8. Click OK on all open dialogs to sav e your settings.
Configuring Communication 34 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 10. Press the Reboot b utton to reboot the devi ce and conf irm changes.
Configuring Communication 35 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 6. Click the Edit Settings b utton in the Communications Settings dialog to open the V irtual NetLinx Master Settings dialog (FIG.
Configuring Communication 36 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 18. Press the Back button to return to the Pr otected Setup page, and Exit to return to the Setup page. 19. The USB connection will be signif ied by the W iF i/W ir ed/USB icon changing in to a US B icon (FIG.
Configuring Communication 37 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 5. Press the Enable/Enabled b utton until it toggles to Enabled and turns light blue. 6. The Network Interface Select field is read-only and displays th e method of communication to the web .
Configuring Communication 38 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Using the NetLinx Master To Control the G4 Panel Refer to the particular NetLinx Master’ s instruction manual for de tailed informat i on on how to do wnload the latest firmw are from www .
Configuring Communication 39 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 6. Click Ye s from the Security Alert popup windo w to agree to the installation of the G4 W ebControl application on your computer .
Configuring Communication 40 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 10. Click OK to send the password to the panel and be gin the session. A confir mation message appea rs stating "Please wait, Initial scr een loading .
Setup Pages 41 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Setup Pages Overview The MVP-5200i features on-board Setu p pages. Use the options in the Setup pages to access panel information and make v a rious conf iguration changes.
Setup Pages 42 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Navigation Buttons The following Na vigation buttons (FIG. 47) appe ar on the left side of the Setup page: Setup Page (Cont.
Setup Pages 43 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Protected Setup Pages Information on the Pr otected Setup pages is av ailable on page 53.
Setup Pages 44 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Project Information Page (Cont.) Sales Order: Displays the sales order information. Purchase Order: Displays the purchase order information. AMX IR Port s: Displays the AMX IR channel ports used by the IR Emitter on the panel.
Setup Pages 45 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Panel Information Page The Panel Information page p rovides de tailed panel information (FIG. 49). Features on this page include: FIG . 49 Panel Infor mation pag e Panel Information Page Back: Saves all changes and returns to the previous page.
Setup Pages 46 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Panel Information Page (Cont.) Shut down S tring: Displays the shutdown string used during a panel’s Shutdown mode. File System: Displays the amount of Compact Fl ash memory available on the panel.
Setup Pages 47 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Time & Date Settings Page The options on the T ime & Date Settings page (FIG. 50) allo ws setting and adjusting of time and date information on the NetLinx Master .
Setup Pages 48 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Audio Settings Page The Audio Settings page allo ws adjustment of volume le vels and panel sounds settings (FIG. 51). Features on these pages include: FIG . 51 Audio Settings pages Audio Settings Page Back: Saves all changes and returns to the previous page.
Setup Pages 49 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” WAV files - Supported Sampl e Rates The follo wing sample rates for W A V fi les ar e supported by MVP-5200i panels: Audio Settings Page (Cont.
Setup Pages 50 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Power Management Page The options on the P ower Management page allo w setting of power warni ng preferences and battery status information, and adjustment of the display times for battery warnings (FIG.
Setup Pages 51 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Power Management Pag e (Cont.) Shut down: This value deter mines the number of hours or minutes that need to pass before the panel automatically shuts down. Once shut down, the device will have to be restarted.
Setup Pages 52 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5”.
Protected Setup Pages 53 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Protected Setup Pages The Pr otected Setup page (FIG. 53) provides se cu red access to adv anced panel configuration options, including communication and se curity settings.
Protected Setup Pages 54 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” T o reboot the panel: 1. Access the Pr otected Setup page. 2. Press the Reboot button. 3. W ait until the panel completes its reboot. 4. Log back into the Pr otected Setup page, if necessary .
Protected Setup Pages 55 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” 2. Press the Shutdown button. 3. Disconnect any po wer source plugs or USB connections, if necessary . Security Settings The Security b utton on the Pr otected Setup page has three settings: Standar d , Secure , and DoD .
Protected Setup Pages 56 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” For more information on conf iguring AMX devices for a secure en vironment, pl ease refer to the guide Security Pr ofiles: Conf iguring AMX De vices F or Installation Into a Secur e En vironment , a vail able at www .
Protected Setup Pages 57 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Protected Setup Navigation Buttons The Protected Setup Navigati on Buttons (FIG. 56) appear on the left edge of the Protec ted Setup page. System Settings Page The System Settings page (FIG.
Protected Setup Pages 58 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Refer to the Ethernet Over US B section on page 29 for more deta iled information on using the System Settings page.
Protected Setup Pages 59 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Wireless Settings Page Use the options on the W ireless Settings page (FIG. 58) to configure comm unication set tings for the wireless CF card (802.11b/g), and read the device number assigne d to the panel.
Protected Setup Pages 60 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Some encryption and security featur es may or may not be supp orted: Refer to the Configuring W ireless Network Access section on page 22 for more information on conf iguring the panel for wireless netw ork access using the v a rious security options.
Protected Setup Pages 61 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Security Modes The W ireless Settings page has tw o buttons: Simple and Enterprise . Pressing the Simple button opens the W ir eless Securi ty: Simple Mode popup windo w (FIG.
Protected Setup Pages 62 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Open In the W ireless Sec urity: Simple Mode popup windo w (FIG. 59), press the Security T ype field to select Open . Open security does not utilize any encryption methodology , but requires an SSID (alp ha-numeric) entry .
Protected Setup Pages 63 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Refer to the Configuring W ir ele ss Network Access section on page 22 and the Using the Site Survey T ool section on page 23 for further deta ils on these security options.
Protected Setup Pages 64 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” WPA-PSK Settings In the W ireless Sec urity: Simple Mode popup windo w (FIG. 59), press the Security T ype field to select WP A- PSK . WP A-PSK security is desi gned for en vironments where using WP A or WP A2 is desirable, but an 802.
Protected Setup Pages 65 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” EAP Security & Server Certificates - Overview The follo wing EAP types all support a server certif .
Protected Setup Pages 66 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” EAP-LEAP In the W ireless Security: Enterprise Mode popup windo w (FIG.
Protected Setup Pages 67 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” FIG . 62 EAP-LEAP sample Cisco System Security pag e.
Protected Setup Pages 68 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” EAP-FAST In the W ireless Security: Enterprise Mode popup windo w (FIG.
Protected Setup Pages 69 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Refer to the EAP Authent ication section on page 184 and the Using the Site Survey T ool section on page 23 for further details on thes e security options.
Protected Setup Pages 70 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Refer to the EAP Auth entication section on page 184 and the Using the Site Survey T ool section on page 23 for further details on these security op tions.
Protected Setup Pages 71 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” EAP-TTLS In the W ireless Security: Enterprise Mode popup windo w (FIG.
Protected Setup Pages 72 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Refer to the EAP Auth entication section on page 184 and the Using the Site Survey T ool section on page 23 for further details on these security op tions.
Protected Setup Pages 73 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Refer to the EAP A uthentication section on page 184 for further deta ils on these security options. Refer to the Using the Site Surve y T ool section on page 23 for more information on using this feature.
Protected Setup Pages 74 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Certif icate f iles frequen tly use 5 f ile extensions.
Protected Setup Pages 75 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Calibrate Page The Calibrate page (FIG. 63) allo ws you to calibrate the touch panel for accura te bu tton selection. 1. Press and hold the center button on the navi gation wheel for 6 seconds to access the Calibrate page (see FIG.
Protected Setup Pages 76 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” G4 Web Control Settings Page An on-board VNC (V irtual Network Computing) serv er al lo ws the panel to connect to any remote PC running a VNC client. Once connected, the clie nt can vie w and control the panel re motely .
Protected Setup Pages 77 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” G4 Web Control Page ( Cont.) G4 Web C ontrol T imeout: Sets the length of time (in minutes) that the panel can remain idle, detecting no cursor movements, before the G4 Web Control session is terminated.
Protected Setup Pages 78 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Other Settings Press the Other Settings button to display the three settings options for Cache , Passwords , and SIP . Press one of the options within thre e seconds, or the th ree options buttons will slide back behind the Other Settings button.
Protected Setup Pages 79 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Password Settings Pag e The options on the P asswor d Settings page (FIG. 66 ) allow assignment of passwords req uired for users to access the Pr otected Setup page, and to release the de vice from a MVP-WCS-52 Char ging Station.
Protected Setup Pages 80 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” T o change a previously established passw ord: 1. In the P assword Settings page, press the b utton in the In P anel P asswor d Change section for the particular password to be changed.
Protected Setup Pages 81 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” SIP Settings Page The options on the SIP Settings page (F IG.
Protected Setup Pages 82 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” STUN Address: This option enables you to enter the IP address or DNS name of t he Simple T raversal of UDP through NA T s (STUN) server . This field is optional.
Protected Setup Pages 83 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Tools Press and hold the T ools button to access the MVP-5200i’ s Pan el L ogs , Panel Statistic s , and Connection Utility buttons. Each of these b uttons opens a separate page, covere d in detail belo w .
Protected Setup Pages 84 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Panel Statisti cs Page The P anel Statistics page (FIG. 69) displays acti vity between the de vice and the network in p roportions of ICSP messages, blink me ssages, and Ethernet versus wireless use.
Protected Setup Pages 85 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Connection U tility Page The Connection Utility page (FIG. 70) displays the current wi red and wireless conne ction information, including the latest link quality and signal strengt h information.
Protected Setup Pages 86 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5”.
Upgrading Firmware 87 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Upgrading Firmware Overview For the purpose of panel do wnloads, the MVP-5200i’ s do wnload procedure is not compatible with other AMX panel devices. This is due to the unique config urati on of the device.
Upgrading Firmware 88 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 2. Click the Communications Settings... b utton to open the Communications Settings dialog box (FIG. 72). 3. Click on the NetLinx Master radio b utton from the Platform Selection section.
Upgrading Firmware 89 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 7. In the A vailable Connections section, click on the IP address for the touch panel to select it. 8. In the V irtual NetLinx Master Settin gs dialog box, click OK to close the box.
Upgrading Firmware 90 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 5. If the panel f irmware v ersion is not the latest a v ailable; locate the latest firmw are f ile from the www .amx.com > T ech Center > Firmwar e Files > Moder o Pane ls section of the website.
Upgrading Firmware 91 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 8. Select the appropriate Kit f ile from within the Bro wse for Folder window (FIG.
Upgrading Firmware 92 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” A Special Note for Network Interface Connections Due to any USB connection to your PC being made th rough a Network Interf ace Connection (NIC), W indows will automatically make an y new NI C connectio n the Primary connection.
Upgrading Firmware 93 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 3. From the Advanced menu, se lect Advanced Settings... to open the Advanced Settings windo w (FIG. 78). 4. Under the Adapters And Bindings tab, the user needs to mak e sure th e Local Area Connection is not at the top of the Connections list.
Upgrading Firmware 94 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 6. When fin ished, click OK to close the Advanced Settings window and sa ve all changes.
Programming 95 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Programming Overview Y ou can program the MVP-5200i, using the commands in this section, to perform a wide variety of operations using Send_Commands and v ariable text commands.
Programming 96 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Animated Transitions Animated transitions are used to add motion and ef fects to the transition from one page to another on a panel.
Programming 97 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Since the transitions require Open GL hardware acce leration, the y are not seen by the user on a VNC connection.
Programming 98 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Touch Gesture Recognition Gesturing refers to the act of moving a f i nger or styl us across the overlay and ha ving the panel recognize and process this motion as a gesture.
Programming 99 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Gesture VNC/Mouse Support Gestures are recognized wh ether or not the user is us ing a f inger or stylus on the panel's screen o verlay , a mouse on a VNC connection, or a mouse connected to the local USB port on the panel.
Programming 100 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Page Commands These Page Commands are used in NetLinx Pr ogramming Language and are case insensitive. Page Commands @APG Add a specific popup page to a specified popup group.
Programming 101 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Page Commands (Cont.) @PHP Set the hide effect position. Only 1 coordinate is ever needed for an effe ct; however , the command will specify both. This command sets the location at which the effect will end at.
Programming 102 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Page Commands (Cont. ) @PPG T oggle a specific popup page on either a specified page or the current page. If the page name is empty , the current page is used (see example 2).
Programming 103 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Page Commands (Cont.) @PPT Set a specific popup page to timeout within a specified time.
Programming 104 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Page Commands (Cont. ) PPOF Deactivate a specific popup page on either a specified page or the current page. If the page name is empty , the cu rr ent page is used (see example 2).
Programming 105 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Programming Numbers The following information provides the progra mming numbers for colors, fonts, and borders. Colors can be used to set the colors on buttons, slider s, and pages.
Programming 106 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” RGB Values for all 88 Basic Colors (Cont.) Index No . Name Red Green Blue 46 Dark Aqua 0 64 127 47 V er y Dark Aq.
Programming 107 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Font Styles And ID Numbers Font styles can be used to program the text fonts on b uttons, sliders, and pages. The following chart shows the default font type and th eir respecti ve ID numbers generated by TPDesign4.
Programming 108 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” TPD4 Border Styles by Name (Cont.) No. Border styles No. Border styles 13 Circle 65 39 D iamond 45 14 Circle 75 4.
Programming 109 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands These Button Commands are used in Ne tLinx Studio and are case insensitive. All commands that begin with " ^ " hav e the capability of assigning a v a riable text address range and button state range.
Programming 110 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^BA T Append non-unicode text. Syntax: "'^BAT-<vt addr range>,<button states range>,<new text>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 111 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^BCF Set the fill color to the specified color .
Programming 112 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^BFB Set the feedback type of the button. ONL Y works on General-type buttons. Syntax: "'^BFB-<vt addr range>,<feedback type>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 113 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^BMC Button copy command. Copy attributes of the source button to all the destination buttons. Note that the source is a single button state.
Programming 114 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^BMF Set any/all button parameters by sending embedded codes and data.
Programming 115 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^BMF (Cont.) ’%GI<bargraph invert>’ = Set the bargraph invert/noninvert or joystick co ordinate (0,1,2,3). ^GIV section on page 122 more information.
Programming 116 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^BMI Set the button mask image. Mask image is used to crop a borderless button to a non-squar e shape. This is typically used with a bitmap.
Programming 117 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^BNC Clear current Ta k e N o t e annotations. Syntax: "'^BNC-<vt addr range>,<command value>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 118 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^BOR Set a border to a specific border style associated with a border value for those buttons with a defined address range. Refer to the Border Styles and Programming Numbers table on page 107 for more information.
Programming 119 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^BSF Set the focus to the text area. Note : Select one button at a time (single vari able text address). Do not assign a variable text address range to set focus to multiple buttons.
Programming 120 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^BVN Set the computer control remote host for the specified address.
Programming 121 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^DPF Delete page flips from button if it already exists. Syntax: "'^DFP-<vt addr range>,<actions>,<page name>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 122 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^GDI Change the bargraph drag increment. Syntax: "'^GDI-<vt addr range>,<bargraph drag increment>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 123 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^GRU Change the bargraph ramp-up time in 1/10th of a second. Syntax: "'^GRU-<vt addr range>,<bargraph ramp up time>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 124 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^IRM Set the IR channel. Pulse the given IR channel for onTime in tenths of seconds. Delay offT ime in tenths of a second before the next IR pulse is allowed.
Programming 125 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont.) ^JST Set text alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '.
Programming 126 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” "^" Button Commands (Cont .) ^TEF Set the text effect.
Programming 127 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Miscellaneous MVP Strings The following two strin gs are sent by the MV P panel back to the communicating Master: MVP Panel Loc k Passcode C ommands These commands are used to maintain a passcode list.
Programming 128 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Text Effects Names The follo w ing is a listing of text ef fects names associated with the ^TEF command o n page 126. Button Query Commands Button Query commands reply back with a custom ev ent.
Programming 129 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” { Send_String 0,"'ButtonGet Id=',ITOA(CUSTOM.ID),' Type=' ,ITOA(CUSTOM.TYPE)" Send_String 0,"'Flag =',ITOA(CUSTOM.FLAG)" Send_String 0,"'VALUE1 =',ITOA(CUSTOM.
Programming 130 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Button Query Commands (Cont.) ?BCF Get the current fill color . Syntax: "'?BCF-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 131 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Button Query Commands (Cont.) ?BMP Get the current bitmap name. Syntax: "'?BMP-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 132 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Button Query Commands (Cont.) ?BRD Get the current border name. Syntax: "'?BRD-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 133 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Button Query Commands (Cont.) ?FON Get the current font index. Syntax: "'?FON-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 134 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Button Query Commands (Cont.) ?JSB Get the current bitmap justification. Syntax: "'?JSB-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 135 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Button Query Commands (Cont.) ?JST Get the current text justification. Syntax: "'?JST-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 136 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Button Query Commands (Cont.) ?TEF Get the current text effect name. Syntax: "'?TEF-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 137 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Panel Runtime Operations Serial Commands are used in T erm inal Emulator m ode. These comm ands are case i nsensitive. Panel Runtime Op eration Commands ABEEP Output a single beep even if beep is Off.
Programming 138 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Panel Runtime Operatio n Commands (Cont.) @AKP Pop up the keypad icon and initialize the tex t string to that specified. Keypad string is set to null on power up and is stored until power is lost.
Programming 139 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Panel Runtime Operatio n Commands (Cont.) PKEYP Present a private keypad. Pops up the keypad icon and initializes the text string to that specified. Keypad displays a '*' instead of the numbers typed.
Programming 140 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Panel Runtime Operatio n Commands (Cont.) @TKP Present a telephone keypad. Pops up the keypad icon and initializes the text string to that specified. The Prompt T ext is optional.
Programming 141 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Input Commands These Send Commands are case insensitiv e. Input Command s ^CAL Put panel in calibration mode. Syntax: "'^CAL'" Example: SEND COMMAND Panel,"'^CAL'" Puts the panel in calibration mode.
Programming 142 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Embedded codes The following is a list of G4 compatible embedded codes: Embedded Codes Decimal numbers Hexidecima.
Programming 143 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Panel Setup Commands These commands a re case insensi tiv e. Panel Setup Commands @PWD Set the page flip pas sw ord .
Programming 144 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Dynamic Image Commands The following table describe s Dynamic Image Commands. Dynamic Image Commands ^BBR Set the bitmap of a button to use a par tic u la r resource.
Programming 145 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” ^RAF, ^RMF - Embedded Codes The ^RAF and ^RMF commands add and modify any and all resource pa rameters by sendin.
Programming 146 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Escape Sequences The ^RAF and ^RMF commands support the replacement of any special escape se quences in the filen.
Programming 147 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Intercom Commands The following is a list of Intercom Commands: Intercom Co mmands ^MODEL? Sets model name. Panel model name. If the panel supports interc om hardware it will respond with its model name as shown in the response below.
Programming 148 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Intercom Co mmands (C ont.) ^ICM-T ALK ^ICM-LISTEN Intercom modify command. Intercom modify command. For backwards compatibility both versions are supported. In this release, however , th e T ALK and LISTEN sub commands are ignored.
Programming 149 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” SIP Commands The following table list s and describes SIP commands that are generated from the touch panel. SIP Commands ^PHN- AUTOANSWER Provides the state of the auto-answer feature.
Programming 150 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” The follo wing table lists an d describes SIP commands that are sent to the touch panel to manage calls. SIP Commands (Cont.) ^PHN- MSGW AIT ING Indicates the number of messages waiting in the user ’s voice mail box.
Programming 151 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” SIP Commands (Cont.) ?PHN- AUTOANSWER Queries the state of the auto- answer feature.
Programming 152 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” The follo wing table lists and describes SIP setup comma nds. Using any of these co mm ands causes the current user to go of fline. SIP Commands (Cont.) ^PHN- TRANSFER T ransfers the call to the provided number .
Programming 153 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” SIP Setup Commands (Cont.) ^PHN-SETUP- USERNAME Sets the user name for authentication with the proxy server .
Programming 154 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5”.
Battery Life and Replacem ent 155 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Battery Life and Replacement Overview The battery po wering the MVP-5200i is designed for upwards of 300 deep discharge rechar gings.
Battery Life and Replacement 156 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Power Management Since the MVP-5200i is a battery-power ed handheld dev ice, powe r management is a nece ssary concern. Under activ e use, the charge on the inte gral Lithium-Polymer ba ttery can last for as long as fi ve days.
Battery Life and Replacem ent 157 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Battery Replacement The touch panel 's battery is intend ed to last the life of the de vice, b ut in cases where the batte ry has reached it s effecti ve end of life, it may be replaced with the MVP-BP-5X Battery Pack Kit ( FG5966-27 ).
Battery Life and Replacement 158 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Remove the Old Battery Peel the hinge cov er film from the hinges on either side of the battery before removing the b attery . If the battery is attached to the interior of the de vice with adhesi ve tape, carefully pry the battery free.
Battery Life and Replacem ent 159 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” 4. Insert the fi ve scre ws and replac e the rubber feet atop th e two upper scre ws, using the replacement rubber feet and bottom label included in the Battery Pa ck Kit (FIG.
Battery Life and Replacement 160 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5”.
Appendix A: Text Formatti ng 161 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Appendix A: Text Formatting Text Formatting Codes for Bargraphs/Joysticks T ext formatting code.
Appendix A: Text Formatting 162 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Text Area Input Masking T ext Area Input Masking may be used t o limit the al lowed/correct characters that are entered into a text area.
Appendix A: Text Formatti ng 163 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Input Mask Ranges These ranges allo w a user to specify the minim um and maximum numeric v alue for a field. Only one range is allow ed per field.
Appendix A: Text Formatting 164 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” When data ov erflows from a numerical field, the ov erflo w value is added to the pre vious field on the chain if the ov erflo w character w as specif ied.
Appendix A: Text Formatti ng 165 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Other used escape seque nces include: Escape Sequences Sequence Panel Inf or mation $DV Device .
Appendix A: Text Formatting 166 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Complex Script Support In many cases, a user needs a touch pa nel user interface that utilize s a font appli cable to th e area for wh ich its use is intended, and to accomplish th is without needing to resort to images of properly formed text.
Appendix A: Text Formatti ng 167 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” For more information on TPDesign4 and its complex script support, please refer to the TPDesign4 (v3.0 or high er) Operation Reference Guide , available at www .
Appendix A: Text Formatting 168 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5”.
Appendix B: Wireless Technology 169 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” Appendix B: Wireless Technology Overview of Wireless Technology 802.11b/2.4 GHz and 802.11a/5 GHz are the tw o major WLAN sta ndards and both operate using radio frequency (RF) technology .
Appendix B: Wireless Technology 170 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Terminology 802.1x IEEE 802.1x is an IEEE standard that is built on the Internet standard EAP (Extensibl e Authentication Protocol). 802.1x is a standard for pa ssing EAP messages o ver either a wi red or wireless L AN.
Appendix B: Wireless Technology 171 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” T o resolve problems with WEP , the Wi -Fi Alliance relea sed WP A (FIG. 87), which integrated 802.1x , TKIP and MIC . W ithin the WP A specification s, the RC4 cipher engine was mai ntained from WEP .
Appendix B: Wireless Technology 172 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” EAP Authentication EAP (Extensible Authentication Protocol) is an Enterprise authe nticati on protocol that can be used in both a wired and wireless network en vironm ent.
Appendix B: Wireless Technology 173 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” EAP Communication Overview EAP Authentication goes a step beyond just encrypting data tr ansfers, but also requires that a set of credentials be va lidated before the client (panel ) is allo wed to connect to the rest of the network (FIG.
Appendix B: Wireless Technology 174 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” Configuring Modero Firmware via the USB Port The MVP-5200i needs to be configured to connect with a PC to transfer f irmware via the mini-USB port.
Appendix B: Wireless Technology 175 MVP-5200i Modero® ViewPoi nt® Touch Panel with Intercom, 5.2 and 5” AMX Certificate Upload Utility The Certificate Upload utility gi ves you the ability to comp.
Appendix B: Wireless Technology 176 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” 11 . Once the list i s complete, c lick on the File drop-do wn menu and select the Sav e option.
Appendix C: Troubleshooting 177 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Appendix C: Troubleshooting Overview This section describes the solutions to possible hardware/firmware issues that could arise during the common operation of a Modero touch panel.
Appendix C: Troubleshooting 178 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5” MVP-5200i Isn’t Appear ing In The Online Tr ee Tab 1. V erify that the System number is the same on both the NetLinx Projec t Navigator windo w and the System Settings page on the device.
Appendix C: Troubleshooting 179 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5” Panel Behaves Strangely After Down loading A Panel File Or Firmware Symptom: After downloading a panel f ile or firmware to a G4 de vice, the panel behaves strangely .
Appendix C: Troubleshooting 180 MVP-5200i Modero® ViewPoint® Touch Panel with Intercom, 5.2 and 5”.
Appendix C - Troubleshooting 181 MVP-5200i Modero® ViewPoint® Touc h Panel with Intercom, 5.2 and 5”.
8/2012 © 2012 AMX. All rights reserved. AMX a nd the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifica tions without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté AMX MVP-5200i-GB c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du AMX MVP-5200i-GB - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation AMX MVP-5200i-GB, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le AMX MVP-5200i-GB va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le AMX MVP-5200i-GB, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du AMX MVP-5200i-GB.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le AMX MVP-5200i-GB. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei AMX MVP-5200i-GB ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
